Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › from 2013.08
RM1440E _58 Vehicle Interior _056165 INTERIOR PANELS / TRIM _0274157 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).


PROCEDURE

Hide 55301 1.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY

a.

Attach the 2 guides to install the instrument panel sub-assembly.


b.

Connect each connector and attach the clamps and claws.


c.

Install the 2 passenger airbag bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


d.

Install the bolt labeled A.


e.

Install the 6 bolts <E> and nut <F>.

B360823E02
2.271,0.531 2.448,0.677 0.177,0.146 10 false *3 0.656,2.635 0.833,2.781 0.177,0.146 10 false *1 4.958,1.521 5.135,1.667 0.177,0.146 10 false *1 5.719,2.781 5.896,2.927 0.177,0.146 10 false *1 4.823,4.615 5,4.76 0.177,0.146 10 false *1 2.802,5.25 2.979,5.396 0.177,0.146 10 false *1 1.417,5.208 1.594,5.354 0.177,0.146 10 true *1 2.313,4.781 2.5,4.958 0.188,0.177 10 true *2 5.729,4.635 5.906,4.781 0.177,0.146 10 false *4 6.729,4.625 6.906,4.771 0.177,0.146 10 false *4 5.906,2.021 6.083,2.167 0.177,0.146 10 false *5

Text in Illustration
*1 Bolt <E> *2 Nut <F>
*3 Guide *4 Passenger Airbag Bolt
*5 Bolt A - -


Hide 89533A 2.INSTALL 4 WHEEL DRIVE CONTROL ECU NO.2 (for 4WD)

Hide 55408F 4.INSTALL NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.

Attach the 2 clips, 4 claws and 3 guides to install the No. 1 instrument panel speaker panel sub-assembly.


Hide 55409F 5.INSTALL NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.

Attach the 2 clips, 3 claws and 3 guides to install the No. 2 instrument panel speaker panel sub-assembly.


Hide 55650 6.INSTALL NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.

Attach the 4 clips and 2 guides to install the No. 1 instrument panel register assembly.


Hide 55660 7.INSTALL NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

HINT:

Use the same procedure as for the No. 1 instrument panel register assembly.


Hide 55406B 8.INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Climate Control Seat System)

a.

Connect each connector.


b.

Attach the 4 clips to install the lower center instrument cluster finish panel sub-assembly.


c.

Install the 2 screws <B>.


Hide 55406B 9.INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/ Climate Control Seat System)

a.

Connect each connector.


b.

Attach the 4 clips to install the lower center instrument cluster finish panel sub-assembly.


c.

Install the 2 screws <B>.


Hide 86140A 10.INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKETS (w/ Audio)

Hide 55424C 11.INSTALL RADIO TUNER FINISH PANEL (w/o Audio)

a.

Connect the connector.


b.

Attach the 6 clips to install the radio tuner finish panel.


c.

Install the 4 bolts.


Hide 55303B 13.INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY

a.

Connect each connector.


b.

Attach the 10 clips and guide to install the lower instrument panel sub-assembly.


c.

Install the 3 screws <B> and 2 bolts <C>.


Hide 55443A 14.INSTALL INSTRUMENT PANEL BOX DOOR COVER

a.

Attach the 2 claws and 2 guides to install the instrument panel box door cover.

HINT:

Use the same procedure for all the instrument panel box door covers.



Hide 55312 15.INSTALL LOWER INSTRUMENT PANEL

a.

Attach the 4 clips to install the lower instrument panel.


b.

Install the 2 bolts <D>.


Hide 55607 16.INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.

Attach the 3 clips and 2 guides to install the No. 2 instrument panel under cover sub-assembly.


Hide 55045 17.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

a.

Connect each connector and the hood lock control cable assembly.


b.

Attach the 6 clips and 2 guides to install the lower instrument panel finish panel sub-assembly.


c.

Install the 2 bolts <C>.


d.

Attach the 2 claws to close the cover.


Hide 55404D 19.INSTALL INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.

Attach the 7 clips to install the instrument cluster finish panel sub-assembly.


Hide 55447C 20.INSTALL NO. 2 SWITCH HOLE BASE

a.

Connect each connector.


b.

Attach the 6 clips and 2 guides to install the No. 2 switch hole base.


Hide 55480D 21.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.

Connect the cooler thermistor.


b.

Attach the 4 clips to install the lower instrument panel finish panel assembly.


Hide 62312B 26.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62311B 27.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure as for the LH side.


Hide 62111C 29.INSTALL COWL SIDE TRIM BOARD RH

HINT:

Use the same procedure as for the LH side.


Hide 67920 30.INSTALL DOOR SCUFF PLATE ASSEMBLY LH

Hide 67910 31.INSTALL DOOR SCUFF PLATE ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 58910C 32.INSTALL REAR CONSOLE BOX ASSEMBLY

Hide 84140 33.INSTALL HEADLIGHT DIMMER SWITCH ASSEMBLY

Hide 34.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).