DTC P0500 Vehicle Speed Sensor "A" |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0500 | While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic). |
|
| Related DTCs | P0500: Vehicle speed sensor "A" pulse input error |
| Required Sensors/Components (Main) | Vehicle speed sensor, Combination meter assembly and Skid control ECU |
| Required Sensors/Components (Related) | Park/neutral position switch, Engine coolant temperature sensor, Crankshaft position sensor, Throttle position sensor and Mass air flow meter |
| Frequency of Operation | Continuous |
| Duration | 5 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Time after ignition switch turned from off to ON | 3 seconds or more |
| Transfer neutral switch* | Not "N" position |
| Vehicle speed | 9 km/h (5.59 mph) or more |
| Battery voltage | 8 V or higher |
| Starter | OFF |
| Vehicle speed sensor signal | No pulse input |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK OPERATION OF SPEEDOMETER |
Drive the vehicle and check whether the operation of the speedometer in the combination meter assembly is normal.
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (VEHICLE SPD) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.
Drive the vehicle.
Read the value displayed on the Techstream.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (ECM - COMBINATION METER ASSEMBLY) |
Disconnect the ECM connector.
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F14-28 (+S) - F51-18 (SPD) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| F14-28 (+S) or F51-18 (SPD) - Body ground | Always | Below 1 Ω |
Reconnect the ECM connector.
Reconnect the combination meter assembly connector.
|
| ||||
| OK | |
| 4.CHECK COMBINATION METER ASSEMBLY (VOLTAGE) |
![]() |
Disconnect the combination meter assembly connector.
Turn the ignition switch to ON.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F14-28 (+S) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
Reconnect the combination meter assembly connector.
|
| ||||
| OK | |
| 5.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL OUTPUT WAVEFORM) |
![]() |
Remove the combination meter assembly (Click here).
Connect the combination meter assembly connector.
Move the shift lever to the neutral position.
Jack up the vehicle.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter assembly and the body ground while the wheel is turned slowly.
| Tester Connection | Switch Condition | Specified Condition |
| F14-28 (+S) - Body ground | Ignition switch ON (Turn wheel slowly) | Voltage generated intermittently |
| *a | Component with harness connected (Combination Meter Assembly) |
| *b | Turn Wheel |
Reinstall the combination meter assembly (Click here).
|
| ||||
| OK | ||
| ||
| 6.CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM) |
![]() |
Remove the combination meter assembly (Click here).
Connect the combination meter assembly connector.
Move the shift lever to the neutral position.
Jack up the vehicle.
Turn the ignition switch to ON.
Check the voltage between the terminal of the combination meter assembly and the body ground while the wheel is turned slowly.
| Tester Connection | Switch Condition | Specified Condition |
| F14-29 (SI) - Body ground | Ignition switch ON (Turn wheel slowly) | Voltage generated intermittently |
| *a | Component with harness connected (Combination Meter Assembly) |
| *b | Turn Wheel |
Reinstall the combination meter assembly (Click here).
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU) |
Disconnect the skid control ECU connector.
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F14-29 (SI) - A6-12 (SP1) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| F14-29 (SI) or A6-12 (SP1) - Body ground | Always | Below 1 Ω |
Reconnect the skid control ECU connector.
Reconnect the combination meter assembly connector.
|
| ||||
| OK | ||
| ||