Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1440E _58 Vehicle Interior _056158 METER / GAUGE / DISPLAY _0274083 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Meter Illumination is Always Dark  


DESCRIPTION

This inspection is only for vehicles with automatic light control.

The meter CPU receives signals from this circuit to adjust the illumination of the meter, instrument panel and accessory meter assembly. The meter CPU sets the illumination level based on the user operation of the light control rheostat.

HINT:
·

The meter illumination level can be adjusted by rotating the light control rheostat dial up and down.

·

The meter illumination dims when the light control switch is turned to the tail or head position at night.

·

Setting the meter illumination to maximum brightness cancels the above dimming of the meter illumination.



WIRING DIAGRAM

E200342E01
1.194,1.531 1.566,1.682 0.373,0.152 10 CLTB 1.194,2.114 1.566,2.295 0.372,0.181 10 CLTE 1.194,2.662 1.566,2.843 0.372,0.181 10 CLTS 1.634,1.526 1.819,1.678 0.185,0.152 10 20 1.634,2.098 1.819,2.250 0.185,0.152 10 22 1.634,2.651 1.819,2.803 0.185,0.152 10 21 3.622,1.546 3.994,1.698 0.373,0.152 10 CLTB 3.622,2.094 3.994,2.275 0.372,0.181 10 CLTE 3.622,2.647 3.994,2.828 0.372,0.181 10 CLTS 3.442,1.551 3.546,1.702 0.104,0.152 10 6 3.442,2.1 3.546,2.251 0.104,0.152 10 3 3.442,2.647 3.546,2.799 0.104,0.152 10 5 0.83,3.248 1.025,3.399 0.195,0.152 10 F9 0.829,3.397 1.851,3.568 1.021,0.171 10 Main Body ECU 3.571,3.27 4.569,3.581 0.997,0.310 10 Automatic Light Control Sensor 3.562,3.105 3.790,3.257 0.228,0.152 10 G2 5.051,3.258 6.904,3.415 1.853,0.156 10 Combination Meter Assembly 3.784,0.436 6.290,0.592 2.506,0.156 10 to each part that uses the dimmer signal 0.567,4.319 2.266,4.475 1.699,0.156 10 : CAN Communication Line

CAUTION / NOTICE / HINT

HINT:

Setting the meter illumination to minimum brightness turns off the meter illumination when the light control switch is changed to the tail or head position, or changed to the AUTO position at night.


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM).

Result
Result Proceed to
CAN communication DTC is not output A
CAN communication DTC is output B



A

2.CHECK DTC (LIGHT SENSOR CIRCUIT)

B

2.CHECK DTC (LIGHT SENSOR CIRCUIT)
a.

Check if DTC B1244 is output (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
B1244 is not output A
B1244 is output B



A

3.CHECK OPERATION (HEATER CONTROL PANEL)

B

3.CHECK OPERATION (HEATER CONTROL PANEL)
a.

Turn the ignition switch to ON.


b.

Turn the light control switch to the tail, head or AUTO position.


c.

Cover the automatic light control sensor.


d.

Check the heater control panel illumination.

Result
Result Proceed to
Heater control panel illumination does not operate normally A
Heater control panel illumination operates normally B

HINT:

Both the heater control panel and combination meter assembly illumination dim according to the dimmer signal. Therefore, when only the meter illumination is always dark, there may be a malfunction in the combination meter assembly.




A

4.CHECK OPERATION (AUTOMATIC LIGHT CONTROL SYSTEM)

B

REPLACE COMBINATION METER ASSEMBLY

4.CHECK OPERATION (AUTOMATIC LIGHT CONTROL SYSTEM)
a.

Turn the ignition switch to ON.


b.

Turn the light control switch to the AUTO position.


c.

Cover the automatic light control sensor.


d.

Check the taillights and low beam headlights.

OK:

The taillights and low beam headlights come on.



e.

Uncover the automatic light control sensor.


f.

Check the low beam headlights and taillights.

OK:

The taillights and low beam headlights go off.


Result
Result Proceed to
Automatic light control system operates normally A
Automatic light control system does not operate normally B



A

5.REPLACE MAIN BODY ECU

B

5.REPLACE MAIN BODY ECU
a.

Replace the main body ECU with a new or normally functioning one (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

OK:

The operation of the combination meter assembly returns to normal.


HINT:

The meter CPU controls the meter illumination based on an auto dimmer signal from the main body ECU. When the meter illumination is always dark (very dim), it may be due to the main body ECU sending an auto dimmer signal to the meter CPU because of a malfunction in the main body ECU.




OK

END

NG

REPLACE COMBINATION METER ASSEMBLY