2005-2008 Yaris · Service Manual ENGINE

ADJUSTMENT

Removal / installation · Vehicles built from Aug 2005


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

2. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

A116530E01
  1. Remove the 4 clamps.

  1. Remove the 2 clamps and remove the air cleaner cap.


3. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

A104300
  1. Remove the air cleaner filter element from the cylinder head cover.


4. REMOVE IGNITION COIL NO. 1

A116531
  1. Disconnect the 3 connectors.

  1. Remove the 3 bolts and 3 ignition coils.


5. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A105015
  1. Disconnect the VSV connector and disengage the wire harness clamp.

  1. Disconnect vapor feed hoses No. 1 and No. 2.

  1. A107415
    Disconnect the ventilation hose.

  1. A116535
    Remove the bolt and separate the oxygen sensor wire harness.

  1. Separate the wire harness.

  1. A104153E03
    Remove the 13 bolts and 2 nuts in the order shown in the illustration and remove the cylinder head cover with the gasket.


6. SET NO. 1 CYLINDER TO TDC/COMPRESSION

A107397E01
  1. Turn the crankshaft pulley clockwise to align the timing mark on the pulley with the timing pointer of the timing chain cover.

  1. Make sure that the timing mark of the camshaft sprocket is at the top.

    HINT:
    If the matchmarks do not align, turn the crankshaft clockwise one complete revolution and then check that they align.


7. INSPECT VALVE CLEARANCE

A104123
  1. Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Valve clearance (Cold):
      Intake side:
      0.145 to 0.235 mm (0.00571 to 0.00925 in.)
      Exhaust side:
      0.275 to 0.365 mm (0.01083 to 0.01437 in.)

      HINT:
      Insert the feeler gauge from the spark plug side (center).

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.

  1. Turn the crankshaft 1 revolution (360°).

  1. A104124
    Check only the valves indicated.

    1. Using a feeler gauge, measure the clearance between the valve lifter and camshaft.

      Valve clearance (Cold):
      Intake side:
      0.145 to 0.235 mm (0.00571 to 0.00925 in.)
      Exhaust side:
      0.275 to 0.365 mm (0.01083 to 0.01437 in.)

      HINT:
      Insert the feeler gauge from the spark plug side (center).

    2. Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.


8. ADJUST VALVE CLEARANCE
  1. Remove the No. 1 and No. 2 camshafts (Click here).

  1. Remove the valve lifters (Click here).

  1. A001082
    Using a micrometer, measure the thickness of the removed valve lifters.

  1. Calculate the thickness of a new lifter so that the valve clearance comes within the specified value.

    A
    Thickness of new lifter
    B
    Thickness of used lifter
    C
    Measured valve clearance

    Valve clearance:
    Intake A = B + (C - 0.18 mm (0.0071 in.))
    Exhaust A = B + (C - 0.31 mm (0.0122 in.))

    HINT:
    1. Select a new lifter with a thickness as close to the calculated values as possible.
    2. Lifters are available in 29 sizes in increments of 0.020 mm (0.0008 in.), from 5.12 mm (0.2016 in.) to 5.68 mm (0.2236 in.).
    3. Refer to the New Lifter Thickness Table on the next 2 pages.

  1. Install the valve lifters (Click here).

  1. Install the No. 1 and No. 2 camshafts (Click here).

    A105103E01

    A105104E02

    HINT:
    New lifter thickness mm (in.) 
    Lifter No.
    Thickness
    Lifter No.
    Thickness
    Lifter No.
    Thickness
    12
    5.12 (0.2016)
    32
    5.32 (0.2094)
    52
    5.52 (0.2173)
    14
    5.14 (0.2024)
    34
    5.34 (0.2102)
    54
    5.54 (0.2181)
    16
    5.16 (0.2031)
    36
    5.36 (0.2110)
    56
    5.56 (0.2189)
    18
    5.18 (0.2039)
    38
    5.38 (0.2118)
    58
    5.58 (0.2197)
    20
    5.20 (0.2047)
    40
    5.40 (0.2126)
    60
    5.60 (0.2205)
    22
    5.22 (0.2055)
    42
    5.42 (0.2134)
    62
    5.62 (0.2213)
    24
    5.24 (0.2063)
    44
    5.44 (0.2142)
    64
    5.64 (0.2220)
    26
    5.26 (0.2071)
    46
    5.46 (0.2150)
    66
    5.66 (0.2228)
    28
    5.28 (0.2079)
    48
    5.48 (0.2157)
    68
    5.68 (0.2236)
    30
    5.30 (0.2087)
    50
    5.50 (0.2165)
    -
    -


9. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

A117009
  1. Clean the cylinder head cover, cylinder head assembly and timing chain cover assembly.

  1. Fit the cylinder head cover gasket into the gasket groove on the cover and onto the center bosses.

  1. A118680E01
    Apply a continuous bead of seal packing (diameter: 3.5 to 4.5 mm (0.14 to 0.18 in.)) to the contact surface between the cylinder head assembly and timing chain cover assembly, as shown in the illustration.

    Seal Packing:
    Part No. 08826-00080 or the equivalent

  1. A104153E04
    Install the bolts within 3 minutes of applying seal packing in the order shown in the illustration.

    Torque:
    7.7 N*m{ 79 kgf*cm , 68 in.*lbf }

  1. Tighten the bolts to the specified torque and make sure that bolts 1 and 2 are tightened to the specified torque shown in the illustration.

  1. Install the wire harness.

  1. A116535
    Install the oxygen sensor wire harness with the bolt.

    Torque:
    7.7 N*m{ 79 kgf*cm , 68 in.*lbf }

  1. A107415
    Connect the ventilation hose.

  1. A105015
    Connect vapor hoses No. 1 and No. 2.

  1. Connect the VSV connector.


10. INSTALL IGNITION COIL NO. 1

A116531
  1. Install the 3 ignition coils with the 3 bolts.

    Torque:
    9.2 N*m{ 94 kgf*cm , 81 in.*lbf }

  1. Connect the 3 connectors.


11. INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

A104320
  1. Install the air cleaner filter element as shown in the illustration.


12. INSTALL AIR CLEANER CAP SUB-ASSEMBLY

A116530E01
  1. Install the air cleaner cap with the 2 clamps.

  1. Tighten the 4 clamps.


13. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:
5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


14. CHECK FOR ENGINE OIL LEAKAGE
← INSTALLATION (from Aug 2005)COMPONENTS (from Aug 2005) →