Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speedometer Malfunction

for Preparation Click here


DESCRIPTION

w/ VSC (for Built-in Type Yaw Rate Sensor)
  1. The meter CPU receives vehicle speed signals from the brake actuator assembly via the CAN communication system (CAN V1 Bus). The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly. The brake actuator assembly supplies power to the vehicle speed sensor. The brake actuator assembly detects vehicle speed signals based on the pulses of the voltage.

    HINT:
    1. Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart .
    2. If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly stores the DTCs. Troubleshoot the Vehicle Stability Control System (Click here).

w/ VSC (for Separate Type Yaw Rate Sensor)
  1. The meter CPU receives vehicle speed signals from the brake actuator assembly via the CAN communication system (CAN V1 Bus). The speed sensor detects the wheel speed and sends the appropriate signals to the brake actuator assembly. The brake actuator assembly supplies power to the vehicle speed sensor. The brake actuator assembly detects vehicle speed signals based on the pulses of the voltage.

    HINT:
    1. Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart .
    2. If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly stores the DTCs. Troubleshoot the Vehicle Stability Control System (Click here).

w/o VSC (w/ ABS)
  1. The combination meter assembly controls the speedometer in accordance with vehicle speed signals from brake actuator assembly.

    HINT:
    1. Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart .
    2. If the vehicle speed sensor circuit has a malfunction, the brake actuator assembly stores the DTCs. Troubleshoot the Anti-lock Brake System (Click here).

w/o VSC (w/o ABS)
  1. The combination meter assembly controls the speedometer in accordance with vehicle speed signals from the speed sensor.

    HINT:
    Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart .


WIRING DIAGRAM


E143765E70


E231157E01


INSPECTION PROCEDURE

CAUTION:
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection .

HINT:
Before starting the following inspection, check tire size and tire air pressure.

1.SYSTEM CHECK
  1. Check the vehicle specifications.
    Result 
    Result
    Proceed to
    w/ VSC
    A
    w/o VSC (w/ ABS)
    B
    w/o VSC (w/o ABS)
    C



B
Go to step 6

C
Go to step 10
A


2.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output.

    1. except Separate Type Yaw Rate Sensor (Click here)
    1. for Separate Type Yaw Rate Sensor (Click here)
    Result 
    Result
    Proceed to
    CAN communication DTC is not output
    A
    CAN communication DTC is output (except Separate Type Yaw Rate Sensor)
    B
    CAN communication DTC is output (for Separate Type Yaw Rate Sensor)
    C



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


3.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    0, 40, 80, 120, 160, 200, 240 (km/h)
    Vehicle is stopped and the engine idling

    OK:
    Speedometer indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


4.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED METER)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/
    Min.: 0 (0)
    Max.: 255 (158)
    Approximately same as actual vehicle speed (When vehicle is being driven)
    Unit: km/h (mph)

    OK:
    Vehicle speed displayed on the intelligent tester is almost the same as the speedometer indication.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


5.CHECK VEHICLE STABILITY CONTROL SYSTEM
  1. Check if a vehicle stability control DTC is output.

    1. for Built-in Type Yaw Rate Sensor (Click here)
    1. for Separate Type Yaw Rate Sensor (Click here)
    Result 
    Result
    Proceed to
    Vehicle stability control DTC is not output
    A
    Vehicle stability control DTC is output (for Built-in Type Yaw Rate Sensor)
    B
    Vehicle stability control DTC is output (for Separate Type Yaw Rate Sensor)
    C



B
GO TO VEHICLE STABILITY CONTROL SYSTEM (Click here)

C
GO TO VEHICLE STABILITY CONTROL SYSTEM (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)  

6.READ VALUE USING INTELLIGENT TESTER (VEHICLE SPEED)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

  1. According to the display on the intelligent tester, read the Data List.

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Maximum wheel speed sensor reading
    Min.: 0 km/h
    Max.: 326 km/h
    Actual vehicle speed
    Speed indicated on speedometer

    OK:
    Vehicle speed displayed on the intelligent tester is approximately the same as the actual vehicle speed.



NG
GO TO ANTI-LOCK BRAKE SYSTEM (Click here)
OK


7.INSPECT COMBINATION METER ASSEMBLY (OUTPUT VOLTAGE)


    E186734E27
  1. Disconnect the A55 brake actuator assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A55-22 (SP1) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to brake actuator assembly)

  1. Reconnect the A55 brake actuator assembly connector.



NG
Go to step 9
OK


8.INSPECT COMBINATION METER ASSEMBLY (INPUT WAVEFORM)


    E219774E05
  1. Check the input waveform.

    1. Remove the combination meter assembly with the connector(s) still connected.

    2. Connect an oscilloscope to terminal F1-5 (SI) and body ground.

    3. Turn the ignition switch to ON.

    4. Turn the wheel slowly.

    5. Check the signal waveform according to the condition(s) in the table below.

      Standard:
      Item
      Condition
      Tool setting
      5 V/DIV., 20 ms./DIV.
      Condition
      Driving at approximately 20 km/h

      Text in Illustration 
      *a
      Component with harness connected
      (Combination Meter Assembly)
      *b
      Waveform

      OK:
      The waveform is displayed as shown in the illustration.

      HINT:
      As the vehicle speed increases, the cycle of the waveform narrows.

      Result 
      Result
      Proceed to
      OK
      A
      NG (for LHD)
      B
      NG (for RHD)
      C



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)

C
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)  

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION METER ASSEMBLY)
  1. Disconnect the F1 combination meter assembly connector.

  1. Disconnect the A55 brake actuator assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-5 (SI) - A55-22 (SP1)
    Always
    Below 1 Ω
    F1-5 (SI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

10.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SPEED METER OPERATION)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    0, 40, 80, 120, 160, 200, 240 (km/h)
    Vehicle is stopped and the engine idling

    OK:
    Speedometer indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


11.INSPECT SPEEDOMETER SENSOR
  1. Inspect speedometer sensor (Click here).



NG
REPLACE SPEEDOMETER SENSOR (Click here)
OK


12.CHECK HARNESS AND CONNECTOR (SPEEDOMETER SENSOR - COMBINATION METER ASSEMBLY)
  1. Disconnect the F1 combination meter assembly connector.

  1. Disconnect the B85 speedometer sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F1-5 (SI) - B85-3 (SI)
    Always
    Below 1 Ω
    B85-2 (SE) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the combination meter assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    B85-1 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

  1. Reconnect the speedometer sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)