INSTALLATION
Removal / installation · Vehicles built from Nov 2005
| 1. INSTALL SKID CONTROL SENSOR |
Wipe the sealant off the skid control sensor installation surface using white gasoline.
- NOTICE:
- Keep the sensor rotor free of foreign matter.
Install the skid control sensor onto the rear axle hub in the highest possible installation position.

- HINT:
- The distance between the installation holes should be larger on the upper side than the lower side.
Using SST and a press, install a new skid control sensor into the rear axle hub until it is flush with the end.

- SST
- 09214-76011
- NOTICE:
- Do not use a hammer when installing.
- Check for any foreign matter on the sensor probe.
- Press the skid control sensor in slowly without turning it.
- Do not use a hammer when installing.
| 2. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY |
![]() ![]() |
for Rear Drum Brake:
Install the axle hub and bearing onto the axle beam with the 4 bolts.
- Torque:
- 90 N*m{ 918 kgf*cm , 67 ft.*lbf }
for Rear Disc Brake:
Install the dust cover and the axle hub and bearing onto the axle beam with the 4 bolts.
- Torque:
- 90 N*m{ 918 kgf*cm , 67 ft.*lbf }
| 3. INSPECT REAR AXLE HUB BEARING |
Remove the rear wheel.
for Rear Drum Brake:
Remove the rear brake drum (Click here).
for Rear Disc Brake:
Disconnect the parking brake cable (Click here).
Separate the rear disc brake caliper (Click here).
Remove the rear disc (Click here).
Inspect the axle hub and bearing backlash.

Using a dial indicator, check the backlash near the center of the axle hub.
- Maximum:
- 0.05 mm (0.0020 in.)
Inspect the axle hub and bearing runout.

Using a dial indicator, check the runout of the surface of the axle hub.
- Maximum:
- 0.07 mm (0.0028 in.)
for Rear Drum Brake:
Install the rear brake drum.
for Rear Disc Brake:
Install the rear disc (Click here).
Install the rear disc brake caliper (Click here).
Connect the parking brake cable (Click here).
Install the rear wheel.
- Torque:
- 103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }
| 4. CONNECT SKID CONTROL SENSOR WIRE |
![]() ![]() |
Connect the skid control sensor wire connector.
| 5. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake) |
| 6. INSTALL REAR DISC (for Rear Disc Brake) |
![]() ![]() |
Align the matchmarks of the disc and axle hub and install the disc.
- NOTICE:
- When replacing the disc, select the position that gives the minimum disc runout.
| 7. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for Rear Disc Brake) |
![]() ![]() |
Install the disc brake caliper onto the rear axle beam.
- Torque:
- 57 N*m{ 585 kgf*cm , 42 ft.*lbf }
| 8. CONNECT PARKING BRAKE CABLE ASSEMBLY (for Rear Disc Brake) |
![]() ![]() |
Install the casing cap onto the rear disc brake cylinder guide.
Connect the cable end to the rear disc brake cylinder operation lever.
| 9. INSTALL REAR WHEEL |
- Torque:
- 103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }
| 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
- Torque:
- 5.4 N*m{ 55 kgf*cm , 48 in.*lbf }
| 11. CHECK ABS SENSOR SIGNAL (w/o VSC) |
| 12. CHECK VSC SENSOR SIGNAL (w/ VSC) |





