The Variable Valve Timing (VVT) system adjusts the exhaust valve timing to improve driveability. The engine oil pressure turns the VVT controller to adjust the valve timing.
The camshaft timing oil control valve assembly is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time to the solenoid (duty-cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P000B | Integrated deviations in target exhaust valve timing and actual exhaust valve timing per specified time exceed threshold (bank 1).
(2 trip detection logic) |
·
Valve timing ·
Camshaft timing oil control valve assembly (for exhaust side of bank 1) ·
Camshaft oil control valve filter (bank 1) ·
Camshaft timing gear assembly (for exhaust side of bank 1) ·
ECM |
| P0014 | Deviation in target exhaust valve timing and actual exhaust valve timing exceeds threshold for 8 seconds (bank 1).
(2 trip detection logic) |
|
| P000D | Integrated deviations in target exhaust valve timing and actual exhaust valve timing per specified time exceed threshold (bank 2).
(2 trip detection logic) |
·
Valve timing ·
Camshaft timing oil control valve assembly (for exhaust side of bank 2) ·
Camshaft oil control valve filter (bank 2) ·
Camshaft timing gear assembly (for exhaust side of bank 2) ·
ECM |
| P0024 | Deviation in target exhaust valve timing and actual exhaust valve timing exceeds threshold for 8 seconds (bank 2).
(2 trip detection logic) |
The ECM optimizes the exhaust valve timing using the Variable Valve Timing (VVT) system to control the exhaust camshaft. The VVT system includes the ECM, the camshaft timing oil control valve assembly and the VVT controller (camshaft timing exhaust gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the exhaust camshaft.
If the difference between the target and actual exhaust valve timing is large, and changes in the actual exhaust valve timing are small, the ECM interprets this as a VVT controller stuck malfunction and stores a DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up until the engine oil temperature reaches 75°C (167°F) or higher.
Perform the following the confirmation driving pattern.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 10 seconds or more [A].
Accelerate the vehicle to 97 km/h (60 mph) or more within 20 seconds [B].
Drive the vehicle at 97 km/h (60 mph) or more for 20 seconds or more [C].
Release the accelerator pedal to Decelerate until the vehicle speed decreases to less than 64 km/h (40 mph) [D].
Release the accelerator pedal fully to perform the fuel-cut.
Drive the vehicle at 60 km/h (40 mph) or less for 20 seconds or more [E].
Accelerate the vehicle to 97 km/h (60 mph) or more within 10 seconds [F].
Release the accelerator pedal and stop the vehicle [G].
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P000B, P000D, P0014 or P0024.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Refer to DTC P0013 (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P0013).
If DTC P000B or P0014 is displayed, check the exhaust camshaft circuit for the right bank VVT system (bank 1).
If DTC P000D or P0024 is displayed, check the exhaust camshaft circuit for the left bank VVT system (bank 2).
DTC P0014 or P0024 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC P000B, P000D, P0014 or P0024 is output | A |
| DTC P000B, P000D, P0014 or P0024 and other DTCs are output | B |
If any DTCs other than P000B, P000D, P0014 or P0024 are output, troubleshoot those DTCs first.
A
B
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Turn the A/C switch on.
Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Exhaust Linear (Bank 1), Control the VVT Exhaust Linear (Bank 2).
Check the engine speed while operating the camshaft timing oil control valve assembly (for exhaust camshaft) using the GTS.
| GTS Operation | Specified Condition |
|---|---|
| 0 deg (CA) | Normal engine speed |
| 51 deg (CA) | Engine idles roughly or stalls |
Refer to "Data List / Active Test" [VVT Ex OCV Duty #1, VVT Ex OCV Duty #2 and VVT Ex Chg Angle #1, VVT Ex Chg Angle #2] (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
|---|---|
| DTC P000B, P000D, P0014 or P0024 is output | A |
| DTC is not output | B |
DTC P000B, P000D, P0014 or P0024 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.
A
B
OK
NG
Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).
OK
NG
Inspect the camshaft timing exhaust gear assembly (See page Engine / Hybrid System>FA20 (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).
DTC P000B, P000D, P0014 or P0024 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.
OK
NG
Replace the engine oil (See page Engine / Hybrid System>FA20 (LUBRICATION)>OIL AND OIL FILTER>REPLACEMENT).
Warm up the engine for 5 minutes, and then stop the engine.
Replace the engine oil and filter (See page Engine / Hybrid System>FA20 (LUBRICATION)>OIL AND OIL FILTER>REPLACEMENT).
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P000B, P000D, P0014 or P0024 is output | B |
DTC P000B, P000D, P0014 or P0024 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.
A
B