Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT
RM1440E _58 Vehicle Interior _056163 HEATING / AIR CONDITIONING _0274138 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 55330B 1.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY

a.

Attach the 2 claws to install the instrument panel reinforcement assembly.


b.

Install the 5 bolts.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)


Hide 2.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT ASSEMBLY

a.

Install the instrument panel reinforcement assembly with air conditioning unit assembly.

i.

Install the bolts, nuts and instrument panel reinforcement assembly with air conditioning assembly.


ii.

Using a 12 mm hexagon wrench, install the 2 collars.


iii.

Using a T40 "TORX" socket, install the 5 "TORX" bolts.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


iv.

Install the 5 caps.

U150483E02
0.188,5.313 1.448,5.5 1.26,0.188 3.292,4.979 3.927,5.146 0.635,0.167 4.833,4.125 5.833,4.302 1,0.177 3.135,5.052 3.281,5.052 false 5.26,4.115 5.26,3.958 false 1.479,5.333 2.646,5.583 1.167,0.25 10 false : Specified torque 0.229,5.323 1.583,5.552 1.354,0.229 10 false N*m (kgf*cm, ft.*lbf) 3.302,5 3.927,5.135 0.625,0.135 8 false 20 (204, 15) 4.844,4.146 5.823,4.281 0.979,0.135 8 true 9.8 (100, 87 in.*lbf)



b.

Attach the clamps and connectors to the wire harness.

E197385


Hide 87201 3.INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY

a.

Attach the 3 claws to install the duct.


Hide 87201B 4.INSTALL NO. 2 AIR DUCT SUB-ASSEMBLY

a.

Attach the 3 claws to install the air duct.


b.

Install the screw.


Hide 55347A 5.INSTALL NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET LH

a.

Install the instrument panel brace mounting bracket LH with the 2 nuts and bolt.


Hide 55347A 6.INSTALL NO. 1 INSTRUMENT PANEL BRACE MOUNTING BRACKET RH

a.

Install the instrument panel brace mounting bracket RH with the 2 nuts and bolt.


Hide 58861B 7.INSTALL NO. 1 CONSOLE BOX DUCT

a.

Install the No. 1 console box duct with the clip.


Hide 87212G 8.INSTALL REAR NO. 3 AIR DUCT

a.

Attach the 3 clamps and 4 claws to install the rear No. 3 air duct.


Hide 87212 9.INSTALL REAR NO. 1 AIR DUCT

a.

Attach the 3 clamps and 4 claws to install the rear No. 1 air duct.


Hide 58510C 10.INSTALL FRONT FLOOR CARPET ASSEMBLY

a.

Install the front floor carpet assembly.


Hide 11.INSTALL FRONT SEAT ASSEMBLY LH

a.

for Manual Seat:

Install the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION).


b.

for Power Seat:

Install the front seat assembly LH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSTALLATION).


Hide 12.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


a.

for Manual Seat:

Install the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Manual Seat)>INSTALLATION).


b.

for Power Seat:

Install the front seat assembly RH (See page Vehicle Interior>SEAT>FRONT SEAT ASSEMBLY(for Power Seat)>INSTALLATION).


Hide 45250 13.INSTALL STEERING COLUMN ASSEMBLY

a.

Install the steering column assembly (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>INSTALLATION).


Hide 55301 14.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY

a.

Install the instrument panel sub-assembly (See page Vehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>INSTALLATION).


Hide 85110 15.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

a.

Install the windshield wiper motor assembly (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>INSTALLATION).


Hide 87245A 16.CONNECT HEATER WATER INLET HOSE AND HEATER WATER OUTLET HOSE

a.
U181036E02
0.615,2.25 2.833,3.344 2.219,1.094 0.906,2.833 1.677,2.833 false 1.292,2.458 1.292,3.271 false 1.875,2.833 2.656,2.833 false 2.271,2.458 2.271,3.26 false 1.042,2.844 0.865,2.979 0.865,2.979 0.865,3.125 false 2.229,3.115 2.177,3.198 2.177,3.198 1.927,3.198 false 0.677,2.302 0.865,2.469 0.188,0.167 10 false *a 0.5,2.031 0.656,2.24 0.156,0.208 10 true A 0.76,3.125 0.938,3.302 0.177,0.177 10 false *b 1.719,3.094 1.906,3.271 0.188,0.177 10 false *c

Connect the 2 heater water hoses.


b.

Using pliers, grip the claws of the clips and slide the 2 clips.

Text in Illustration
*a View A
*b Green Marking
*c Blue Marking


Hide 88710 17.CONNECT AIR CONDITIONING TUBE ASSEMBLY

E197374

a.

Install the grommet.


b.

Install the 2 O-rings to the air conditioning tube assembly.

Compressor oil:

ND-OIL 8 or equivalent



c.
E112921E04
0.708,0.292 0.896,0.479 0.188,0.188 10 false *a 2.26,0.302 2.448,0.479 0.188,0.177 10 false *b

Connect the air conditioning tube assembly with the piping clamp.

Text in Illustration
*a CORRECT
*b INCORRECT

NOTICE:

After the connection, check that the claw of the piping clamp is attached.



Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 19.CHECK SRS WARNING LIGHT

Hide 20.ADD ENGINE COOLANT