DTC P0037 Oxygen Sensor Heater Control Circuit Low (Bank 1 Sensor 2) |
DTC P0038 Oxygen Sensor Heater Control Circuit High (Bank 1 Sensor 2) |
DTC P0141 Oxygen Sensor Heater Circuit (Bank 1 Sensor 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0037 | Heated oxygen sensor heater voltage is less than battery voltage X 0.3 V for 10 seconds or more. (2 trip detection logic) |
|
| P0038 | Heated oxygen sensor heater voltage is battery voltage X 0.2 V or more for 10 seconds or more. (2 trip detection logic) | |
| P0141 | Heated oxygen sensor heater voltage is less than battery voltage X 0.88 V for 10 seconds or more. (2 trip detection logic) |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE) |
Inspect the heated oxygen sensor (Click here).
|
| ||||
| OK | |
| 2.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF HEATED OXYGEN SENSOR) |
![]() |
Disconnect the heated oxygen sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C13-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Heated Oxygen Sensor) |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - ECM) |
Disconnect the heated oxygen sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-6 (HT1B) - C13-1 (HT1B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-6 (HT1B) or C13-1 (HT1B)- Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0037, P0038 OR P0141) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0037, P0038 or P0141 is output | B |
|
| ||||
| A | ||
| ||
| 5.INSPECT RELAY (EFI MAIN2) |
Check the EFI MAIN2 relay .
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR - EFI MAIN2 RELAY) |
Disconnect the heated oxygen sensor connector.
Remove the EFI MAIN2 relay from the engine room relay block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI MAIN2 relay terminal 3 - C13-2 (+B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| EFI MAIN2 relay terminal 3 or C13-2 (+B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||