Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR › 2009.08–2012.08
RM1440E _59 Vehicle Exterior _056168 DOOR / HATCH _0274180 BACK DOOR A

DOOR / HATCH  BACK DOOR  REASSEMBLY  


PROCEDURE

Hide 68946 1.INSTALL BACK DOOR UPPER DAMPER STAY BRACKET LH

Hide 68945 2.INSTALL BACK DOOR UPPER DAMPER STAY BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 68961 3.INSTALL BACK DOOR STAY BOLT (for LH Side)

Hide 68961 4.INSTALL BACK DOOR STAY BOLT (for RH Side)

HINT:

Use the same procedure described for the LH side.


Hide 68908 5.INSTALL BACK DOOR DAMPER STAY SUB-ASSEMBLY LH

Hide 68907 6.INSTALL BACK DOOR DAMPER STAY SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 67005B 7.INSTALL BACK DOOR PANEL CUSHION

a.

Attach the claw to install the 2 back door panel cushions.


Hide 67281F 8.INSTALL BACK DOOR LOWER STOPPER

a.

Install the lower stopper cushion with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Use the same procedure described for the LH side.



Hide 84840G 10.INSTALL BACK DOOR OPENER SWITCH ASSEMBLY

a.
B240243

Install the back door opener switch assembly with the 2 screws.


b.

Attach the guide and connect the connector.


Hide 86790D 11.INSTALL REAR TELEVISION CAMERA ASSEMBLY (w/ Rear View Monitor System)

Hide 76827A 13.INSTALL NO. 2 BACK DOOR GARNISH RETAINER (w/o Rear View Monitor System)

a.

Attach the 2 claws to install the No. 2 back door garnish retainer.


Hide 69055B 14.INSTALL BACK DOOR LOCK CYLINDER

a.

Install the lock cylinder with the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Connect the connector.


Hide 85720E 15.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69807 16.INSTALL BACK DOOR POWER WINDOW REGULATOR SUB-ASSEMBLY

a.

Apply MP grease to the sliding and rotating parts of the window regulator.


b.

Install the power regulator sub-assembly with the 5 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

Do not drop the back door power window regulator sub-assembly as it may be damaged.



c.

Connect the window regulator connector.


Hide 69350 17.INSTALL BACK DOOR LOCK ASSEMBLY

Hide 68290A 18.INSTALL OUTER BACK DOOR GLASS WEATHERSTRIP ASSEMBLY

Hide 68131 19.INSTALL BACK DOOR GLASS

a.

Temporarily connect the multiplex network body ECU connectors.


b.

Connect the cable to the negative (-) battery terminal.


c.

Move the back door glass until the bracket can be seen through the service holes.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



e.

Disconnect the multiplex network body ECU connectors.


f.
B240226E02
2.435,0.313 2.648,0.511 0.214,0.198 10 (1) 1.603,0.891 1.817,1.089 0.214,0.198 10 (2)

Insert the door glass as shown in the illustration.

NOTICE:

Do not damage the glass.



g.
B240222

Install the door glass with the 4 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


h.
B240223

B246228E02
2.583,1.313 2.583,1.385 true 0.844,1.563 0.844,1.854 0.844,1.854 1.042,1.854 true 0.979,1.354 1.167,1.063 1.167,1.063 1.354,1.063 true 0.698,1.354 0.5,1.073 0.5,1.073 0.313,1.073 true 2.583,1.552 2.583,1.625 true 2.583,1.427 2.583,1.5 true 2.583,1.667 2.583,1.729 true 2.552,1.115 2.677,1.292 0.125,0.177 10 false a 2.552,1.708 2.677,1.885 0.125,0.177 10 false a 0.635,0.875 1.031,1.052 0.396,0.177 10 false a - a 1.063,1.76 1.302,1.938 0.24,0.177 10 false *1 1.385,1 1.625,1.177 0.24,0.177 10 false *2 0.115,1 0.354,1.177 0.24,0.177 10 false *2

Connect the 2 rear window defogger connectors and install the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

NOTICE:

If the SUS plate is bent, broken, etc., replace the wire harness.


Text in Illustration
*1 SUS Plate
*2 Wire Harness


i.
B240221

Install the hole plug.


Hide 68275 20.INSTALL BACK DOOR GLASS RUN

a.
B240220

Install a new back door glass run.


Hide 67381A 21.INSTALL NO. 1 BACK WINDOW WIPER MOTOR BRACKET

a.
E199085

Attach the 2 clips to install the No. 1 back window wiper motor bracket.


b.

Install the 3 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 85293A 22.INSTALL REAR WIPER STOPPER

a.
E200707

Attach the claw and guide to install the linear wiper step.


Hide 85120R 24.INSTALL REAR WIPER MOTOR AND BRACKET ASSEMBLY

Hide 76085 26.INSTALL REAR SPOILER SUB-ASSEMBLY

Hide 76893 27.INSTALL REAR NO. 1 SPOILER COVER

Hide 67848 30.INSTALL BACK DOOR SERVICE HOLE COVER LH

a.
B240218

Attach the 2 clips to install the back door service hole cover.


b.

Install the 5 screws.


c.

Attach the clamp to install the wire harness.


Hide 67847 31.INSTALL BACK DOOR SERVICE HOLE COVER RH

a.
B240219

Attach the 2 clips to install the back door service hole cover.


b.

Install the 5 screws.


c.

Attach the clamp to install the wire harness.


Hide 67848C 32.INSTALL NO. 2 BACK DOOR SERVICE HOLE COVER

a.

Apply butyl tape to the back door panel.


b.
B240232E02
0.49,0.302 0.719,0.521 0.229,0.219 10 false *1 2.729,0.313 2.958,0.531 0.229,0.219 10 false *1

Install a new No. 2 back door service hole cover.

Text in Illustration
*1 Reference Point


c.

Attach the No. 2 back door service hole cover according to the reference points on the back door panel.

NOTICE:

Securely install the back door service hole cover preventing wrinkles and air bubbles.



Hide 89222A 33.INSTALL MULTIPLEX NETWORK DOOR ECU

a.
B242094

Attach the 2 clips to install the multiplex network door ECU to the door panel.


b.
B242093

Install the 3 screws.


c.
B242092

Connect the 3 connectors and attach the 2 clamps.


Hide 86160Y 34.INSTALL REAR NO. 2 SPEAKER ASSEMBLY

Hide 68291 35.INSTALL BACK DOOR GLASS WEATHERSTRIP

a.
B242125

Install a new back door glass weatherstrip on the back door trim board assembly and fold down the 9 claws as shown in the illustration.


Hide 64780A 36.INSTALL BACK DOOR TRIM PANEL ASSEMBLY

a.

Attach the 12 clips to install the back door trim board assembly.


Hide 69308 37.INSTALL BACK DOOR LOCK PROTECTOR SUB-ASSEMBLY

a.

Attach the 2 claws to install the back door lock protector.


Hide 74811G 38.INSTALL DOOR PULL HANDLE

a.

Attach the 4 claws to install the back door pull handle.

HINT:

Use the same procedure for all back door pull handles.