Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0016    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)

DTC    P0017    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)

DTC    P0018    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)

DTC    P0019    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)

for Preparation Click here


DESCRIPTION

The VVT (Variable Valve Timing) system is composed of an ECM, camshaft timing oil control valve assembly, camshaft timing gear assembly (for intake side), and camshaft timing gear assembly (for exhaust side). This VVT system controls the operation of camshaft timing gear assembly (for intake and exhaust sides) to obtain optimum valve timing according to the driving conditions based on various sensor signals such as intake air volume, throttle position, and engine coolant temperature. The ECM controls the camshaft timing oil control valve assembly based on these signals, obtaining the optimum relative positions of the camshafts, in turn improving fuel economy, emission efficiency, and achieving higher output. In addition, the ECM detects the actual valve timing based on the signal from the camshaft position sensor and performs feedback control to obtain ideal valve timing.

DTC No.
DTC Detection Condition
Trouble Area
P0016
Intake camshaft position has slipped from the threshold for 1 second (bank 1).
(2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for intake side of bank 1)
  3. Oil control valve filter (bank 1)
  4. Camshaft timing gear assembly (for intake side of bank 1)
  5. ECM
P0017
Exhaust camshaft position has slipped from the threshold for 5 seconds (bank 1).
(2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for exhaust of bank 1)
  3. Oil control valve filter (bank 1)
  4. Camshaft timing gear assembly (for exhaust side of bank 1)
  5. ECM
P0018
Intake camshaft position has slipped from the threshold for 1 second (bank 2).
(2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for intake side of bank 2)
  3. Oil control valve filter (bank 2)
  4. Camshaft timing gear assembly (for intake side of bank 2)
  5. ECM
P0019
Exhaust camshaft position has slipped from the threshold for 5 seconds (bank 2).
(2 trip detection logic)
  1. Valve timing
  2. Camshaft timing oil control valve assembly (for exhaust side of bank 2)
  3. Oil control valve filter (bank 2)
  4. Camshaft timing gear assembly (for exhaust side of bank 2)
  5. ECM

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT neutral position against the VVT learning value while coasting. If the VVT neutral position is out of the specified VVT learning value range in driving cycles, the ECM illuminates the MIL and stores DTC P0016 (bank 1) or P0018 (bank 2).
To monitor the correlation of the exhaust camshaft position and crankshaft position, the ECM checks the VVT neutral position against VVT learning value while idling. If the VVT neutral position is out of the specified VVT learning value range in driving cycles, the ECM illuminates the MIL and stores DTC P0017 (bank 1) or P0019 (bank 2).

CONFIRMATION DRIVING PATTERN



  1. A315263E01

  2. Connect the GTS to the DLC3.
  3. Turn the ignition switch to ON and turn the GTS on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the GTS on.
  7. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
  8. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].
  9. When the engine speed exceeds 50 km/h {31.1 MPH}, release the accelerator pedal, brake pedal, and clutch pedal to decelerate without shifting down. Make sure to select the optimum gear in advance so that the engine speed is maintained between 2500 rpm and 1200 rpm for more than 3 seconds [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  10. Stop the vehicle.
  11. Idle the engine for 5 minutes or more [C].
  12. Enter the following menus: Powertrain / Engine / Trouble Codes.
  13. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  14. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  15. Input the DTC: P0016, P0017, P0018 or P0019.
  16. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  17. If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0010 for the camshaft timing oil control valve assembly (for intake camshaft) circuit .
Refer to DTC P0013 for the camshaft timing oil control valve assembly (for exhaust camshaft) circuit .

INSPECTION PROCEDURE

HINT:
  1. If DTC P0016 or P0017 is displayed, check the intake camshaft circuit for the right bank VVT system (bank 1).
  2. If DTC P0018 or P0019 is displayed, check the intake camshaft circuit for the left bank VVT system (bank 2).
  3. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from transmission.
  4. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  5. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016, P0017, P0018 OR P0019)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    DTC P0016, P0017, P0018 or P0019 is output
    A
    DTC P0016, P0017, P0018 or P0019 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0016, P0017, P0018 or P0019 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING GTS (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY)

HINT:
If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.

  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the A/C on.

  1. Turn the GTS on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 1) / VVT Change Angle #1, VVT Ex Chg Angle #1, VVT Change Angle #2, VVT Ex Chg Angle #2.

  1. Perform the Active Test. Check that the displacement angle varies.

    OK:
    Displacement angle varies.



NG
Go to step 4
OK


3.CHECK VALVE TIMING
  1. Check the valve timing (Click here).


Result 
Result
Proceed to
NG
A
OK
B


B
Go to step 8
A

ADJUST VALVE TIMING (Click here)  

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)
  1. Inspect the camshaft timing oil control valve assembly (for intake or exhaust camshaft) (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT) (Click here)
OK


5.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE
  1. Check that the oil control valve filter and oil pipe are not clogged.

OK:
The oil control valve filter and oil pipe are not clogged.



NG
CLEAN OR REPLACE OIL CONTROL VALVE FILTER AND OIL PIPE
OK


6.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY (FOR INTAKE OR EXHAUST CAMSHAFT)
  1. Inspect the camshaft timing gear assembly (for intake camshaft or exhaust camshaft) .



NG
REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (INTAKE OR EXHAUST CAMSHAFT) (Click here)
OK


7.CLEAN LUBRICATION SYSTEM
  1. Replace the engine oil (Click here).

  1. Warm up the engine for 5 minutes, and then stop the engine.

  1. Replace the engine oil and filter (Click here).


NEXT


8.CLEAR DTC
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.


NEXT


9.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016, P0017, P0018 OR P0019)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Start the engine and warm it up.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.

  1. Read pending DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC P0016, P0017, P0018 or P0019 is output
    B



B
REPLACE ECM (Click here)
A

END