Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P014C  A/F Sensor Slow Response - Rich to Lean Bank 1 Sensor 1  P014D  A/F Sensor Slow Response - Lean to Rich Bank 1 Sensor 1  P015A  A/F Sensor Delayed Response - Rich to Lean Bank 1 Sensor 1  P015B  A/F Sensor Delayed Response - Lean to Rich Bank 1 Sensor 1  


DESCRIPTION

Refer to DTC P2195 (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P2195).

DTC No. DTC Detection Condition Trouble Area
P014C The "Rich to Lean response rate deterioration level*" value is standard or less for 70 seconds.
(2 trip detection logic)
·

Air fuel ratio sensor

·

Air fuel ratio sensor heater

·

ECM


P014D The "Lean to Rich response rate deterioration level*" value is standard or more for 70 seconds.
(2 trip detection logic)
P015A The "Rich to Lean delay level*" value is standard or more.
(2 trip detection logic)
P015B The "Lean to Rich delay level*" value is standard or more.
(2 trip detection logic)

*: Calculated by ECM based on the air fuel ratio sensor output.

MONITOR DESCRIPTION

The ECM monitors the time required for the A/F sensor output to change from Rich to Lean, or from Lean to Rich. When "Rich to Lean response rate deterioration level" or "Rich to Lean delay level" exceeds the threshold, the ECM stores a DTC and illuminates the MIL.

A282264E04
1.74,4.823 3.052,5.156 1.313,0.333 10 false P014C and P014D: 3.427,5.01 4.292,5.344 0.865,0.333 10 false Lean side 3.427,6.031 4.292,6.365 0.865,0.333 10 false Rich side 0.542,0.677 1.313,1.01 0.771,0.333 10 false Pattern 2.375,0.667 3.688,1 1.313,0.333 10 false Slow Response 5.125,0.667 6.438,1 1.313,0.333 10 false Delayed Start 0.323,2.625 1.167,2.958 0.844,0.333 10 false Asymmetric 0.333,5.365 1.177,5.698 0.844,0.333 10 false Symmetric 1.26,1.771 1.688,2.396 0.427,0.625 10 false Rich to Lean 1.271,3.49 1.698,4.135 0.427,0.646 10 false Lean to Rich 1.781,1.281 2.646,1.615 0.865,0.333 10 false P014C: 3.458,1.438 4.323,1.771 0.865,0.333 10 false Lean side 3.458,2.542 4.323,2.875 0.865,0.333 10 false Rich side 4.396,1.271 5.26,1.604 0.865,0.333 10 false P015A: 6.083,1.427 6.948,1.76 0.865,0.333 10 false Lean side 6.073,2.521 6.938,2.854 0.865,0.333 10 false Rich side 1.771,3.042 2.635,3.375 0.865,0.333 10 false P014D: 3.458,3.302 4.323,3.635 0.865,0.333 10 false Lean side 3.458,4.271 4.323,4.604 0.865,0.333 10 false Rich side 4.396,3.042 5.26,3.375 0.865,0.333 10 false P015B: 6.063,3.292 6.927,3.625 0.865,0.333 10 false Lean side 6.073,4.271 6.938,4.604 0.865,0.333 10 false Rich side 4.396,4.823 5.708,5.156 1.313,0.333 10 false P015A and P015B: 6.083,4.99 6.948,5.323 0.865,0.333 10 false Lean side 6.094,6.01 6.958,6.344 0.865,0.333 10 false Rich side 0.875,6.781 1.74,7.115 0.865,0.333 10 false : Normal 0.875,7.156 1.74,7.49 0.865,0.333 10 false : Malfunction

CONFIRMATION DRIVING PATTERN

A280672E03
3.25,0.5 3.552,0.719 0.302,0.219 10 false [A] 5.49,1.573 5.792,1.792 0.302,0.219 10 false [B] 2.792,2.365 4.302,2.583 1.51,0.219 10 false 20 minutes or more 5.01,2.365 6.365,2.583 1.354,0.219 10 false 1 minute or more 0.063,0.667 1.198,1.063 1.135,0.396 10 false 80 km/h (50 mph) 0.219,1.688 1.219,2.063 1,0.375 10 false 0 km/h (0 mph) 0.177,0.115 1.188,0.51 1.01,0.396 10 false Vehicle Speed 6.385,2.24 7.104,2.635 0.719,0.396 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

Check the engine coolant temperature is 20°C (68°F) or less at engine started.


7.

Perform the following the confirmation driving pattern.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


(a)

Drive the vehicle at 80 km/h (50 mph) or more for 20 minutes or more [A].

(b)

Stop the vehicle.

(c)

Idle the engine for 1 minute or more [B].


8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P014C, P014D, P015A or P015B.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the engine was warmed up or not, whether the air fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P014C, P014D, P015A OR P015B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P014C, P014D, P015A or P015B is output A
DTC P014C, P014D, P015A or P015B and other DTCs are output B


HINT:

If any DTCs other than DTC P014C, P014D, P015A or P015B are output, troubleshoot those DTCs first.




A

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

B

2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)

OK

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

NG

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

OK

4.CHECK AIR FUEL RATIO SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (AIR FUEL RATIO SENSOR - ECM)

4.CHECK AIR FUEL RATIO SENSOR
a.

Check that the proper air fuel ratio sensor is installed to the vehicle.



OK

5.PERFORM CONFIRMATION DRIVING PATTERN

NG

SECURELY REINSTALL AIR FUEL RATIO SENSOR

5.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to the Confirmation Driving Pattern.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


e.

Read the DTCs.

Result:
Result Proceed to
DTC P014C, P014D, P015A or P015B is output A
DTC is not output B




A

7.REPLACE AIR FUEL RATIO SENSOR

B

7.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

8.PERFORM CONFIRMATION DRIVING PATTERN
8.PERFORM CONFIRMATION DRIVING PATTERN
a.

Drive the vehicle according to the Confirmation Driving Pattern.



NEXT

9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
9.CHECK WHETHER DTC OUTPUT RECURS (DTC P014C, P014D, P015A OR P015B)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes / Pending.


e.

Read the DTCs.

Result:
Result Proceed to
DTC is not output A
DTC P014C, P014D, P015A or P015B is output B




A

END

B

CHECK ENGINE TO DETERMINE CAUSE OF EXTREMELY RICH OR LEAN ACTUAL AIR FUEL RATIO