Home › BRAKE › BRAKE CONTROL › ANTI-LOCK BRAKE SYSTEM (for Hatchback)

ANTI-LOCK BRAKE SYSTEM (for Hatchback) > Brake Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.
If any of the following is detected, the brake warning light remains on:
  1. The skid control ECU connector is disconnected from the skid control ECU.
  2. The brake fluid level is insufficient.
  3. The parking brake is applied.
  4. EBD operation is not possible.

WIRING DIAGRAM


C194020E01


INSPECTION PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication system DTCs are output (Click here).
    Result 
    Result
    Proceed to
    DTC not output
    A
    DTC output
    B



B
CHECK CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG (for 2NZ-FE)
    B
    NG (for 1NZ-FE)
    C



B
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)

C
CHECK OR REPLACE CHARGING SYSTEM OR BATTERY (Click here)
A


4.INSPECT SKID CONTROL ECU (IG1 TERMINAL)


    C168930E10
  1. Disconnect the skid control ECU connector.

  1. Inspect the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A15-34 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)
OK


5.INSPECT SKID CONTROL ECU (GND TERMINAL)


    C168930E13
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A15-1 (GND1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND CIRCUIT)
OK


6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH)
  1. Reconnect the skid control ECU connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Parking Brake SW
    Parking brake switch / ON or OFF
    ON: Parking brake applied
    OFF: Parking brake released
    -

  1. Using the intelligent tester, check the input of switch operation when the parking brake pedal is operated.

    OK:
    When the parking brake is operated, the display changes as shown above.



NG
Go to step 11
OK


7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH


    C170227E01
  1. Turn the ignition switch off.

  1. Remove the reservoir filler cap and strainer.

  1. Disconnect the brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch OFF (Float up)
    10 kΩ or higher
    1 - 2
    Switch ON (Float down)
    Below 1 Ω

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



NG
REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY (BRAKE FLUID LEVEL WARNING SWITCH) (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)


    C118702E06
  1. Disconnect the combination meter connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    LHD 
    Tester Connection
    Condition
    Specified Condition
    D87-2 - A10-1 (+)
    Always
    Below 1 Ω
    D87-2 - Body ground
    Always
    10 kΩ or higher
    A10-2 (E) - Body ground
    Always
    Below 1 Ω
    RHD 
    Tester Connection
    Condition
    Specified Condition
    D87-7 - A10-1 (+)
    Always
    Below 1 Ω
    D87-7 - Body ground
    Always
    10 kΩ or higher
    A10-2 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
  1. Connect the intelligent tester to the DLC3.

  1. Perform Active Test of the combination meter using the intelligent tester (Click here).

    OK:
    The brake warning light turns ON or OFF in accordance with the intelligent tester.

    HINT:
    Reinstall the connectors and restore the vehicle to its prior condition before checking the combination meter.



NG
Go to step 10
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

10.INSPECT COMBINATION METER ASSEMBLY
  1. Inspect the combination meter (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

11.INSPECT PARKING BRAKE SWITCH


    C163216E01
  1. Turn the ignition switch off.

  1. Disconnect the parking brake switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - Body ground
    Parking brake switch ON
    (Switch pin free)
    Below 1 Ω
    1 - Body ground
    Parking brake switch OFF
    (Switch pin pushed in)
    10 kΩ or higher



NG
REPLACE PARKING BRAKE SWITCH (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH)


    C120360E02
  1. Disconnect the main body ECU connector.

  1. Inspect both the connector case and the terminal for deformation and corrosion.

    OK:
    No deformation or corrosion.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    4C-2 (PKB) - D21-1
    Always
    Below 1 Ω
    4C-2 (PKB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)