AIR CONDITIONING SYSTEM (for Manual Air Conditioning System) > Blower Motor Circuit |

| 1.INSPECT HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY) |
Inspect the heater blower motor relay assembly (HTR relay) (Click here).
|
| ||||
| OK | |
| 2.INSPECT BLOWER MOTOR WITH FAN SUB-ASSEMBLY |
Inspect the blower motor with fan sub-assembly (Click here).
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY) - BATTERY, IG1 NO. 1 RELAY AND BODY GROUND) |
![]() |
Remove the heater blower motor relay assembly (HTR relay).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| HTR-5 - Body ground | Always | 11 to 14 V |
| HTR-1 - Body ground | Ignition switch ON | 11 to 14 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HTR-4 - Body ground | Always | Below 1 Ω |
| *1 | Heater Blower Motor Relay Assembly (HTR Relay) Holder |
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY) - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
Remove the heater blower motor relay assembly (HTR relay).
Disconnect the F41 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HTR-2 - F41-14 (HR) | Always | Below 1 Ω |
| HTR-2 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (NO. 2 HEATER CONTROL SUB-ASSEMBLY (BLOWER SWITCH) - AIR CONDITIONING AMPLIFIER ASSEMBLY) |
Disconnect the F39 No. 2 heater control sub-assembly (blower switch) connector.
Disconnect the F41 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F39-9 (LO) - F41-17 (SBLW) | Always | Below 1 Ω |
| F39-9 (LO) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - HEATER BLOWER MOTOR RELAY ASSEMBLY (HTR RELAY)) |
![]() |
w/ Fan Shroud Ventilation Duct
Disconnect the F96 blower motor with fan sub-assembly connector.
w/o Fan Shroud Ventilation Duct
Disconnect the F35 blower motor with fan sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F96-2 - Body ground | Ignition switch ON Blower switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| F35-2 - Body ground | Ignition switch ON Blower switch ON | 11 to 14 V |
| *A | w/ Fan Shroud Ventilation Duct |
| *B | w/o Fan Shroud Ventilation Duct |
| *a | Front view of wire harness connector (to Blower Motor with Fan Sub-Assembly) |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (BLOWER MOTOR WITH FAN SUB-ASSEMBLY - BLOWER RESISTOR) |
w/ Fan Shroud Ventilation Duct
Disconnect the F96 blower motor with fan sub-assembly connector.
w/o Fan Shroud Ventilation Duct
Disconnect the F35 blower motor with fan sub-assembly connector.
Disconnect the F34 blower resistor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F96-1 - F34-4 (HI) | Always | Below 1 Ω |
| F96-1 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| F35-1 - F34-4 (HI) | Always | Below 1 Ω |
| F35-1 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT BLOWER RESISTOR |
Inspect the blower resistor (Click here).
|
| ||||
| OK | |
| 9.INSPECT NO. 2 HEATER CONTROL SUB-ASSEMBLY (BLOWER SWITCH) |
Inspect the No. 2 heater control sub-assembly (blower switch) (Click here).
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (NO. 2 HEATER CONTROL SUB-ASSEMBLY (BLOWER SWITCH) - BLOWER RESISTOR AND BODY GROUND) |
Disconnect the F39 No. 2 heater control sub-assembly (blower switch) connector.
Disconnect the F34 blower resistor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F39-5 (E) - F34-1 (E) | Always | Below 1 Ω |
| F39-6 (M2) - F34-2 (M2) | Always | Below 1 Ω |
| F39-7 (M1) - F34-3 (M1) | Always | Below 1 Ω |
| F39-10 (HI) - F34-4 (HI) | Always | Below 1 Ω |
| F39-5 (E) - Body ground | Always | Below 1 Ω |
| F39-6 (M2) - Body ground | Always | 10 kΩ or higher |
| F39-7 (M1) - Body ground | Always | 10 kΩ or higher |
| F39-10 (HI) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||