Home › Drivetrain ยท A750F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TORQUE CONVERTER ASSEMBLY


    C272271
  1. Engage the splines of the input shaft and turbine runner.



    C272272
  1. Engage the splines of the stator shaft and stator while turning the torque converter assembly.

    HINT:
    If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm (0.394 in.) and engage the splines while rotating the torque converter assembly.



    C272273
  1. Turn the torque converter assembly to engage the key of the oil pump drive gear into the slot on the torque converter assembly.



    C209683E01
  1. Using a vernier caliper and straightedge, measure dimension A between the transmission contact surface of the engine and the torque converter contact surface of the drive plate.



    C209689E01
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the first step.

    Standard distance:
    B = A + 1 mm (0.0394 in.) or more

    NOTICE:
    1. Make sure to deduct the thickness of the straightedge.
    2. If the transmission is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.



2. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
  1. Install the No. 1 transmission control cable bracket to the automatic transmission assembly with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



3. INSTALL TRANSFER ASSEMBLY
  1. for VF4BM: (Click here)
  2. for VF2BM: (Click here
  3. for VF2A: (Click here)


4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


    C218126E01
  1. Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter centerpiece.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent
    Maximum grease amount:
    Approximately 1 g (0.0353 oz.)

    Text in Illustration 
    *1
    Torque Converter Centerpiece
    *2
    Crankshaft



    C217032E01
  1. Confirm that 2 knock pins are on the automatic transmission assembly contact surface of the engine cylinder block before automatic transmission assembly installation.

  1. Keeping the engine assembly and the automatic transmission assembly in a horizontal position, align the knock pins with each hole on the automatic transmission assembly and install the 9 bolts.

    Torque:
    for 17 mm head bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for 14 mm head bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

    NOTICE:
    1. Make sure not to pinch or damage any wire harness.
    2. Make sure the knock pin is fully engaged with the knock pin hole.
    3. Do not forcibly pry the automatic transmission assembly.
    4. After installing the automatic transmission assembly, confirm that the torque converter assembly can be rotated by hand.



5. CONNECT BREATHER HOSE
  1. Connect the 3 breather hoses to the engine assembly.



6. CONNECT WIRE HARNESS AND CONNECTOR


  1. for VF4BM:



    1. Connect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control side connector.

      HINT:
      Pull up the lever until the claw of the transmission wire connector makes a connection sound.



      C218115E02

    2. Attach the 2 connector clamps and 7 harness clamps.



  1. for VF2BM:



    1. Connect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors, transfer control side connector and 2 indicator switch connectors.

      HINT:
      Pull up the lever until the claw of the transmission wire connector makes a connection sound.



      C270512

    2. Attach the 2 connector clamps and 7 harness clamps.



  1. for VF2A:



    1. Connect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and 3 transfer connector.

      HINT:
      Pull up the lever until the claw of the transmission wire connector makes a connection sound.



      C217198E02

    2. Attach the 2 connector clamps and 5 harness clamps.

  1. Tilt up the automatic transmission.

  1. Connect the ground cable with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



7. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
  1. Install the rear No. 1 engine mounting insulator to the automatic transmission assembly with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

  1. Install the rear engine mounting heat insulator to the rear No. 1engine mounting insulator.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



8. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
  1. Install the No. 3 frame crossmember sub-assembly to the rear No. 1 engine mounting insulator with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Install the No. 3 frame crossmember sub-assembly to the frame with the 4 bolts and 4 nuts.

    NOTICE:
    Insert the bolt from the front of the vehicle.

    HINT:
    Hold the bolts and tighten the nuts.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }



9. INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH (for X-Runner)
  1. Install the front suspension member bracket LH and RH with the 8 bolts.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }



10. INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT
  1. Turn the crankshaft to gain access to the installation locations of the 6 drive plate and torque converter setting bolts and install each bolt while holding the crankshaft pulley setting bolt with a wrench.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Install the black bolt first, and then the 5 silver bolts.



11. INSTALL FLYWHEEL HOUSING SIDE COVER
  1. Install the flywheel housing side cover to the engine.



12. CONNECT NO. 1 INLET OIL COOLER TUBE AND NO. 1 OUTLET OIL COOLER TUBE
  1. Temporarily install the ends of the No. 1 inlet oil cooler tube and No. 1 outlet oil cooler tube to each oil cooler tube union by hand.

  1. Connect the 2 clamps and install the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Using a union nut wrench, tighten the No. 1 inlet oil cooler tube and No. 1 outlet oil cooler tubes.

    Torque:
    34 N*m{ 346 kgf*cm , 25 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



13. INSTALL STARTER ASSEMBLY
  1. (Click here)



14. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Connect the transmission control cable assembly to the No. 1 transmission control cable bracket with a new clip, and connect the cable end to the control shaft lever with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



15. INSTALL MANIFOLD STAY
  1. Install the manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



16. INSTALL NO. 2 MANIFOLD STAY
  1. Install the No. 2 manifold stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



17. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(Click here)


18. INSTALL PROPELLER SHAFT ASSEMBLY
(Click here)


19. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


20. INSTALL TRANSFER CASE LOWER PROTECTOR
  1. Install the transfer case lower protector with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



21. INSTALL TRANSFER HIGH AND LOW SHIFT LEVER ASSEMBLY (for VF2A)


    C213733E01
  1. While pushing the select return spring to the left with the end of the transfer high and low shift lever assembly, insert the end of the transfer high and low shift lever assembly into the shift fork.
    Text in Illustration 
    *1
    Select Return Spring



    C213734E02
  1. While holding down the shift lever cap, install the snap ring to install the transfer high and low shift lever assembly.
    Text in Illustration 
    *1
    Shift Lever Cap

  1. Return the transfer front drive shift boot to its original position.



22. INSTALL NO.1 SHIFT AND SELECT LEVER BOOT (for VF2A)
  1. Install the No. 1 shift and select lever boot with the 4 screws.



23. INSTALL CONSOLE BOX ASSEMBLY (for VF2A)
(Click here)


24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



25. ADD AUTOMATIC TRANSMISSION FLUID
(Click here)


26. ADJUST SHIFT LEVER POSITION
  1. Remove the rear console box (Click here).

  1. Move the shift lever to N.



    C203381E01
  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.
    Text in Illustration 
    *1
    Slider
    *2
    Lock Piece



    C204598E04
  1. Push the lock piece into the adjuster case and lock it.

    NOTICE:
    Make sure that the lock piece is completely locked by the slider.

  1. Install the rear console box (Click here).



27. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch to on (IG) and the brake pedal depressed, make sure that it moves smoothly and correctly into position.

  1. Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves in reverse after moving the shift lever to R.
    If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the transmission floor shift assembly installation condition.



28. INSPECT FOR EXHAUST GAS LEAK
  1. If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


29. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the front fender apron seal RH with the 4 clips.



30. INSTALL NO. 1 FRONT FENDER APRON TO FRAME SEAL RH
  1. Install the front No. 1 fender apron to frame seal RH with the 5 clips.



31. INSTALL REAR ENGINE UNDER COVER ASSEMBLY
  1. Install the rear engine under cover assembly with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



32. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY


    A224743
  1. Hook the No. 1 engine under cover sub-assembly to the vehicle body as shown in the illustration.

  1. Install the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



33. PERFORM RESET MEMORY
(Click here)