DTC P0365 Camshaft Position Sensor "B" Circuit (Bank 1) |
DTC P0366 Camshaft Position Sensor "B" Circuit Range / Performance (Bank 1) |
DTC P0390 Camshaft Position Sensor "B" Circuit (Bank 2) |
DTC P0391 Camshaft Position Sensor "B" Circuit Range / Performance (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0365 | No VVT sensor for exhaust side signal input during crankshaft 7.5 rotations (bank 1). (1 trip detection logic) |
|
| P0366 | 2 VVT sensor for exhaust side signals are not output during crankshaft 2 rotations (bank 1). (1 trip detection logic) | |
| P0390 | No VVT sensor for exhaust side signal input during crankshaft 7.5 rotations (bank 2). (1 trip detection logic) |
|
| P0391 | 2 VVT sensor for exhaust side signals are not output during crankshaft 2 rotations (bank 2). (1 trip detection logic) |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK VVT SENSOR FOR EXHAUST SIDE (SENSOR POWER SOURCE) |
![]() |
Disconnect the VVT sensor for exhaust side connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C6-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| C25-1 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | Bank 1 |
| *B | Bank 2 |
| *a | Front view of wire harness connector (to VVT Sensor for Exhaust Side) |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - ECM) |
Disconnect the ECM connector.
Disconnect the VVT sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A34-14 (EV1+) - C6-2 (EV1+) | Always | Below 1 Ω |
| A34-25 (EV2+) - C25-2 (EV2+) | Always | Below 1 Ω |
| A34-34 (VVE) - C6-3 (EV1-) | Always | Below 1 Ω |
| A34-34 (VVE) - C25-3 (EV2-) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A34-14 (EV1+) or C6-2 (EV1+) - Body ground | Always | 10 kΩ or higher |
| A34-25 (EV2+) or C25-2 (EV2+) - Body ground | Always | 10 kΩ or higher |
| A34-34 (VVE) or C6-3 (EV1-) - Body ground | Always | 10 kΩ or higher |
| A34-34 (VVE) or C25-3 (EV2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST SIDE) |
![]() |
Check the VVT sensor installation.
|
| ||||
| OK | |
| 4.CHECK CAMSHAFT TIMING GEAR ASSEMBLY (TEETH OF PLATE) |
Check the teeth of the sensor plate.
|
| ||||
| OK | |
| 5.CHECK VALVE TIMING |
Check the valve timing (Click here).
|
| ||||
| OK | |
| 6.REPLACE VVT SENSOR FOR EXHAUST SIDE |
Replace the VVT sensor for exhaust side (Click here).
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0365, P0366, P0390 OR P0391) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine.
Turn the GTS on.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read the DTC.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0365, P0366, P0390 or P0391 is output | B |
|
| ||||
| A | ||
| ||
| 8.INSPECT RELAY (EFI MAIN1) |
Inspect the EFI MAIN1 relay .
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR EXHAUST SIDE - EFI MAIN1 RELAY) |
Disconnect the VVT sensor for exhaust side connector.
Remove the EFI MAIN1 relay from the engine room relay block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| EFI MAIN1 relay terminal 3 - C6-1 (+B) | Always | Below 1 Ω |
| EFI MAIN1 relay terminal 3 - C25-1 (+B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| EFI MAIN1 relay terminal 3 or C6-1 (+B) - Body ground | Always | 10 kΩ or higher |
| EFI MAIN1 relay terminal 3 or C25-1 (+B) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||