Home › Engine / Hybrid System › 1GR-FE LUBRICATION › OIL PUMP › from 2014.08
RM1440E _51 Engine / Hybrid System _056130 1GR-FE LUBRICATION _0273918 OIL PUMP A

1GR-FE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 11301C 1.INSTALL FRONT CRANKSHAFT OIL SEAL

a.
A225390E07
1.365,1.708 0.833,1.708 0.833,1.708 1.229,2.333 true 0.521,1.635 0.833,1.833 0.313,0.198 10 true SST

Using SST and a hammer, tap in a new front crankshaft oil seal until its surface is flush with the timing chain cover sub-assembly edge.

SST
09223-22010  
09506-35010  

NOTICE:
·

Keep the lip free from foreign matter.

·

Do not tap on the front crankshaft oil seal at an angle.

·

Make sure that the front crankshaft oil seal edge does not protrude from the timing chain case.




Hide 11302 2.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the timing chain cover sub-assembly, cylinder head and cylinder block.

A225681E05
0.396,2.396 0.583,2.594 0.188,0.198 10 false *a 1.833,0.188 2.042,0.396 0.208,0.208 10 false *A 5.188,0.188 5.396,0.396 0.208,0.208 10 false *B

Text in Illustration
*A Cylinder head and cylinder block side *B Timing chain cover side
*a Clean and degrease - -

NOTICE:

Be sure to clean and degrease the contact surfaces, especially the surfaces indicated in the illustration.



b.

Apply a light coat of engine oil to a new oil pump gasket.


c.

Install the oil pump gasket.


d.
A225682E01
2.018,3.584 2.212,3.757 0.194,0.173 10 *1

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


Text in Illustration
*1 Seal Diameter
V100135

Seal Packing


e.

Apply seal packing to the timing chain cover sub-assembly in a continuous line as shown in the following illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


A221403E10
2.292,2.365 2.833,2.667 2.833,2.667 2.76,1.99 true 2.823,2.656 2.667,2.375 true 4.438,0.302 4.667,0.302 4.667,0.302 5.344,1.094 false 5.76,0.219 5.885,0.219 5.885,0.219 6.146,1.094 false 6.615,1.094 7.063,2.156 7.063,2.156 6.844,2.156 false 2.354,1.406 2.135,1.573 2.135,1.573 2.135,1.688 true 3.323,1.052 3.24,1.052 3.24,1.052 2.854,1.26 true 1.26,2.417 1.26,2.26 1.26,2.26 1.708,1.594 true 4.219,2.385 4.219,2.031 4.219,2.031 4.188,1.969 true 4.813,2.125 4.677,2.125 4.677,2.125 4.531,1.823 false 0.323,2.594 0.323,2.24 0.323,2.24 0.406,2.042 false 3.917,0.208 4.438,0.427 0.521,0.219 10 false 5.0 mm 6.667,2.052 6.854,2.271 0.188,0.219 10 false *g 5.604,0.146 5.76,0.313 0.156,0.167 10 false *f 2.771,2.677 3,2.833 0.229,0.156 10 true *a 1.938,1.708 2.417,1.906 0.479,0.198 10 true 20 mm 3.635,1.427 3.76,1.604 0.125,0.177 10 false A 3.521,2.229 3.646,2.406 0.125,0.177 10 true B 3.969,1.865 4.094,2.042 0.125,0.177 10 false A 3.219,2.094 3.313,2.25 0.094,0.156 10 true B 5.01,2.781 5.24,2.938 0.229,0.156 10 false *b 5.01,3.177 5.24,3.333 0.229,0.156 10 false *c 6.469,2.74 6.698,2.896 0.229,0.156 10 false *d 6.469,3.156 6.698,3.313 0.229,0.156 10 false *e 5.063,1.677 5.438,1.885 0.375,0.208 10 false A - A 6.229,1.677 6.604,1.885 0.375,0.208 10 false B - B 3.375,0.969 3.875,1.188 0.5,0.219 10 true 30 mm 1.042,2.417 1.667,2.594 0.625,0.177 10 false 30 mm 4.052,2.375 4.656,2.75 0.604,0.375 10 false 40 mm 4.844,2.052 5.448,2.427 0.604,0.375 10 false 155 mm 0.094,2.625 0.698,2.823 0.604,0.198 10 false 155 mm

Text in Illustration
*a Be sure to apply seal packing *b Dashed line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent)
*c Continuous line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) *d Alternate long and short dashed line area (Seal packing: Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent)
*e Diagonal line area (Seal packing: Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent) *f 3.0 to 4.0 mm (0.118 to 0.157 in.)
*g 2.0 to 3.0 mm (0.0787 to 0.118 in.) - -

NOTICE:
·

When the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.

·

Install the chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.



Application Specification:
Area Seal Packing Diameter Application Position from Inside Seal Line
Continuous Line Area 4.5 mm (0.177 in.) or more 3.0 to 4.0 mm (0.118 to 0.158 in.)
Alternate Long and Short Dashed Line Area 3.5 mm (0.138 in.) or more 2.0 to 3.0 mm (0.0787 to 0.118 in.)
Dashed Line Area 3.5 mm (0.138 in.) or more 3.0 to 4.0 mm (0.118 to 0.158 in.)
Diagonal Line Area 6.0 mm (0.236 in.) or more 5.0 mm (0.197 in.)



f.
A221405E08
1.302,1.448 1.188,1.448 1.188,1.448 0.948,1.615 true 2.938,1.417 2.76,1.417 2.76,1.417 2.479,1.573 true 0.708,0.979 0.979,1.146 0.271,0.167 10 true 15° 1.323,1.354 1.521,1.531 0.198,0.177 10 false *1 2.958,1.333 3.156,1.51 0.198,0.177 10 false *2

Align the oil pump drive rotor spline and crankshaft as shown in the illustration. Install the drive rotor and chain cover to the crankshaft.

Text in Illustration
*1 Drive Rotor Spline
*2 Crankshaft


g.

Install the timing chain cover sub-assembly with the 26 bolts, labeled A, B, C and D, and the 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Standard Bolt:
Item Length
Bolt A 25 mm (0.984 in.)
Bolt B 55 mm (2.17 in.)
Bolt C 35 mm (1.38 in.)
Bolt D 65 mm (2.56 in.)


A221406E05
6.677,1.458 6.583,1.458 6.583,1.458 6.323,1.24 true 4.344,1.521 4.438,1.521 4.438,1.521 4.542,1.354 false 5.24,1.24 5.292,1.24 5.292,1.24 5.375,1.365 true 4.969,2.167 4.594,2.167 true 6.427,2.198 6.042,2.198 false 6.958,0.885 6.885,0.885 6.885,0.885 6.771,0.958 false 4.031,0.854 4.115,0.854 4.115,0.854 4.219,0.99 false 6.052,0.219 5.948,0.219 5.948,0.219 5.802,0.448 false 2.052,0.302 2.177,0.479 0.125,0.177 10 false A 2.302,0.156 2.427,0.333 0.125,0.177 10 false A 1.802,0.313 1.927,0.49 0.125,0.177 10 false A 1.583,0.156 1.708,0.333 0.125,0.177 10 false A 1.635,1.031 1.76,1.208 0.125,0.177 10 true A 1.51,0.885 1.635,1.063 0.125,0.177 10 true A 2.354,0.865 2.479,1.042 0.125,0.177 10 true A 3.135,1.146 3.26,1.323 0.125,0.177 10 true A 0.406,0.958 0.531,1.135 0.125,0.177 10 false A 0.656,1.25 0.781,1.427 0.125,0.177 10 false A 2.281,1.281 2.406,1.458 0.125,0.177 10 true A 3.396,0.781 3.521,0.958 0.125,0.177 10 false B 2.927,1.521 3.052,1.698 0.125,0.177 10 false B 2.771,1.698 2.896,1.875 0.125,0.177 10 false B 2.083,1.896 2.208,2.073 0.125,0.177 10 true B 1.813,1.896 1.938,2.073 0.125,0.177 10 true B 1.573,1.188 1.698,1.365 0.125,0.177 10 true B 1.323,1.302 1.448,1.479 0.125,0.177 10 true B 1.615,1.365 1.74,1.542 0.125,0.177 10 true B 1.208,1.854 1.333,2.031 0.125,0.177 10 true B 1.156,2.021 1.281,2.198 0.125,0.177 10 true B 0.792,1.427 0.917,1.604 0.125,0.177 10 false C 2.958,1.24 3.083,1.417 0.125,0.177 10 true D 2.51,0.99 2.635,1.167 0.125,0.177 10 true D 0.948,1.531 1.073,1.708 0.125,0.177 10 false D 2.542,1.781 2.667,1.958 0.125,0.177 10 false B 2.646,2.188 2.833,2.354 0.188,0.167 10 false *1 1.24,2.448 1.427,2.615 0.188,0.167 10 false *1 6.688,1.396 6.875,1.563 0.188,0.167 10 false *a 4.167,1.427 4.333,1.594 0.167,0.167 10 false *a 5.094,1.167 5.271,1.354 0.177,0.188 10 false *b 4.438,2.094 4.604,2.26 0.167,0.167 10 false *c 6.448,2.125 6.615,2.292 0.167,0.167 10 false *c 6.979,0.823 7.146,0.99 0.167,0.167 10 false *d 3.865,0.792 4.031,0.958 0.167,0.167 10 false *d 6.094,0.135 6.26,0.302 0.167,0.167 10 false *d

Text in Illustration
*1 Nut - -
*a Area 1 *b Area 2
*c Area 3 *d Area 4

NOTICE:

Make sure that there is no oil on the bolt threads.



h.

Tighten the bolts in area 1.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)

HINT:

Tighten the bolts from bottom to top as shown in the illustration.



i.

Tighten the bolts in area 2.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


j.

Tighten the bolts in area 3.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

HINT:

Tighten the bolts and nuts from top to bottom as shown in the illustration.



k.

Tighten the bolts in area 4.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)

HINT:

Tighten the bolts from bottom to top as shown in the illustration.


NOTICE:
·

Do not start the engine for at least 2 hours after installation.

·

Wipe off any seal packing that seeped out around the surfaces of the oil pan and cylinder head cover and make sure that there is no seal packing seeping out around the edges.




Hide 12101 3.INSTALL OIL PAN SUB-ASSEMBLY

a.

Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder block, rear oil seal retainer and oil pan.


b.

Install a new 3 O-rings to the timing chain cover sub-assembly.


c.
A222121E03
1.448,0.417 1.635,0.417 1.635,0.417 2.052,1.021 true 1.25,0.333 1.417,0.531 0.167,0.198 10 false *1

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the oil pan within 3 minutes after applying seal packing.




d.
A223671E04
0.271,2.01 0.396,2.177 0.125,0.167 10 false A 0.271,1.688 0.396,1.854 0.125,0.167 10 false A 0.26,1.365 0.385,1.531 0.125,0.167 10 true A 0.885,0.479 1.01,0.646 0.125,0.167 10 true A 1.167,2.573 1.344,2.781 0.177,0.208 10 true B 1.5,2.563 1.698,2.729 0.198,0.167 10 true B 2.333,2.531 2.542,2.75 0.208,0.219 10 true B 3.01,2.156 3.135,2.323 0.125,0.167 10 false B 2.615,0.51 2.74,0.677 0.125,0.167 10 true B 2.26,0.531 2.385,0.698 0.125,0.167 10 true B 1.188,0.552 1.313,0.719 0.125,0.167 10 true C 1.49,0.531 1.615,0.698 0.125,0.167 10 true C 1.719,0.469 1.844,0.635 0.125,0.167 10 true C 1.917,0.542 2.042,0.708 0.125,0.167 10 true C 3.188,1.385 3.313,1.552 0.125,0.167 10 false D 3.188,1.708 3.313,1.875 0.125,0.167 10 false D 0.271,1.042 0.396,1.208 0.125,0.167 10 false E 1.646,1.875 1.813,2.042 0.167,0.167 10 true *1 0.625,2.531 0.844,2.729 0.219,0.198 10 true *1

Install the oil pan sub-assembly with the 17 bolts (A, B, C, D and E) and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
for bolt A, B, C and E, and nut : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt D : 10 N*m (102 kgf*cm, 7 ft.*lbf)

Standard Bolt:
Item Length
Bolt A 60 mm (2.36 in.)
Bolt B 45 mm (1.77 in.)
Bolt C 25 mm (0.984 in.)
Bolt D 16 mm (0.630 in.)
Bolt E 70 mm (2.76 in.)


Text in Illustration
*1 Nut

NOTICE:

Do not start the engine for at least 2 hours after installing.



Hide 15104 4.INSTALL OIL STRAINER SUB-ASSEMBLY

a.

Install a new gasket and the oil strainer sub-assembly with the 2 nuts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 12102A 5.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.
A174349E04
0.979,0.542 1.229,0.542 1.229,0.542 1.542,1.052 true 0.76,0.458 0.948,0.646 0.188,0.188 10 false *1

Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

3.0 to 4.0 mm (0.118 to 0.157 in.)


Text in Illustration
*1 Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the No. 2 oil pan sub-assembly within 3 minutes after applying seal packing.




b.
A225446

Install the No. 2 oil pan sub-assembly with the 10 bolts and 2 nuts. Tighten the bolts and nuts uniformly in several steps.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

Text in Illustration
V100135

Bolt
V100136

Nut

NOTICE:
·

Tighten the nuts first. After tightening the bolts, check that the nuts and bolts are tightened to the specified torque.

·

Do not start the engine for at least 2 hours after the installation.




Hide 11201 6.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover sub-assembly and cylinder head cover sub-assembly.


b.
A223667

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.

Install 3 new gaskets.


d.

Install a new gasket to the cylinder head cover sub-assembly.


e.

Install the seal washers to the bolts.


f.
A225447E05
1.469,0.74 1.865,0.917 0.396,0.177 10 true 1, 11 2.49,0.021 2.615,0.208 0.125,0.188 10 true 2 1.552,1.99 1.677,2.135 0.125,0.146 10 true 3 0.219,0.24 0.406,0.427 0.188,0.188 10 true 4 1.958,0.094 2.083,0.281 0.125,0.188 10 true 6 2.083,1.99 2.292,2.135 0.208,0.146 10 true 10 0.708,2.01 0.917,2.156 0.208,0.146 10 false 12 0.073,1.104 0.281,1.25 0.208,0.146 10 false 13 1.167,0.094 1.354,0.281 0.188,0.188 10 true 5 3.198,0.167 3.375,0.396 0.177,0.229 10 true 7 3.25,0.99 3.427,1.219 0.177,0.229 10 true 8 3.198,1.646 3.375,1.875 0.177,0.229 10 true 9

Temporarily install the cylinder head cover sub-assembly with the 12 bolts. Tighten the bolts uniformly in several steps.

Torque:
for bolt A and D : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B and C : 21 N*m (214 kgf*cm, 15 ft.*lbf)

Standard Bolt:
Item Length
A 25 mm (0.984 in.)
B 35 mm (1.38 in.)
C 65 mm (2.56 in.)
D 60 mm (2.36 in.)


Text in Illustration
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D

NOTICE:

Do not start the engine for at least 2 hours after installation.



Hide 11202 7.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY LH

a.

Remove any old packing (FIPG material) and be careful not to drop any oil on the contact surfaces of the cylinder head, timing chain cover sub-assembly and cylinder head cover sub-assembly LH.


b.
A223664

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

2.0 to 3.0 mm (0.0787 to 0.118 in.)


Text in Illustration
V100135

Seal Packing

NOTICE:
·

Remove any oil from the contact surface.

·

Install the cylinder head cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.

Install 3 new gaskets.


d.

Install a new gasket to the cylinder head cover sub-assembly LH.


e.

Install the seal washers to the bolts.


f.
A226494E06
1.854,0.688 2.26,0.896 0.406,0.208 10 true 1, 10 0.948,0 1.073,0.188 0.125,0.188 10 false 2 3.177,1.792 3.302,1.938 0.125,0.146 10 false 3 2.229,1.927 2.354,2.115 0.125,0.188 10 false 4 0.188,0.073 0.313,0.26 0.125,0.188 10 false 6 1.615,0.052 1.74,0.24 0.125,0.188 10 false 7 2.385,0.042 2.51,0.229 0.125,0.188 10 false 8 3.302,0.229 3.427,0.417 0.125,0.188 10 true 9 0.563,1.979 0.979,2.146 0.417,0.167 10 false 11, 14 0.156,1.833 0.365,1.979 0.208,0.146 10 false 12 1.24,1.958 1.448,2.104 0.208,0.146 10 false 13 0.052,1.083 0.26,1.229 0.208,0.146 10 false 5

Temporarily install the cylinder head cover sub-assembly LH with the 12 bolts. Tighten the bolts uniformly in several steps.

Torque:
for bolt A and D : 10 N*m (102 kgf*cm, 7 ft.*lbf)
for bolt B and C : 21 N*m (214 kgf*cm, 15 ft.*lbf)

Standard Bolt:
Item Length
A 25 mm (0.984 in.)
B 35 mm (1.38 in.)
C 70 mm (2.76 in.)
D 60 mm (2.36 in.)


Text in Illustration
V100135

Bolt A
V100136

Bolt B
V100137

Bolt C
V100138

Bolt D

NOTICE:

Do not start the engine for at least 2 hours after installation.



Hide 8.CONNECT FUEL PIPE SUB-ASSEMBLY

a.

Connect the fuel pipe sub-assembly with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


Hide 11181A 9.INSTALL REAR CYLINDER HEAD COVER

Hide 15772 10.INSTALL NO. 2 OIL PIPE

a.

Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

NOTICE:

Do not touch the mesh when installing the oil control valve filter.



b.

Install a new gasket and temporarily install the No. 2 oil pipe (on the cylinder head side) with the oil check valve bolt.


c.

Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the No. 2 oil pipe (on the head cover side).


d.

Tighten the oil pipe union (on the cylinder head side).

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)

NOTICE:

If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.



e.

Tighten the oil pipe union (on the head cover side).

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


Hide 15771 11.INSTALL NO. 1 OIL PIPE

a.

Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

NOTICE:

Do not touch the mesh when installing the oil control valve filter.



b.

Install a new gasket and temporarily install the No. 1 oil pipe (on the cylinder head side) with the oil check valve bolt.


c.

Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the No. 1 oil pipe (on the head cover side).


d.

Tighten the oil pipe union (on the cylinder head side).

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)

NOTICE:

If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.



e.

Tighten the oil pipe union (on the head cover side).

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


Hide 13471 12.INSTALL CRANKSHAFT PULLEY

a.
A076309E09
1.438,1.083 2.948,0.948 2.948,0.948 2.135,1.469 true 3.021,0.844 3.354,1 0.333,0.156 10 false SST

Using SST, install the crankshaft pulley with the pulley set bolt.

SST
09213-54015  (91651-60855)
09330-00021  

Torque:
260 N*m (2651 kgf*cm, 192 ft.*lbf)


Hide 15671 13.INSTALL OIL FILTER BRACKET

a.

Install the oil filter bracket and a new gasket with the 2 nuts and bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16620 14.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.
A226495E07
2,0.5 2.208,0.385 2.208,0.385 2.323,0.385 true 2.156,1.458 2.49,1.115 2.49,1.115 2.604,1.115 true 2.333,0.292 2.458,0.479 0.125,0.188 10 true 1 2.656,1.042 2.844,1.26 0.188,0.219 10 true 2

Temporarily install the V-ribbed belt tensioner assembly with the 5 bolts.

Standard Bolt:
Item Length
A 70 mm (2.76 in.)
B 33 mm (1.30 in.)


Text in Illustration
V100135

Bolt A
V100136

Bolt B


b.

Tighten bolts 1 and 2 in numerical order.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


c.

Tighten the other bolts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)


Hide 16604 15.INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

Hide 16603 16.INSTALL NO. 1 IDLER PULLEY SUB-ASSEMBLY

a.
A076438E09
2.49,1.802 3.271,2 0.781,0.198 10 false "DOUBLE"

Install the No. 1 idler pulley sub-assembly with the bolt.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)

HINT:

"DOUBLE" is marked on the No. 1 idler pulley to distinguish it from the No. 2 idler pulley.



Hide 16323 17.INSTALL WATER INLET HOUSING

a.

Install the 3 water by-pass hoses.


b.

Apply soapy water to a new O-ring and install the O-ring to the water outlet pipe.


c.

Install a new O-ring to the water outlet pipe.


d.

Install a new gasket to the water pump assembly.


e.

Install the water inlet with the 5 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Connect the 3 water by-pass hoses.


Hide 16206 18.INSTALL WATER BY-PASS PIPE SUB-ASSEMBLY

a.
A223698E06
0.49,2.458 0.677,2.635 0.188,0.177 10 true *a 0.115,2.969 0.302,3.146 0.188,0.177 10 false *b

Install the water by-pass pipe sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the 2 hoses.

HINT:

The direction of the hose clamp is indicated in the illustration.


Text in Illustration
*a Upward
*b Rearward


Hide 11452 19.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.
A223631E02
2.49,1.365 2.406,1.365 2.406,1.365 2.292,1.417 false 2.521,1.271 2.698,1.448 0.177,0.177 10 false *1

Install a new O-ring to the engine oil level dipstick guide.

Text in Illustration
*1 New O-Ring


b.

Apply a light coat of engine oil to the O-ring.


c.

Push the engine oil level dipstick guide end into the guide hole.


d.

Install the engine oil level dipstick guide with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Install the engine oil level dipstick.


Hide 25702B 21.INSTALL NO. 2 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 25701B 22.INSTALL NO. 1 EMISSION CONTROL VALVE SET (w/ Secondary Air Injection System)

Hide 23.INSTALL ENGINE ASSEMBLY