Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1492    Clutch Switch OFF Stuck

DTC    C1493    Clutch Switch ON Stuck

for Preparation Click here


DESCRIPTION

The clutch switch signal is sent to the skid control ECU (brake actuator assembly) via the CAN communication system.
If any faults are present in the CAN communication cable with the ECM, DTC U0100 (Lost Communication with ECM / PCM "A") is stored.

DTC No.
DTC Detection Condition
Trouble Area
C1492
Clutch switch system circuit has a malfunction
  1. CAN communication system
  2. Clutch switch assembly
  3. Skid control ECU (Brake actuator assembly)
  4. ECM
  5. Wire harness or connector
C1493
Clutch switch system circuit has a malfunction
  1. CAN communication system
  2. Clutch switch assembly
  3. Skid control ECU (Brake actuator assembly)
  4. ECM
  5. Wire harness or connector

WIRING DIAGRAM


C361085E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).


Result:

Result
Proceed to
DTC is not output.
A
DTC is output.
B



B
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) (Click here)
A


2.READ VALUE USING GTS (CLUTCH SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List using the GTS.

    Powertrain / Engine / Data List 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Clutch Switch
    Clutch switch status/ ON or OFF
    ON: Clutch pedal depressed
    OFF: Clutch pedal released
    -

    OK:
    The GTS displays ON or OFF according to the brake pedal operation.



NG
Go to step 4
OK


3.RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Start the engine.

  1. Drive the vehicle at a speed of 45 km/h (28 mph) or more for at least 120 seconds.

  1. Check if the same DTC is output (Click here).


Result:

Result
Proceed to
DTCs C1492 and/or C1493 are not output.
A
DTCs C1492 and/or C1493 are output.
B



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)  

4.INSPECT CLUTCH SWITCH ASSEMBLY
  1. Inspect the clutch switch assembly.

for LHD:
for RHD:

Result:

Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C



B
REPLACE CLUTCH SWITCH ASSEMBLY (Click here)

C
REPLACE CLUTCH SWITCH ASSEMBLY (Click here)
A


5.CHECK HARNESS AND CONNECTOR (CLUTCH SWITCH ASSEMBLY POWER SOURCE TERMINAL)
  1. Disconnect the clutch switch assembly connector.



    C365248E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A21-1 - Body ground
    Ignition Switch ON
    11 to 14 V
    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Clutch Switch Assembly)



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH SWITCH ASSEMBLY)
  1. Disconnect the clutch switch connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):
    Tester Connection
    Condition
    Specified Condition
    A33-15 (CLSW) - A21-2
    Always
    Below 1 Ω

    Standard Resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    A33-15 (CLSW) or A21-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR
OK

REPLACE ECM (Click here)