Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM › from 2016.06
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P2101  Throttle Actuator Control Motor Circuit Range/Performance  P2102  Throttle Actuator Control Motor Circuit Low  P2103  Throttle Actuator Control Motor Circuit High  


DESCRIPTION

The throttle actuator is operated by the ECM and opens and closes the throttle valve using gears.

The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle with motor body assembly. The throttle position sensor provides feedback to the ECM. This feedback allows the ECM to appropriately control the throttle actuator and monitor the throttle opening angle as the ECM responds to driver inputs.

HINT:

This Electronic Throttle Control System (ETCS) does not use a throttle cable.


DTC No. DTC Detection Condition Trouble Area
P2101 One of the following conditions is met (1 trip detection logic):
·

Throttle actuator current is 8 A or more.

·

Internal temperature of throttle actuator driving circuit is 175°C (347°F) or higher.


·

Throttle with motor body assembly

·

ECM


P2102 ECM is turning ETCS relay on but throttle actuator power supply voltage is 5 V or less.
(1 trip detection logic)
·

Open in throttle actuator circuit

·

Throttle with motor body assembly

·

ETCS relay

·

ECM


P2103 ECM is turning ETCS relay off but throttle actuator power supply voltage is 5 V or more.
(1 trip detection logic)
·

Short in throttle actuator circuit

·

Throttle with motor body assembly

·

ETCS relay

·

ECM



MONITOR DESCRIPTION

The ECM monitors the electrical current through the electronic actuator, and detects malfunctions and open circuits in the throttle actuator based on this value. If the current is outside the standard range, the ECM determines that there is a malfunction in the throttle actuator. In addition, if the throttle valve does not function properly (for example, stuck on), the ECM determines that there is a malfunction. The ECM then illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

1.
A283035E07
3.958,0.854 4.26,1.073 0.302,0.219 10 false [A] 3.51,2.344 4.833,2.688 1.323,0.344 10 false 1 minute or more 0.313,1.073 1.063,1.469 0.75,0.396 10 false 10 km/h (6.25 mph) 0.479,1.688 1.031,2.063 0.552,0.375 10 false 0 km/h (0 mph) 0.125,0.115 1.167,0.385 1.042,0.271 10 false Vehicle Speed

2.

Connect the GTS to the DLC3.

3.

Turn the ignition switch to ON and turn the GTS on.

4.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

5.

Turn the ignition switch off and wait for at least 30 seconds.

6.

Turn the ignition switch to ON and turn the GTS on.

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

8.

Depress the accelerator pedal fully and release the accelerator pedal.

9.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [A].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Enter the following menus: Powertrain / Engine / Trouble Codes.

11.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



12.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

13.

Input the DTC: P2101, P2102 or P2103.

14.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



15.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




FAIL-SAFE

When either of these DTCs or other DTCs relating to ETCS (Electronic Throttle Control System) malfunctions are stored, the ECM enters fail-safe mode. During fail-safe mode, the ECM cuts the current to the throttle actuator, and the throttle valve is returned to a fully closed throttle angle by the return spring. The ECM then adjusts the engine output by controlling the fuel injection (intermittent fuel-cut) and ignition timing, in accordance with the accelerator pedal opening angle, to allow the vehicle to continue running at a minimal speed. If the accelerator pedal is depressed firmly and gently, the vehicle can be driven slowly.

Fail-safe mode continues until a pass condition is detected, and the ignition switch is then turned off.

WIRING DIAGRAM

A392759E02
5.271,0.49 5.813,0.792 0.542,0.302 10 false SSHUT 4.917,0.604 5.188,0.781 0.271,0.177 10 false A35 4.948,0.406 5.198,0.719 0.25,0.313 10 false 13 1.094,1.896 2.01,2.198 0.917,0.302 10 false EFI MAIN1 1.104,4.604 1.885,4.906 0.781,0.302 10 false Battery 0.948,2.865 1.802,3.167 0.854,0.302 10 false EFI(CTRL) 1.979,2.875 2.49,3.177 0.51,0.302 10 false ETCS 2.844,2.229 3.281,2.531 0.438,0.302 10 false ETCS 5.281,4.667 5.969,4.969 0.688,0.302 10 false E01 4.917,4.781 5.188,4.958 0.271,0.177 10 false A36 4.99,4.583 5.24,4.896 0.25,0.313 10 false 4 5.281,5.167 6,5.469 0.719,0.302 10 false E02 4.917,5.271 5.188,5.448 0.271,0.177 10 false A36 4.99,5.073 5.24,5.385 0.25,0.313 10 false 3 5.281,3.49 5.771,3.792 0.49,0.302 10 false M+ 4.917,4.177 5.188,4.354 0.271,0.177 10 false A36 5,3.406 5.25,3.719 0.25,0.313 10 false 2 5.281,4.063 5.771,4.365 0.49,0.302 10 false M- 2.917,3.51 3.406,3.813 0.49,0.302 10 false M+ 2.938,4.073 3.427,4.375 0.49,0.302 10 false M- 4.917,3.594 5.188,3.771 0.271,0.177 10 false A36 5,3.958 5.25,4.271 0.25,0.313 10 false 1 1.948,4.729 3.646,5.385 1.698,0.656 10 false Throttle Actuator (Throttle with Motor Body Assembly 5.802,5.99 6.448,6.24 0.646,0.25 10 false ECM 1.938,4.573 2.281,4.75 0.344,0.177 10 false C15 3.219,4.063 3.563,4.24 0.344,0.177 10 false 1 3.219,3.5 3.563,3.677 0.344,0.177 10 false 2 5.281,1.281 5.792,1.583 0.51,0.302 10 false MCR 4.927,1.406 5.198,1.583 0.271,0.177 10 false A35 4.948,1.208 5.198,1.521 0.25,0.313 10 false 17 5.281,1.76 5.781,2.063 0.5,0.302 10 false +BM 4.917,1.865 5.188,2.042 0.271,0.177 10 false A35 4.99,1.667 5.24,1.979 0.25,0.313 10 false 7 3.406,1.302 3.75,1.479 0.344,0.177 10 false 1 3.396,1.771 3.74,1.948 0.344,0.177 10 false 3 2.594,1.292 2.938,1.469 0.344,0.177 10 false 2 2.594,1.781 2.938,1.958 0.344,0.177 10 false 5 0.448,1.552 0.792,1.729 0.344,0.177 10 false 1 0.896,2.229 1.24,2.406 0.344,0.177 10 false 5 0.448,2.24 0.792,2.417 0.344,0.177 10 false 2 0.885,1.552 1.229,1.729 0.344,0.177 10 false 3 0.979,3.75 1.76,4.052 0.781,0.302 10 false MAIN

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

The throttle actuator current (Throttle Motor Current) and the throttle actuator duty ratio (Throttle Motor Duty (Open) / Throttle Motor Duty (Close)) can be read using the GTS. However, the ECM shuts off the throttle actuator current when the electronic throttle control system malfunctions.



PROCEDURE

1.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF THROTTLE WITH MOTOR BODY ASSEMBLY)
a.
U190121E02
1.177,0.958 0.969,1.76 true 1.281,0.344 1.573,0.531 0.292,0.188 10 false C35 0.698,1.792 1.26,1.979 0.563,0.188 10 false 7 (+BM) 0.135,0.125 0.698,0.313 0.563,0.188 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C35-7 (+BM) - Body ground Ignition switch ON 11 to 14 V



Text in Illustration
*a Component with harness connected
(ECM)


OK

2.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)

NG

6.INSPECT RELAY (ETCS)
2.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (RESISTANCE OF THROTTLE ACTUATOR)
a.

Inspect the throttle with motor body assembly (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>THROTTLE BODY>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)

NG

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (THROTTLE WITH MOTOR BODY ASSEMBLY - ECM)
a.

Disconnect the throttle with motor body assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
C15-2 (M+) - A36-2 (M+) Always Below 1 Ω
C15-1 (M-) - A36-1 (M-) Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
C15-2 (M+) or A36-2 (M+) - Body ground Always 10 kΩ or higher
C15-1 (M-) or A36-1 (M-) - Body ground Always 10 kΩ or higher




OK

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)
a.

Check for foreign objects between the throttle valve and the housing.

OK:

No foreign objects between the throttle valve and housing.




OK

5.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)

NG

REMOVE FOREIGN OBJECT

5.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY (THROTTLE VALVE)
a.

Check if the throttle valve opens and closes smoothly.

OK:

Throttle valve opens and closes smoothly.




OK

NG

REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY

6.INSPECT RELAY (ETCS)

OK

7.CHECK HARNESS AND CONNECTOR (ETCS RELAY - EFI MAIN1 RELAY - BATTERY)

NG

REPLACE RELAY (ETCS)

7.CHECK HARNESS AND CONNECTOR (ETCS RELAY - EFI MAIN1 RELAY - BATTERY)
a.
A280105E03
0.427,0.49 0.76,0.719 0.333,0.229 10 false *1 0.49,3.396 0.823,3.625 0.333,0.229 10 false *2

Remove the ETCS relay from the engine room relay block assembly.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
5 (ETCS relay holder) - Body ground Always 11 to 14 V
2 (ETCS relay holder) - Body ground Ignition switch ON 11 to 14 V


Result:
Result Proceed to
Normal A
ETCS relay terminal 5 is abnormal. B
ETCS relay terminal 2 is abnormal. C



Text in Illustration
*1 Engine room relay block assembly
*2 ETCS relay terminal


A

8.CHECK HARNESS AND CONNECTOR (ECM - ETCS RELAY)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

9.INSPECT RELAY (EFI MAIN1)
8.CHECK HARNESS AND CONNECTOR (ECM - ETCS RELAY)
a.

Disconnect the ECM connector.


b.

Remove the ETCS relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A35-17 (MCR) - ETCS relay terminal 1 Always Below 1 Ω
A35-7 (+BM) - ETCS relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A35-17 (MCR) or ETCS relay terminal 1 - Body ground Always 10 kΩ or higher
A35-7 (+BM) or ETCS relay terminal 3 - Body ground Always 10 kΩ or higher




OK

9.INSPECT RELAY (EFI MAIN1)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT RELAY (EFI MAIN1)

OK

10.CHECK HARNESS AND CONNECTOR (ETCS RELAY - EFI MAIN1 RELAY)

NG

REPLACE RELAY (EFI MAIN1)

10.CHECK HARNESS AND CONNECTOR (ETCS RELAY - EFI MAIN1 RELAY)
a.

Remove the ETCS relay from the engine room relay block assembly.


b.

Remove the EFI MAIN1 relay from the engine room relay block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
ETCS relay terminal 2 - EFI MAIN1 relay terminal 3 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
ETCS relay terminal 2 or EFI MAIN1 relay terminal 3 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR