Home › Audio/Visual/Telematics › Audio/Video › AUDIO AND VISUAL SYSTEM
Last Modified: 11-27-2007 1.6 C
Service Category: Audio/Visual/Telematics Section: Audio/Video
Model Year: 2008 Model: LX570 Doc ID: RM00000182J03IX
Title: AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: DESCRIPTION (2008 LX570)

DTC

01-D6

No Master

DTC

01-D7

Connection Check Error

DESCRIPTION

DTC Code

DTC Detection Condition

Trouble Area

01-D6*1

When either of the following conditions is met:

  • The component which has stored the code has (had) been disconnected when the engine switch is on (ACC) or on (IG).
  • The master device has (had) been disconnected when this code is stored.
  • Display and navigation assembly power source circuit (w/ Navigation System)
  • Multi-display power source circuit (w/o Navigation System)
  • Power source circuit of component which has stored this code
  • AVC-LAN circuit between the multi-display and the component which has stored this code
  • Component which has stored this code
  • Display and navigation module display (w/ Navigation System)
  • Multi-display assembly ( w/o Navigation System)

01-D7*2

When either of the following conditions is met:

  • The component which has stored the code has (had) been disconnected after the engine starts (started).
  • The master device has (had) been disconnected when this code is (was) stored.

HINT:

*1: Even if no fault is present, this trouble code may be stored depending on the battery condition or engine start voltage.

*2: When 210 seconds have elapsed after disconnecting the power supply connector of the master component with the engine switch on (ACC) or on (IG), this code is stored.

NOTICE:

  • Before starting troubleshooting, be sure to clear DTCs to clear codes stored due to the reasons described in the Hint above. Then, check for DTCs and troubleshoot according to the output DTCs.
  • The multi-display or display and navigation module display is the master unit.
  • Be sure to clear and recheck for DTCs after the inspection is completed to confirm that no DTCs are output.

WIRING DIAGRAM

INSPECTION PROCEDURE

NOTICE:

Be sure to read the Description before performing the following procedures.

HINT:

If the vehicle has a navigation system, "multi-display" refers to the "display and navigation module display".

PROCEDURE

1.

CHECK POWER SOURCE CIRCUIT

(a) w/ Navigation System: Refer to the Display and Navigation Assembly Power Source Circuit NAVIGATION / MULTI INFO DISPLAY: NAVIGATION SYSTEM: DESCRIPTION (2008 LX570) .

(b) w/o Navigation System: Refer to the Multi-display Power Source Circuit AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: DESCRIPTION (2008 LX570) .

NEXT

2.

IDENTIFY COMPONENT WHICH HAS STORED THIS CODE

(a) Enter the diagnostic mode.

(b) Press the "LAN Mon" switch to change to "LAN Monitor" mode.

(c) Identify the component which has stored this code.

Component Table

Display

Component

AUDIO

Radio receiver

DSP-AMP

Stereo component amplifier

CAMERA-C*1

Parking assist ECU

XM*2

Stereo component tuner

RSE*3

Television display

*1: w/ Wide View Front and Side Monitor System

*2: w/ SDARS System

*3: w/ Rear Seat Entertainment System

HINT:

"NAVI" is the component which has stored this code in the example shown in the illustration.

NEXT

3.

CHECK POWER SOURCE CIRCUIT OF COMPONENT WHICH HAS STORED THIS CODE

(a) Inspect the power source circuit of the component which has stored this code.

Component Table

Display

Proceed to

Radio receiver (AUDIO)

Radio receiver power source circuit AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: DESCRIPTION (2008 LX570)

Stereo component amplifier (DSP-AMP)

Stereo component amplifier power source circuit AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: DESCRIPTION (2008 LX570)

Parking assist ECU (CAMERA-C)*1

Parking assist ECU power source circuit PARK ASSIST / MONITORING: WIDE VIEW FRONT MONITOR SYSTEM: DESCRIPTION (2008 LX570)

Stereo component tuner (XM)*2

Satellite radio tuner power source circuit AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: DESCRIPTION (2008 LX570)

Television display (RSE)*3

Television display power source circuit AUDIO / VIDEO: REAR SEAT ENTERTAINMENT SYSTEM: DESCRIPTION (2008 LX570)

If the power source circuit is operating normally, proceed to the next step.

*1: w/ Wide View Front and Side Monitor System

*2: w/ SDARS System

*3: w/ Rear Seat Entertainment System

NEXT

4.

INSPECT RADIO RECEIVER ASSEMBLY


(a) Disconnect the F1, F23 and F24 receiver connectors.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F1-5 (ATX+) - F1-15 (ATX-)

Always

60 to 80 Ω

F23-9 (TX+) - F23-10 (TX-)

Always

60 to 80 Ω

F24-9 (TXM+) - F24-10 (TXM-)

Always

60 to 80 Ω
OK

5.

CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY - COMPONENT WHICH HAS STORED THIS CODE)

HINT:

For details of the connectors, refer to Terminals of ECU AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: TERMINALS OF ECU (2008 LX570) .

(a) Check the AVC-LAN circuit between the multi-display and the component which has stored this code.

(1) Disconnect all connectors between the multi-display and the component which has stored this code.

(2) Check for an open or short in the AVC-LAN circuit between the multi-display and the component which has stored this code.

OK:

There is no open or short circuit.

OK

6.

REPLACE COMPONENT WHICH HAS STORED THIS CODE

(a) Replace the component which has stored this code with a normal one and check if the same problem occurs again.

OK:

Same problem does not occur.

Result

Result

Proceed to

OK

A

NG (w/ Navigation System)

B

NG (w/o Navigation System)

C
A