Home › Drivetrain ยท A750E AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


C209683E01
  1. Using a vernier caliper and straightedge, measure dimension "A" between the transmission fitting surface of the engine*1 and the torque converter clutch fitting surface of the drive plate*2 (step 1).



    C209685E04
  1. Align the matchmarks on the transmission case and torque converter clutch, and then mesh the splines of the input shaft and turbine runner.
    Text in Illustration 
    *1
    Matchmark



    C209687E03
  1. Mesh the splines of the stator shaft and stator while turning the torque converter clutch.
    Text in Illustration 
    *1
    Matchmark

    HINT:
    Turn the torque converter clutch approximately 180°.



    C217017E01
  1. Turn the torque converter clutch and align the matchmarks on the torque converter clutch and transmission case to fit the key of the oil pump drive gear into the slot on the torque converter clutch.
    Text in Illustration 
    *1
    Matchmark

    NOTICE:
    Do not push on the torque converter clutch when aligning the matchmarks.



    C209689E01
  1. Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that B is more than A (measured in step 1).

    Standard distance:
    A + 1 mm (0.0394 in.) or more



2. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET
  1. Install the transmission control cable bracket with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



3. INSTALL WIRE HARNESS CLAMP BRACKET
  1. Install the 4 brackets with the 4 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


C218126E01
  1. Apply clutch spline grease to the surface of the crankshaft that contacts the torque converter clutch centerpiece.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent
    Maximum grease amount:
    Approximately 1 g (0.0353 oz.)

    Text in Illustration 
    *1
    Torque Converter Clutch Center Peace
    *2
    Crankshaft



    C209695E01
  1. Confirm that the 2 knock pins are on the transmission contact surface of the engine block before transmission installation.

  1. Install the automatic transmission with the 9 bolts.

    Torque:
    for 17 mm head bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for 14 mm head bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



5. CONNECT BREATHER PLUG HOSE
  1. Connect the breather plug hose to the engine.



6. CONNECT WIRE HARNESS AND CONNECTOR


  1. Connect the park/neutral start switch connector, transmission wire connector and 2 speed sensor connectors.

    HINT:
    Push up the lever until the claw of the transmission wire connector makes a connection sound.



    C216983E02

  1. Connect the 2 connector clamps and 4 harness clamps.

  1. Tilt up the automatic transmission.



7. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

  1. Install the rear engine mounting heat insulator to the engine mounting insulator.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



8. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
  1. Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Install the frame crossmember with the 4 bolts and 4 nuts.

    Torque:
    72 N*m{ 734 kgf*cm , 53 ft.*lbf }



9. INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH (for X-Runner)
  1. Install the front suspension member bracket LH and RH with the 8 bolts.

    Torque:
    33 N*m{ 337 kgf*cm , 24 ft.*lbf }



10. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT


    C218128
  1. Turn the crankshaft to gain access to the installation locations of the 6 torque converter clutch setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

    NOTICE:
    Install the black bolt first, and then the 5 silver bolts.

  1. Install the flywheel housing side cover.



11. INSTALL STARTER ASSEMBLY
  1. Install the starter (Click here).



12. CONNECT NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE
  1. Temporarily install the ends of the oil cooler inlet tube and outlet tub to each oil cooler tube union by hand.

  1. Close the 2 No. 2 flexible hose clamps and install the 2 bolts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Using a union nut wrench, tighten the inlet and outlet tubes.

    Torque:
    34 N*m{ 347 kgf*cm , 25 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



13. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
  1. Connect the transmission control cable to the transmission control cable bracket with a new clip, and connect the cable end to the control shaft lever with the nut.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }



14. INSTALL NO. 2 MANIFOLD STAY
  1. Install the stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



15. INSTALL MANIFOLD STAY
  1. Install the stay with the 3 bolts.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }



16. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install the front exhaust pipe (Click here).



17. INSTALL PROPELLER SHAFT ASSEMBLY
  1. Install the propeller shaft (Click here).



18. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).



19. ADD AUTOMATIC TRANSMISSION FLUID
  1. Add automatic transmission fluid (Click here).



20. ADJUST SHIFT LEVER POSITION
  1. Remove the rear console box (Click here).

  1. Move the shift lever to N.



    C203381E01
  1. Slide the slider in the direction shown in the illustration and pull out the lock piece.
    Text in Illustration 
    *1
    Slider
    *2
    Lock Piece



    C204598E04
  1. Push the lock piece into the adjuster case and lock it.

    NOTICE:
    Make sure that the lock piece is completely locked by the slider.

  1. Install the rear console box (Click here).



21. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from P to R with the ignition switch to on (IG) and the brake pedal depressed, make sure that it moves smoothly and correctly into position.

  1. Check that the shift lever does not stop when moving the shift lever from R to P, and check that the shift lever does not stick when moving the shift lever from D to S.

  1. Start the engine and make sure that the vehicle moves forward after moving the shift lever from N to D and moves in reverse after moving the shift lever to R.
    If the operation cannot be performed as specified, inspect the park/neutral position switch assembly and check the transmission floor shift assembly installation condition.



22. INSPECT FOR EXHAUST GAS LEAK
  1. If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


23. INSTALL FRONT NO. 1 FENDER APRON TO FRAME SEAL RH
  1. Install the front No. 1 fender apron to frame seal RH with the 5 clips.



24. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the front fender apron seal RH with the 4 clips.



25. INSTALL REAR ENGINE UNDER COVER ASSEMBLY
  1. Install the rear engine under cover assembly with the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



26. INSTALL NO. 1 ENGINE UNDER COVER


    A224743
  1. Hook the No. 1 engine under cover sub-assembly to the vehicle body as shown in the illustration.

  1. Install the 4 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }



27. PERFORM RESET MEMORY
  1. Perform the RESET MEMORY procedures (A/T initialization) (Click here).