Home › Vehicle Interior › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM
RM1440E _58 Vehicle Interior _056155 DOOR LOCK _0274054 POWER DOOR LOCK CONTROL SYSTEM J

DOOR LOCK  POWER DOOR LOCK CONTROL SYSTEM  All Doors LOCK/UNLOCK Functions do not Operate Via Master Switch, Driver Side Door Key Cylinder  


DESCRIPTION

The main body ECU (multiplex network body ECU) receives switch signals from the multiplex network master switch, and key-linked switch signals from the front door lock. The main body ECU (multiplex network body ECU) activates the door lock motor on each door according to these signals.

WIRING DIAGRAM

B453537E01
1.396,0.438 1.531,0.604 0.135,0.167 10 false E 1.406,0.99 1.542,1.156 0.135,0.167 10 false L 1.323,1.531 1.531,1.698 0.208,0.167 10 false UL 1.604,0.448 1.729,0.604 0.125,0.156 10 false 7 1.604,0.969 1.74,1.146 0.135,0.177 10 false 9 1.594,1.542 1.813,1.708 0.219,0.167 10 false 10 2.365,0.958 2.583,1.125 0.219,0.167 10 false 11 2.365,1.531 2.583,1.698 0.219,0.167 10 false 24 2.708,1.104 2.906,1.292 0.198,0.188 10 false L2 2.688,1.646 2.979,1.823 0.292,0.177 10 false UL3 0.177,2.094 0.333,2.271 0.156,0.177 10 false I5 0.167,2.25 2.063,2.427 1.896,0.177 10 false Front Door Lock Assembly LH 1.406,2.969 1.542,3.135 0.135,0.167 10 false E 1.396,3.521 1.531,3.688 0.135,0.167 10 false L 1.333,4.073 1.542,4.24 0.208,0.167 10 false UL 1.635,2.979 1.76,3.135 0.125,0.156 10 false 3 1.646,3.51 1.771,3.667 0.125,0.156 10 false 4 1.635,4.063 1.76,4.219 0.125,0.156 10 false 2 2.438,3.521 2.573,3.688 0.135,0.167 10 false 9 2.417,4.073 2.594,4.229 0.177,0.156 10 false 10 0.115,4.615 0.354,4.792 0.24,0.177 10 false g2 0.094,4.802 2.021,5 1.927,0.198 10 false Door Control Switch Assembly 2.708,3.635 2.927,3.802 0.219,0.167 10 false L1 2.698,4.198 2.99,4.375 0.292,0.177 10 false UL1 2.198,5.188 2.417,5.354 0.219,0.167 10 false F9 2.208,5.365 3.896,5.75 1.688,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 5.458,1.417 7.083,1.823 1.625,0.406 10 false Power Window Regulator Master Switch Assembly 4.958,3.146 5.385,3.354 0.427,0.208 10 false KEYE 5.063,3.688 5.354,3.865 0.292,0.177 10 false BKL 4.99,4.219 5.375,4.396 0.385,0.177 10 false BKUL 5.49,3.021 5.625,3.188 0.135,0.167 10 false 8 5.49,3.552 5.698,3.729 0.208,0.177 10 false 16 5.49,4.115 5.688,4.281 0.198,0.167 10 false 15 5.896,3.01 6.031,3.177 0.135,0.167 10 false 3 5.896,3.521 6.021,3.698 0.125,0.177 10 false 1 5.885,4.104 6.021,4.271 0.135,0.167 10 false 2 6.104,2.99 6.25,3.156 0.146,0.167 10 false E 6.115,3.552 6.26,3.719 0.146,0.167 10 false L 6.094,4.104 6.313,4.281 0.219,0.177 10 false UL 4.135,4.979 4.469,5.156 0.333,0.177 10 false W10 4.135,5.177 5.646,5.531 1.51,0.354 10 false Multiplex Network Door ECU (Back Door P/W) 5.844,4.99 6.156,5.188 0.313,0.198 10 false W4 5.844,5.167 7.021,5.531 1.177,0.365 10 false Tail Gate Control Switch Assembly 0.74,6.396 2.375,6.594 1.635,0.198 10 false : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Since the power door lock control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.


PROCEDURE

1.CHECK DOOR LOCK OPERATION
a.

Check the door lock operation.

Result
Result Proceed to
No doors can be locked using multiplex network master switch A
No doors can be locked using door control switch B
No doors can be locked using key-linked switch C
No doors can be locked using tail gate control switch D



A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH)

C

5.READ VALUE USING INTELLIGENT TESTER (KEY-LINKED SWITCH)

D

8.READ VALUE USING INTELLIGENT TESTER (TAIL GATE CONTROL SWITCH)
2.READ VALUE USING INTELLIGENT TESTER (DOOR CONTROL SWITCH)
a.

Use the Data List to check if the door control switch is functioning properly (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DTC CHECK / CLEAR).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Door Lock SW-Lock Door control switch lock signal / ON or OFF ON: Lock side of door control switch pushed
OFF: Lock side of door control switch not pushed
-
Door Lock SW-Unlock Door control switch unlock signal / ON or OFF ON: Unlock side of door control switch pushed
OFF: Unlock side of door control switch not pushed
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT DOOR CONTROL SWITCH ASSEMBLY
3.INSPECT DOOR CONTROL SWITCH ASSEMBLY
a.
B240446E01
1.362,1.242 0.856,0.738 0.856,0.738 0.721,0.738 false 1.823,1.352 2.079,1.842 2.079,1.842 2.239,1.842 false 0.578,0.639 0.693,0.804 0.115,0.165 10 L 1.072,1.76 1.187,1.925 0.115,0.165 10 E 2.262,1.739 2.461,1.904 0.199,0.165 10 UL 1.62,1.352 1.365,1.842 1.365,1.842 1.205,1.842 false

Remove the door control switch (See page Vehicle Interior>DOOR LOCK>DOOR CONTROL SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (L) - 3 (E) Lock Below 1 Ω
4 (L) - 3 (E) Off 10 kΩ or higher
2 (UL) - 3 (E) Unlock Below 1 Ω
2 (UL) - 3 (E) Off 10 kΩ or higher




OK

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MAIN BODY ECU)

NG

REPLACE DOOR CONTROL SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (DOOR CONTROL SWITCH ASSEMBLY - MAIN BODY ECU)
a.

Disconnect the g2 door control switch connector.


b.

Disconnect the F9 main body ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
g2-2 (UL) - F9-10 (UL1) Always Below 1 Ω
g2-4 (L) - F9-9 (L1) Always Below 1 Ω
g2-3 (E) - Body ground Always Below 1 Ω
g2-2 (UL) - Body ground Always 10 kΩ or higher
g2-4 (L) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.READ VALUE USING INTELLIGENT TESTER (KEY-LINKED SWITCH)
a.

Use the Data List to check if the door key-linked switch is functioning properly (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Door Key SW-Lock Driver side door key-linked switch lock signal / ON or OFF ON: Driver side door key cylinder turned to lock position
OFF: Driver side door key cylinder not turned to lock position
-
D Door Key SW-UL Driver side door key-linked switch unlock signal / ON or OFF ON: Driver side door key cylinder turned to unlock position
OFF: Driver side door key cylinder not turned to unlock position
-

OK:

On tester screen, each item changes between ON and OFF according to above chart.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

6.INSPECT FRONT DOOR LOCK ASSEMBLY LH (KEY-LINKED SWITCH)
6.INSPECT FRONT DOOR LOCK ASSEMBLY LH (KEY-LINKED SWITCH)
a.

Remove the front door lock LH (See page Vehicle Interior>DOOR LOCK>FRONT DOOR LOCK>REMOVAL).

B241588E03
5.385,2.094 5.552,2.49 5.552,2.49 5.646,2.49 false 5.031,2.104 4.906,2.49 4.906,2.49 4.833,2.49 false 4.917,2.031 4.677,1.625 4.677,1.625 4.573,1.625 false 5.677,2.417 5.823,2.563 0.146,0.146 10 false E 4.74,2.417 4.844,2.563 0.104,0.146 10 false L 4.375,1.563 4.573,1.708 0.198,0.146 10 false UL

Text in Illustration
V100135

Lock
V100136

Unlock


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
9 (L) - 7 (E) Lock Below 1 Ω
9 (L) - 7 (E) Off 10 kΩ or higher
10 (UL) - 7 (E) Unlock Below 1 Ω
10 (UL) - 7 (E) Off 10 kΩ or higher




OK

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY LH - MAIN BODY ECU AND BODY GROUND)

NG

REPLACE FRONT DOOR LOCK ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK ASSEMBLY LH - MAIN BODY ECU AND BODY GROUND)
a.

Disconnect the I5 door lock connector.


b.

Remove the main body ECU connector. (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL)


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I5-10 (UL) - F9-24 (UL3) Always Below 1 Ω
I5-9 (L) - F9-11 (L2) Always Below 1 Ω
I5-7 (E) - Body ground Always Below 1 Ω
I5-10 (UL) - Body ground Always 10 kΩ or higher
I5-9 (L) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING INTELLIGENT TESTER (TAIL GATE CONTROL SWITCH)
a.

Use the Data List to check if the tail gate control switch and back door are functioning properly (See page Vehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

Back Door P/W
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Key Switch Operation Locked Tail gate control switch signal / ON or OFF ON: Back door key cylinder turned to lock position
OFF: Back door key cylinder not turned
-
Key Switch Operation Unlocked Tail gate control switch signal / ON or OFF ON: Back door key cylinder turned to unlock position
OFF: Back door key cylinder not turned
-
Back Door Courtesy Switch Back door courtesy switch signal / ON or OFF ON: Back door open
OFF: Back door closed
-

Result Proceed to
OK A
NG (Key Switch Operation Locked or Key Switch Operation Unlocked) B
NG (Back Door Courtesy Switch) C



A

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

B

9.INSPECT TAIL GATE CONTROL SWITCH ASSEMBLY

C

9.INSPECT TAIL GATE CONTROL SWITCH ASSEMBLY
a.

Remove the tail gate control switch (See page Vehicle Exterior>DOOR / HATCH>BACK DOOR>DISASSEMBLY).


B237565E01
1.937,1.183 2.358,0.603 2.358,0.603 2.487,0.603 false 1.522,1.183 1.101,0.603 1.101,0.603 0.972,0.603 false 0.853,0.521 0.964,0.670 0.111,0.149 10 L 2.516,1.768 2.627,1.917 0.111,0.149 10 E 2.516,0.529 2.718,0.678 0.203,0.149 10 UL 1.786,1.404 2.361,1.852 2.361,1.852 2.487,1.852 false

b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (L) - 3 (E) Lock position Below 1 Ω
1 (L) - 3 (E) Unlock position 10 kΩ or higher
2 (UL) - 3 (E) Unlock position Below 1 Ω
2 (UL) - 3 (E) Lock position 10 kΩ or higher




OK

10.CHECK HARNESS AND CONNECTOR (TAIL GATE CONTROL SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)

NG

REPLACE TAIL GATE CONTROL SWITCH ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (TAIL GATE CONTROL SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU)
a.

Disconnect the W4 tail gate control switch connector.


b.

Disconnect the W10 multiplex network door ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W4-1 (L) - W10-16 (BKL) Always Below 1 Ω
W4-2 (UL) - W10-15 (BKUL) Always Below 1 Ω
W4-3 (E) - W10-8 (KEYE) Always Below 1 Ω
W4-1 (L) - Body ground Always 10 kΩ or higher
W4-2 (UL) - Body ground Always 10 kΩ or higher




OK

REPLACE MULTIPLEX NETWORK DOOR ECU (BACK DOOR P/W)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR