Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  P0023  Camshaft Position "B" Actuator Circuit / Open (Bank 2)  


DESCRIPTION

Refer to P000B (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P000B).

DTC No. DTC Detection Condition Trouble Area
P0013 Oil control valve current is less than 0.306 A for exhaust camshaft circuit for 2 seconds or more (bank 1).
(1 trip detection logic)
·

Open or short in camshaft timing oil control valve circuit (for exhaust side of bank 1)

·

Camshaft timing oil control valve (for exhaust side of bank 1)

·

ECM


P0023 Oil control valve current is less than 0.306 A for exhaust camshaft circuit for 2 seconds or more (bank 2).
(1 trip detection logic)
·

Open or short in camshaft timing oil control valve circuit (for exhaust side of bank 2)

·

Camshaft timing oil control valve (for exhaust side of bank 2)

·

ECM



MONITOR DESCRIPTION

This DTC is designed to detect open or short in the camshaft timing oil control valve (for exhaust camshaft) circuit. If the camshaft timing oil control valve's duty-cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

CONFIRMATION DRIVING PATTERN

1.
A283032E18
0.188,0.5 1.24,0.938 1.052,0.438 10 false Engine Speed 0.167,2.604 1.052,3.094 0.885,0.49 10 false Vehicle Speed 0.885,1.771 1.26,2 0.375,0.229 10 false Idling 0.146,1.01 1.323,1.229 1.177,0.219 10 false 2500 to 3000 rpm 3.198,0.865 3.615,1.219 0.417,0.354 10 false [A] 5.396,2.688 5.771,2.906 0.375,0.219 10 false [B] 0.073,2.906 1.292,3.104 1.219,0.198 10 false 10 km/h (6.25 mph) 0.333,3.448 1.313,3.646 0.979,0.198 10 false 0 km/h (0 mph) 2.656,4.156 3.927,4.365 1.271,0.208 10 false 40 seconds or more 4.958,4.156 6.01,4.354 1.052,0.198 10 false 1 minute or more 6.479,4.01 6.948,4.438 0.469,0.427 10 false Time

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P0013 or P0023.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280056E07
4.156,1.781 4.406,2.094 0.25,0.313 10 false 2 2.958,1.781 3.208,2.094 0.25,0.313 10 false 1 2.74,2.469 4.854,2.823 2.115,0.354 10 false Camshaft Timing Oil Control Valve (for Exhaust Side of Bank 1) 5.188,1.802 5.76,2.229 0.573,0.427 10 false OE1 4.146,3.333 4.396,3.646 0.25,0.313 10 false 2 2.979,3.333 3.229,3.646 0.25,0.313 10 false 1 2.719,4.063 4.823,4.5 2.104,0.438 10 false Camshaft Timing Oil Control Valve (for Exhaust Side of Bank 2) 5.188,0.771 5.688,1.073 0.5,0.302 10 false SSHUT 5.615,4.51 6.042,4.719 0.427,0.208 10 false ECM 2.729,2.302 3.198,2.625 0.469,0.323 10 false C5 2.708,3.885 3.156,4.177 0.448,0.292 10 false C23 4.813,1.896 5.25,2.219 0.438,0.323 10 false A36 4.823,3.448 5.344,3.823 0.521,0.375 10 false A36 4.823,0.875 5.271,1.208 0.448,0.333 10 false A35 4.917,1.677 5.167,1.99 0.25,0.313 10 false 7 4.917,3.229 5.167,3.542 0.25,0.313 10 false 5 4.854,0.667 5.208,1.031 0.354,0.365 10 false 13 5.188,3.354 5.625,3.729 0.438,0.375 10 false OE2 1.125,5.146 1.948,5.5 0.823,0.354 10 false EFI (CTRL) 1.26,3.979 2.042,4.281 0.781,0.302 10 false EFI MAIN1 1.271,5.99 2.052,6.292 0.781,0.302 10 false Battery 1.031,3.646 1.281,3.958 0.25,0.313 10 false 3 1.031,4.302 1.281,4.615 0.25,0.313 10 false 5 0.521,3.646 0.771,3.958 0.25,0.313 10 false 1 0.521,4.302 0.771,4.615 0.25,0.313 10 false 2

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0013 is displayed, check the exhaust camshaft circuit for the right bank VVT system (bank 1).

·

If DTC P0023 is displayed, check the exhaust camshaft circuit for the left bank VVT system (bank 2).

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.READ DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTC after recording the freeze frame data and DTC.


e.

Turn the ignition switch off.


f.

Start the engine and allow the engine to idle.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read DTCs.

Result
Result Proceed to
DTC P0013 or P0023 is output A
DTC is not output B



A

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE (FOR EXHAUST CAMSHAFT)

B

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE (FOR EXHAUST CAMSHAFT)
a.

Inspect the camshaft timing oil control valve (for exhaust camshaft) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT TIMING OIL CONTROL VALVE)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE (FOR EXHAUST CAMSHAFT)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT TIMING OIL CONTROL VALVE)
a.
U146744E03
0.448,0.719 0.781,0.906 0.333,0.188 10 false C5 0.125,0.073 0.49,0.271 0.365,0.198 10 false *a 0.417,1.167 0.75,1.354 0.333,0.188 10 false C23 0.833,0.698 1.198,0.896 0.365,0.198 10 false *A 0.833,1.156 1.198,1.354 0.365,0.198 10 false *B

Disconnect the camshaft timing oil control valve (for exhaust camshaft connector).


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C5-1 - Body ground Ignition switch ON 11 to 14 V
C23-1 - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*A Bank 1
*B Bank 2
*a Front view of wire harness connector
(to Camshaft Timing Oil Control Valve)


OK

4.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)

NG

5.INSPECT RELAY (EFI MAIN1)
4.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)
a.

Disconnect the camshaft timing oil control valve (for exhaust camshaft) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A36-7 (OE1) - C5-2 Always Below 1 Ω
A36-5 (OE2) - C23-2 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A36-7 (OE1) or C5-2 - Body ground Always 10 kΩ or higher
A36-5 (OE2) or C23-2 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT RELAY (EFI MAIN1)

OK

6.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - EFI MAIN1 RELAY)

NG

REPLACE RELAY (EFI MAIN1)

6.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - EFI MAIN1 RELAY)
a.

Disconnect the ECM connector.


b.

Remove the EFI MAIN1 relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
EFI MAIN1 relay terminal 3 - C5-1 Always Below 1 Ω
EFI MAIN1 relay terminal 3 - C23-1 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
EFI MAIN1 relay terminal 3 or C5-1 - Body ground Always 10 kΩ or higher
EFI MAIN1 relay terminal 3 or C23-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR