2005-2008 Yaris · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built from Nov 2005


1. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

C130314E01
  1. for Rear Drum Brake:

    1. Install the axle hub and bearing onto the axle beam with the 4 bolts.

      Torque:
      90 N*m{ 918 kgf*cm , 67 ft.*lbf }

  1. for Rear Disc Brake:

    1. Install the dust cover and the axle hub and bearing onto the axle beam with the 4 bolts.

      Torque:
      90 N*m{ 918 kgf*cm , 67 ft.*lbf }


2. INSPECT REAR AXLE HUB BEARING
  1. Remove the rear wheel.

  1. for Rear Drum Brake:

    1. Remove the rear brake drum (Click here).

  1. for Rear Disc Brake:

    1. Disconnect the parking brake cable (Click here).

    2. Separate the rear disc brake caliper (Click here).

    3. Remove the rear disc (Click here).

  1. C130300E01
    Inspect the axle hub and bearing backlash.

    1. Using a dial indicator, check the backlash near the center of the axle hub.

      Maximum:
      0.05 mm (0.0020 in.)

      If the backlash exceeds the maximum, replace the axle hub and bearing.

  1. C130301E01
    Inspect the axle hub and bearing runout.

    1. Using a dial indicator, check the runout of the surface of the axle hub.

      Maximum:
      0.07 mm (0.0028 in.)

      If the runout exceeds the maximum, replace the axle hub and bearing.

  1. for Rear Drum Brake:

    1. Install the rear brake drum.

  1. for Rear Disc Brake:

    1. Install the rear disc (Click here).

    2. Install the rear disc brake caliper (Click here).

    3. Connect the parking brake cable (Click here).

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


3. CONNECT SKID CONTROL SENSOR WIRE

C107565
  1. Connect the skid control sensor wire connector.


4. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY (for Rear Drum Brake)

5. INSTALL REAR DISC (for Rear Disc Brake)

C108951E01
  1. Align the matchmarks of the disc and axle hub and install the disc.

    NOTICE:
    When replacing the disc, select the position that gives the minimum disc runout.


6. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY (for Rear Disc Brake)

C130313
  1. Install the disc brake caliper onto the rear axle beam.

    Torque:
    57 N*m{ 585 kgf*cm , 42 ft.*lbf }


7. CONNECT PARKING BRAKE CABLE ASSEMBLY (for Rear Disc Brake)

C129770
  1. Install the casing cap onto the rear disc brake cylinder guide.

  1. Connect the cable end to the rear disc brake cylinder operation lever.


8. INSTALL REAR WHEEL

Torque:
103 N*m{ 1,050 kgf*cm , 76 ft.*lbf }


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


10. CHECK ABS SENSOR SIGNAL (w/o VSC)
(Click here)

11. CHECK VSC SENSOR SIGNAL (w/ VSC)
(Click here)
← REMOVAL (from Nov 2005)PROBLEM SYMPTOMS TABLE (from Jan 2006) →