Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

SMART KEY SYSTEM (for Entry Function) > All Door Entry Lock/Unlock Functions do not Operate, but Wireless Functions Operate

for Preparation Click here


DESCRIPTION

When the wireless operation can be used to lock and unlock the doors, the communication line between the door control receiver and certification ECU is normal. When the entry operation does not operate, one of the following may be the cause: 1) the entry cancel function is set through customization; 2) there is a malfunction in the smart key system communication line (electrical key transmitter and vehicle); or 3) there is wave interference.

INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.
  3. Check that there are no electrical key transmitters in the vehicle.
  4. Before performing the inspection, check that DTC B1242 (wireless door lock control) is not output (Click here).
  5. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  6. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.
  7. Before replacing the certification ECU, refer to the engine immobiliser system (w/ Smart Key System) (Click here).

1.CHECK POWER DOOR LOCK CONTROL SYSTEM
  1. When the door control switch on the multiplex network master switch assembly is operated, check that the doors unlock and lock according to the switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.READ VALUE USING TECHSTREAM (ENTRY CANCEL FUNCTION)
  1. Using the Techstream, read the Data List (Click here).

    Smart Key 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Auto Entry Cancel SW
    Entry door lock function cancel / ON or OFF
    Mode status displayed
    -
    Result 
    Result
    Proceed to
    Entry door lock function cancel is OFF
    A
    Entry door lock function cancel is ON
    B



B
PERFORM CANCELLATION OF ENTRY CANCEL FUNCTION (Click here)
A


3.CHECK WAVE ENVIRONMENT
  1. Move the electrical key transmitter as described below and perform the operation inspection (Click here).

    HINT:
    1. When the electrical key transmitter is brought near the door outside handle or electrical key antenna, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. The transmitting wave of the wireless function and entry function are the same, but the wave logic is different. As a result, it is possible that only the wireless function or only the entry function is affected by wave interference.

    1. Bring the electrical key transmitter approximately 0.3 m (0.984 ft.) from the door outside handle (for driver side) and perform a driver door entry lock and unlock operation check.

      NOTICE:
      If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication may not possible.

    2. Bring the electrical key transmitter approximately 0.3 m (0.984 ft.) from the door outside handle (for front passenger side) and perform a front passenger door entry lock and unlock operation check.

      NOTICE:
      If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication may not possible.

    3. Bring the electrical key transmitter approximately 0.3 m (0.984 ft.) from the electrical key antenna (outside luggage) and perform an entry back door unlock function check.

      NOTICE:
      If the key is brought within 0.2 m (0.656 ft.) of the rear bumper, communication may not possible.

      HINT:
      If the inspection result is that the problem only occurs in certain locations or at certain times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      Result 
      Result
      Proceed to
      All operation checks fail
      A
      All checks are normal
      B
      Some operation checks are normal
      C



B
AFFECTED BY WAVE INTERFERENCE

C
GO TO OTHER PROBLEM (PROCEED TO PROBLEM SYMPTOMS TABLE FOR EACH DOOR) (Click here)
A


4.CHECK ELECTRICAL KEY ANTENNAS IN KEY DIAGNOSTIC MODE
  1. Check the following antennas in the key diagnostic mode (Click here).

    1. Check the electrical key antenna (for driver side).
      When the electrical key transmitter is brought within 0.7 to 1.0 m (2.30 to 3.28 ft.) of the door outside handle (for driver side), check that the wireless door lock buzzer sounds.

    2. Check the electrical key antenna (for front passenger side).
      When the electrical key transmitter is brought within 0.7 to 1.0 m (2.30 to 3.28 ft.) of the door outside handle (for front passenger side), check that the wireless door lock buzzer sounds.

    3. Check the indoor No. 1 electrical key antenna (front floor).
      When the electrical key transmitter is at the inspection point, check that the wireless door lock buzzer sounds.

    4. Check the indoor No. 2 electrical key antenna (rear floor).
      When the electrical key transmitter is at the inspection point, check that the wireless door lock buzzer sounds.

    5. Check the indoor No. 2 electrical key antenna (inside luggage).
      When the electrical key transmitter is at the inspection point, check that the wireless door lock buzzer sounds.

    6. Check the electrical key antenna (outside luggage).
      When the electrical key transmitter is brought within 0.7 to 1.0 m (2.30 to 3.28 ft.) of the electrical key antenna (outside luggage), check that the wireless door lock buzzer sounds.

      OK:
      Wireless door lock buzzer sounds.

      Result 
      Result
      Proceed to
      All diagnostic mode inspections fail
      A
      Some diagnostic mode inspections fail (door)
      B
      Some diagnostic mode inspections fail (interior)
      C
      Some diagnostic mode inspections fail (back door)
      D
      All diagnostic mode inspections are normal
      E



B
GO TO OTHER FLOWCHART (PROCEED TO PROBLEM SYMPTOM FLOWCHART FOR EACH DOOR) (Click here)

C
GO TO OTHER FLOWCHART (Click here)

D
GO TO OTHER FLOWCHART (Click here)

E
REPLACE CERTIFICATION ECU (Click here)
A


5.REPLACE ELECTRICAL KEY TRANSMITTER
  1. Replace the electrical key transmitter with a new one.

  1. Perform the registration procedure (Click here).


NEXT


6.CHECK OPERATION
  1. Check the operation of the entry lock function (Click here).

    OK:
    Entry lock function operates normally.



NG
REPLACE CERTIFICATION ECU (Click here)
OK

END (ELECTRICAL KEY TRANSMITTER IS DEFECTIVE)