12281A
1.INSTALL ENGINE HANGER
Install 2 engine hangers with 4 bolts as shown in the illustration.
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
| No. 1 Engine Hanger | 12281-31110 |
| No. 2 Engine Hanger | 12282-31140 |
| Bolt | 91671-C0830 |
2.REMOVE ENGINE STAND
Attach an engine sling device and hang the engine with a chain block.
Lift the engine and remove it from the engine stand.
Place the engine onto a work bench.
3.INSTALL ENGINE ASSEMBLY
Attach an engine sling device and hang the engine with a chain block.
Slowly lower the engine into the engine compartment.
Install the front engine mounting insulator LH with the 3 nuts and 2 bolts.
Install the front engine mounting insulator RH with the 3 nuts and 2 bolts.
Remove the 4 bolts and 2 engine hangers.
32101
4.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY
Using SST, hold the crankshaft.
Install the front spacer, drive plate and rear spacer to the crankshaft.
| *1 | Front Spacer |
| *2 | Drive Plate and Ring Gear Sub-assembly |
| *3 | Rear Spacer |
|
Automatic Transmission Side |
As the front spacer, drive plate and ring gear and rear spacer are not reversible, be sure to install it in the direction shown in the illustration.
Apply adhesive to 2 or 3 threads at the end of the 8 bolts.
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Uniformly install and tighten the 8 bolts in several steps in the sequence shown in the illustration.
Do not start the engine for at least 1 hour after installing.
35000
5.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY
6.INSTALL PROPELLER SHAFT ASSEMBLY (for 4WD)
7.INSTALL PROPELLER SHAFT ASSEMBLY (for 2WD)
8.INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)
23801P
9.CONNECT NO. 1 AND NO. 2 FUEL PIPES
Connect the No. 1 and No. 2 fuel pipes (See page Engine / Hybrid System>1GR-FE FUEL>FUEL SYSTEM>PRECAUTION).
Install the No. 2 fuel pipe clamp to the fuel tube connector.
10.CONNECT HEATER WATER HOSE ASSEMBLY
Connect the 2 hoses and heater water hose assembly.
| *a | Top |
| *b | LH |
The direction of the hose clamp is indicated in the illustration.
82121
11.CONNECT ENGINE WIRE
Connect the ECM connector.
Attach the grommet to the wire harness support.
| *1 | Grommet |
| *2 | Wire Harness Support |
Pass the wire harness into the vehicle and install the wire harness support.
Connect the 6 connectors and attach the clamp.
for 4WD:
Attach the clamp and connect the connector.
Connect the connector and install the bolt.
55303B
12.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY
11363A
13.INSTALL FLYWHEEL HOUSING SIDE COVER
28100
14.INSTALL STARTER ASSEMBLY
28192
15.INSTALL STARTER COVER
27020
16.INSTALL GENERATOR ASSEMBLY
82715
17.INSTALL WIRING HARNESS CLAMP BRACKET
17105
18.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY LH
17168
19.INSTALL NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
17362
20.INSTALL NO. 2 AIR TUBE (w/ Secondary Air Injection System)
17119
21.INSTALL NO. 2 MANIFOLD STAY
17104
22.INSTALL EXHAUST MANIFOLD SUB-ASSEMBLY RH
17167
23.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17361
24.INSTALL AIR TUBE (w/ Secondary Air Injection System)
17118
25.INSTALL MANIFOLD STAY
17410
26.INSTALL FRONT EXHAUST PIPE ASSEMBLY
88320
27.INSTALL COOLER COMPRESSOR ASSEMBLY
88704
28.CONNECT SUCTION HOSE SUB-ASSEMBLY
88703
29.CONNECT DISCHARGE HOSE SUB-ASSEMBLY
44310
30.CONNECT VANE PUMP ASSEMBLY
31.INSTALL FAN AND GENERATOR V BELT
17129
32.INSTALL INTAKE AIR SURGE TANK
17360G
33.INSTALL AIR TUBE ASSEMBLY (w/ Secondary Air Injection System)
16400
34.INSTALL RADIATOR ASSEMBLY
16711
35.INSTALL FAN SHROUD
32907C
36.CONNECT OIL COOLER TUBE
16470
37.INSTALL RADIATOR RESERVOIR TANK
16572
38.INSTALL NO. 2 RADIATOR HOSE
16571
39.INSTALL NO. 1 RADIATOR HOSE
53294C
40.INSTALL RADIATOR SIDE DEFLECTOR LH
53293C
41.INSTALL RADIATOR SIDE DEFLECTOR RH
52521
42.INSTALL UPPER CENTER FRONT BUMPER RETAINER
43.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
Install the air cleaner case sub-assembly with the 3 bolts.
Attach the wire harness clamp.
Install the air cleaner filter element sub-assembly.
44.INSTALL AIR CLEANER CAP AND HOSE
52119A
45.INSTALL FRONT BUMPER COVER
w/o TOYOTA Parking Assist-sensor System: (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER>INSTALLATION)
w/ TOYOTA Parking Assist-sensor System: (See page Vehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER(w/ TOYOTA Parking Assist-sensor System)>INSTALLATION)
11259
46.INSTALL V-BANK COVER
74431
47.INSTALL BATTERY TRAY
28800
48.INSTALL BATTERY
74481A
49.INSTALL BATTERY HOLD DOWN CLAMP
28800A
50.CONNECT CABLE TO POSITIVE BATTERY TERMINAL
51.ADD ENGINE COOLANT
52.ADD ENGINE OIL
55781E
53.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
54.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
55.INSPECT FOR FUEL LEAK
56.INSPECT FOR ENGINE OIL LEAK
57.INSPECT FOR EXHAUST GAS LEAK
58.CHECK ENGINE OIL LEVEL
53292A
59.INSTALL UPPER RADIATOR SUPPORT SEAL
Install the upper radiator support seal with the 13 clips.
53736B
60.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
53737A
61.INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL LH
53736
62.INSTALL FRONT FENDER APRON SEAL RH
53737B
63.INSTALL FRONT FENDER APRON SEAL LH
51450
64.INSTALL REAR ENGINE UNDER COVER ASSEMBLY
Install the rear engine under cover assembly with the 4 bolts.
51495
65.INSTALL TRANSMISSION UNDER COVER
Install the transmission under cover with the 2 bolts.
51405A
66.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Hook the No. 1 engine under cover sub-assembly to the vehicle body as shown in the illustration.
Install the 4 bolts.
52129B
67.INSTALL FRONT BUMPER LOWER COVER (w/o TOYOTA Parking Assist-sensor System)
Install the front bumper lower cover with the 5 bolts and clip.
52822
68.INSTALL AIR INTAKE DUCT LH (w/ TOYOTA Parking Assist-sensor System)
Install the air intake duct LH with the 2 screws.
Install the clip and bolt.
52821
69.INSTALL AIR INTAKE DUCT RH (w/ TOYOTA Parking Assist-sensor System)
Use the same procedure as for the LH side.
52129B
70.INSTALL FRONT BUMPER LOWER COVER (w/ TOYOTA Parking Assist-sensor System)
Install the front bumper lower cover with the 4 bolts and clip.
53298
71.INSTALL COOL AIR INTAKE DUCT (for 4WD with TOYOTA Parking Assist-sensor System)
72.PERFORM RESET MEMORY
73.INSPECT IGNITION TIMING
74.INSPECT ENGINE IDLE SPEED
53301
76.INSTALL HOOD SUB-ASSEMBLY
Install the hood sub-assembly with the 8 bolts.
|
Bolt A |
|
Bolt B |
Connect the washer nozzle hose.
53301
77.ADJUST HOOD SUB-ASSEMBLY
78.CHARGE REFRIGERANT
79. WARM UP ENGINE
80.CHECK FOR REFRIGERANT GAS LEAK