Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2010.08
RM1440E _54 Brake _056142 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0274004 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1251  Open in Pump Motor Circuit  


DESCRIPTION

The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU.

DTC Code DTC Detection Condition Trouble Area
C1251 There is an open in the motor system circuit (motor input circuit).
·

Pump motor wire harness connection

·

Brake booster with accumulator pump assembly

·

Master cylinder solenoid (Skid control ECU)



CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).


HINT:

Remove the hydraulic brake booster assembly before the inspection (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER>ON-VEHICLE INSPECTION).


PROCEDURE

1.CHECK CONNECTION OF PUMP MOTOR WIRE HARNESS
a.

Remove the hydraulic brake booster assembly (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER>REMOVAL).


b.

Check the tightening torque of the 2 screws which secure the wire harness connecting the master cylinder solenoid and brake booster with accumulator pump assembly (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER>DISASSEMBLY).

OK:

The harness is tightened to the specified torque.


Torque:

2.9 N*m (30 kgf*cm, 26 in.*lbf)




OK

2.CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS

NG

RETIGHTEN SCREWS

2.CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS
a.

Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.


b.
C173363E14
1.531,1.438 0.885,0.771 0.885,0.771 0.708,0.771 true 1.375,1.479 0.875,1.792 0.875,1.792 0.708,1.792 false 1.594,1.813 2.104,0.844 2.104,0.844 2.292,0.844 true 0.5,0.667 0.76,0.917 0.26,0.25 10 false *a 0.51,1.698 0.708,1.906 0.198,0.208 10 false *b 2.365,0.76 2.646,0.969 0.281,0.208 10 false *1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Red wire terminal - Black wire terminal Always Below 2 Ω


Text in Illustration
*1 Pump motor wire harness
*a Red wire
*b Black wire



OK

3.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

3.RECONFIRM DTC
a.

Reassemble the hydraulic brake booster assembly (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER>REASSEMBLY).


b.

Install the hydraulic brake booster assembly (See page Brake>BRAKE SYSTEM (OTHER)>HYDRAULIC BRAKE BOOSTER>INSTALLATION).



d.

Turn the ignition switch off.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is output A
DTC is not output B



A

REPLACE MASTER CYLINDER SOLENOID

B