Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0201  Injector Circuit / Open - (Cylinder 1)  P0202  Injector Circuit / Open - (Cylinder 2)  P0203  Injector Circuit / Open - (Cylinder 3)  P0204  Injector Circuit / Open - (Cylinder 4)  


DESCRIPTION

The D-4S system has two injection systems. One is the in-cylinder direct injection system that directly injects pressurized fuel into the combustion chamber. The other is the intake port injection system. The ECM determines the percentage of in-cylinder direct injection to the intake port injection systems in accordance with the engine speed and load.

DTC No. DTC Detection Condition Trouble Area
P0201 Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel injector IC continuously 10 times or more (No. 1 cylinder).
(1 trip detection logic)
·

Open or short in fuel injector (for port injection) circuit (No. 1 cylinder)

·

INJ fuse

·

Fuel injector assembly (for port injection) (No. 1 cylinder)

·

ECM


P0202 Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel injector IC continuously 10 times or more (No. 2 cylinder).
(1 trip detection logic)
·

Open or short in fuel injector (for port injection) circuit (No. 2 cylinder)

·

INJ fuse

·

Fuel injector assembly (for port injection) (No. 2 cylinder)

·

ECM


P0203 Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel injector IC continuously 10 times or more (No. 3 cylinder).
(1 trip detection logic)
·

Open or short in fuel injector (for port injection) circuit (No. 3 cylinder)

·

INJ fuse

·

Fuel injector assembly (for port injection) (No. 3 cylinder)

·

ECM


P0204 Received diagnostic information (open circuit detected / GND short / +B short or overheating) from the fuel injector IC continuously 10 times or more (No. 4 cylinder).
(1 trip detection logic)
·

Open or short in fuel injector (for port injection) circuit (No. 4 cylinder)

·

INJ fuse

·

Fuel injector assembly (for port injection) (No. 4 cylinder)

·

ECM



MONITOR DESCRIPTION

The ECM monitors the injection control of the port injector. If a malfunction is detected in the port injector circuit, the ECM cancels the injection control for the corresponding cylinder and turns on the MIL.

CONFIRMATION DRIVING PATTERN

1.
A283032E17
0.188,0.458 1.146,0.76 0.958,0.302 10 false Engine Speed 0.167,2.521 1.125,2.74 0.958,0.219 10 false Vehicle Speed 0.896,1.75 1.271,2 0.375,0.25 10 false Idling 0.156,1 1.281,1.208 1.125,0.208 10 false 2500 to 3000 rpm 3.198,0.896 3.615,1.25 0.417,0.354 10 false [A] 5.396,2.677 5.771,2.896 0.375,0.219 10 false [B] 0.052,2.885 1.313,3.073 1.26,0.188 10 false 10 km/h (6.25 mph) 0.323,3.469 1.313,3.635 0.99,0.167 10 false 0 km/h (0 mph) 2.656,4.188 4.042,4.365 1.385,0.177 10 false 40 seconds or more 4.969,4.177 6.021,4.385 1.052,0.208 10 false 1 minute or more 6.552,3.99 7.021,4.417 0.469,0.427 10 false Time

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P0201, P0202, P0203 or P0204.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280104E06
4.177,1.021 4.479,1.24 0.302,0.219 10 false 2 2.99,1.01 3.344,1.24 0.354,0.229 10 false 1 2.823,1.385 4.604,1.771 1.781,0.385 10 false No. 1 Fuel Injector Assembly (for Port Injection) 5.208,1.031 5.583,1.219 0.375,0.188 10 false #10 5.208,0.354 5.708,0.656 0.5,0.302 10 false SSHUT 5.615,5.427 6.021,5.656 0.406,0.229 10 false ECM 2.542,1.385 2.906,1.552 0.365,0.167 10 false C8 4.844,1.135 5.208,1.333 0.365,0.198 10 false A36 4.844,0.448 5.198,0.625 0.354,0.177 10 false A35 4.875,0.948 5.188,1.177 0.313,0.229 10 false 12 4.875,0.26 5.208,0.427 0.333,0.167 10 false 13 1.229,5.219 1.906,5.521 0.677,0.302 10 false EFI(CTRL) 1.365,4.469 2.146,4.771 0.781,0.302 10 false EFI MAIN1 1.385,6.104 2.167,6.406 0.781,0.302 10 false Battery 1.167,4.135 1.417,4.344 0.25,0.208 10 false 3 1.167,4.823 1.396,5.031 0.229,0.208 10 false 5 0.656,4.823 0.906,5.01 0.25,0.188 10 false 2 0.656,4.135 0.927,4.333 0.271,0.198 10 false 1 2.865,2.375 4.656,2.76 1.792,0.385 10 false No. 2 Fuel Injector Assembly (for Port Injection) 2.542,2.375 2.917,2.552 0.375,0.177 10 false C30 2.875,3.302 4.688,3.656 1.813,0.354 10 false No. 3 Fuel Injector Assembly (for Port Injection) 2.552,3.313 2.792,3.49 0.24,0.177 10 false C9 2.865,4.25 4.625,4.625 1.76,0.375 10 false No. 4 Fuel Injector Assembly (for Port Injection) 2.51,4.25 2.833,4.427 0.323,0.177 10 false C31 5.208,1.948 5.531,2.198 0.323,0.25 10 false #20 4.844,2.063 5.198,2.24 0.354,0.177 10 false A36 4.875,1.875 5.198,2.042 0.323,0.167 10 false 22 5.208,2.885 5.594,3.094 0.385,0.208 10 false #30 4.833,2.99 5.167,3.156 0.333,0.167 10 false A36 4.875,2.792 5.146,2.99 0.271,0.198 10 false 32 5.208,3.802 5.594,4.021 0.385,0.219 10 false #40 4.844,3.917 5.156,4.083 0.313,0.167 10 false A36 4.875,3.729 5.146,3.927 0.271,0.198 10 false 13 4.198,1.938 4.469,2.167 0.271,0.229 10 false 2 2.979,1.938 3.292,2.135 0.313,0.198 10 false 1 4.198,2.854 4.5,3.094 0.302,0.24 10 false 2 2.99,2.854 3.292,3.094 0.302,0.24 10 false 1 4.188,3.802 4.438,4.115 0.25,0.313 10 false 2 2.969,3.802 3.219,4.031 0.25,0.229 10 false 1 1.25,5.594 1.76,5.896 0.51,0.302 10 false MAIN

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0201 is output, check the No. 1 fuel injector assembly (for port injection) (No. 1 cylinder) circuit.

·

If DTC P0202 is output, check the No. 2 fuel injector assembly (for port injection) (No. 2 cylinder) circuit.

·

If DTC P0203 is output, check the No. 3 fuel injector assembly (for port injection) (No. 3 cylinder) circuit.

·

If DTC P0204 is output, check the No. 4 fuel injector assembly (for port injection) (No. 4 cylinder) circuit.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
P0201, P0202, P0203 and P0204 are output A
P0201, P0202, P0203 or P0204 is output B
P0201, P0202, P0203 or P0204 and other DTCs are output C




A

2.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE VOLTAGE)

B

5.INSPECT RELAY (EFI MAIN1)

C

2.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE VOLTAGE)
a.
U146763E04
0.521,0.458 0.813,0.646 0.292,0.188 10 false C8 0.094,0.063 0.458,0.26 0.365,0.198 10 false *a 0.917,0.448 1.198,0.646 0.281,0.198 10 false *b 0.479,0.854 0.771,1.042 0.292,0.188 10 false C30 0.917,0.844 1.208,1.042 0.292,0.198 10 false *c 0.521,1.208 0.813,1.396 0.292,0.188 10 false C9 0.917,1.198 1.198,1.396 0.281,0.198 10 false *d 0.49,1.615 0.781,1.802 0.292,0.188 10 false C31 0.917,1.604 1.208,1.802 0.292,0.198 10 false *e

Disconnect the fuel injector assembly (for port injection) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C8-1 - Body ground Ignition switch ON 11 to 14 V
C30-1 - Body ground Ignition switch ON 11 to 14 V
C9-1 - Body ground Ignition switch ON 11 to 14 V
C31-1 - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Fuel Injector Assembly)
*b No. 1 cylinder
*c No. 2 cylinder
*d No. 3 cylinder
*e No. 4 cylinder



OK

3.CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION))

NG

5.INSPECT RELAY (EFI MAIN1)
3.CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION))
a.

Disconnect the ECM connector.


b.

Disconnect the fuel injector assembly (for port injection) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A36-12 (#10) - C8-2 Always Below 1 Ω
A36-22 (#20) - C30-2 Always Below 1 Ω
A36-32 (#30) - C9-2 Always Below 1 Ω
A36-13 (#40) - C31-2 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A36-12 (#10) or C8-2 - Body ground Always 10 kΩ or higher
A36-22 (#20) or C30-2 - Body ground Always 10 kΩ or higher
A36-32 (#30) or C9-2 - Body ground Always 10 kΩ or higher
A36-13 (#40) or C31-2 - Body ground Always 10 kΩ or higher




OK

4.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
a.

Inspect the fuel injector assembly (for port injection) (See page Engine / Hybrid System>FA20 FUEL>FUEL INJECTOR(for Port Injection)>INSPECTION).



OK

NG

REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)

5.INSPECT RELAY (EFI MAIN1)

OK

6.CHECK HARNESS AND CONNECTOR (EFI MAIN1 RELAY - FUEL INJECTOR ASSEMBLY)

NG

REPLACE RELAY (EFI MAIN1)

6.CHECK HARNESS AND CONNECTOR (EFI MAIN1 RELAY - FUEL INJECTOR ASSEMBLY)
a.

Disconnect the fuel injector assembly (for port injection) connector.


b.

Remove the EFI MAIN1 relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
C8-1 - EFI MAIN1 relay terminal 3 Always Below 1 Ω
C30-1 - EFI MAIN1 relay terminal 3 Always Below 1 Ω
C9-1 - EFI MAIN1 relay terminal 3 Always Below 1 Ω
C31-1 - EFI MAIN1 relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
C8-1 or EFI MAIN1 relay terminal 3 - Body ground Always 10 kΩ or higher
C30-1 or EFI MAIN1 relay terminal 3 - Body ground Always 10 kΩ or higher
C9-1 or EFI MAIN1 relay terminal 3 - Body ground Always 10 kΩ or higher
C31-1 or EFI MAIN1 relay terminal 3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR