Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > VSC OFF Indicator Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
Pressing the VSC OFF switch turns off TRC and pressing and holding this switch turns off TRC and VSC. If VSC is turned off, the VSC OFF indicator light will come on.

WIRING DIAGRAM


C264068E01


INSPECTION PROCEDURE

NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (Click here).

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)
OK


4.READ VALUE USING GTS (VSC OFF SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the GTS (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    TRC(TRAC)/VSC Off Mode
    TRC/VSC OFF mode / Normal, TRC(TRAC) OFF or VSC OFF
    Normal: Normal mode
    TRC(TRAC) OFF: TRC OFF mode
    VSC OFF: VSC OFF mode
    -

  1. Using the GTS, check that the switch condition displayed on the GTS changes according to VSC OFF switch operation.

    OK:
    The GTS display changes according to VSC OFF switch operation.



NG
Go to step 7
OK


5.READ VALUE USING GTS (VSC SPORT SWITCH)
  1. Select the Data List using the GTS (Click here).

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Sports Mode
    VSC SPORT mode / Normal or Sports
    Normal: Normal mode
    Sports: VSC SPORT mode
    -

  1. Using the GTS, check that the switch condition displayed on the GTS changes according to VSC SPORT switch operation.

    OK:
    The GTS display changes according to VSC SPORT switch operation.



NG
Go to step 9
OK


6.INSPECT COMBINATION METER ASSEMBLY
  1. Perform an Active Test of the combination meter assembly (meter CPU) using the GTS (Click here).

  1. Check the combination meter assembly.

    OK:
    The VSC OFF indicator and VSC SPORT indicator lights turn on or off in accordance with the Active Test operation.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

7.INSPECT VSC OFF SWITCH
  1. Remove the VSC OFF switch (Click here).

  1. Inspect the VSC OFF switch (Click here).



NG
REPLACE PATTERN SELECT SWITCH ASSEMBLY (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC OFF SWITCH)
  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A5-12 (CSW1) - D35-5
    Always
    Below 1 Ω
    A5-12 (CSW1) - Body ground
    Always
    10 kΩ or higher
    D35-8 - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)  

9.INSPECT VSC SPORT SWITCH
  1. Remove the VSC SPORT switch (Click here).

  1. Inspect the VSC SPORT switch (Click here).



NG
REPLACE PATTERN SELECT SWITCH ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - VSC SPORT SWITCH)
  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A5-27(CSW2) - D35-1
    Always
    Below 1 Ω
    A5-27(CSW2) - Body ground
    Always
    10 kΩ or higher
    D35-8 - Body ground
    Always
    Below 1 Ω

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)