Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › 2012.03–2016.06
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0335  Crankshaft Position Sensor "A" Circuit  P0336  Crankshaft Position Sensor Range / Performance  


DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and Magnetoresistive Element (MRE) type sensor. The crankshaft angle sensor plate is installed on the crankshaft. The crankshaft position sensor generates 30 signals per crankshaft revolution. The ECM uses the camshaft position signal to distinguish between the cylinders, and uses the crankshaft position signal to detect the crankshaft position and engine speed.

DTC No. DTC Detection Condition Trouble Area
P0335 No crankshaft position sensor signal is sent to the ECM while cranking for 3 seconds or more.
(1 trip detection logic)
·

Open or short in crankshaft position sensor circuit

·

Crankshaft position sensor

·

Crankshaft angle sensor plate (crankshaft sub-assembly)

·

ECM


P0336 Crankshaft position sensor signal is not 30 counts per 1 revolution of crankshaft.
(2 trip detection logic)
·

Crankshaft position sensor

·

Crankshaft angle sensor plate (crankshaft sub-assembly)

·

ECM



MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor and the ECM illuminates the MIL and sets a DTC.

CONFIRMATION DRIVING PATTERN

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine.

HINT:

If the engine could not be started, crank engine for 10 seconds.


7.

Idle the engine for 20 seconds or more.

8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0335 or P0336.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280068E03
4.26,1.917 4.5,2.125 0.24,0.208 10 false * 0.594,3.073 1.917,3.469 1.323,0.396 10 false *: Shielded 3.469,1.927 3.708,2.135 0.24,0.208 10 false * 5.375,1.698 5.688,2.063 0.313,0.365 10 false NE- 5.021,1.583 5.385,1.813 0.365,0.229 10 false A34 5.042,1.385 5.292,1.698 0.25,0.313 10 false 27 5.365,0.885 5.74,1.229 0.375,0.344 10 false NE+ 5.01,1.01 5.375,1.24 0.365,0.229 10 false A34 5.042,0.823 5.292,1.135 0.25,0.313 10 false 16 5.375,0.333 5.865,0.635 0.49,0.302 10 false SLE3 5.01,0.427 5.417,0.688 0.406,0.26 10 false A34 5.052,0.24 5.49,0.604 0.438,0.365 10 false 35 0.573,2.208 2.396,2.573 1.823,0.365 10 false Crankshaft Position Sensor 5.594,2.906 6.26,3.146 0.667,0.24 10 false ECM 0.583,2.031 1.073,2.333 0.49,0.302 10 false C33 1.865,0.885 2.208,1.063 0.344,0.177 10 false 1 1.865,1.458 2.198,1.667 0.333,0.208 10 false 2 1.49,0.875 1.865,1.177 0.375,0.302 10 false NE+ 1.5,1.469 1.906,1.813 0.406,0.344 10 false NE-

CAUTION / NOTICE / HINT

HINT:
·

If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.

·

The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:

(a)

Connect the GTS to the DLC3.

(b)

Start the engine.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.


The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.


·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.


e.

Start the engine.


f.

Read the values displayed on the GTS while the engine is running.

OK:

Correct values are displayed.


Result
Result Proceed to
NG A
OK B

HINT:
·

To check the engine speed change, display the graph on the GTS.

·

If the engine does not start, check the engine speed while cranking.

·

If the engine speed indicated on the GTS remains zero (0), there may be an open or short in the Crankshaft Position sensor circuit.





A

2.INSPECT CRANKSHAFT POSITION SENSOR

B

2.INSPECT CRANKSHAFT POSITION SENSOR
a.


OK

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the crankshaft position sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A34-16 (NE+) - C33-1 (NE+) Always Below 1 Ω
A34-27 (NE-) - C33-2 (NE-) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A34-16 (NE+) or C33-1 (NE+) - Body ground Always 10 kΩ or higher
A34-27 (NE-) or C33-2 (NE-) - Body ground Always 10 kΩ or higher




OK

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
A366136E06
0.479,1.813 0.719,2 0.24,0.188 10 false OK 2.677,1.833 2.917,2.021 0.24,0.188 10 false NG 1.646,1.552 2.448,1.75 0.802,0.198 10 false Clearance

a.

Check the crankshaft position sensor installation.

OK:

Sensor is installed correctly.




OK

5.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)

NG

5.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)
a.

Check the teeth of the No. 1 crankshaft position sensor plate.

OK:

Sensor plate does not have any cracks or deformation.




OK

6.REPLACE CRANKSHAFT POSITION SENSOR

NG

REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

6.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL).



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 OR P0336)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 OR P0336)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON and turn the tester on.


g.

Start the engine.


h.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Read DTCs.

Result
Result Proceed to
No DTC is output A
P0335 or P0336 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B