Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P2195  Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1)  P2196  Oxygen (A/F) Sensor Signal Stuck Rich (Bank 1 Sensor 1)  


DESCRIPTION

HINT:
·

Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.

·

Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.



The air fuel ratio sensor generates a voltage* that corresponds to the actual air fuel ratio. This sensor voltage is used to provide the ECM with feedback so that it can control the air fuel ratio. The ECM determines the deviation from the stoichiometric air fuel ratio level, and regulates the fuel injection time. If the air fuel ratio sensor malfunctions, the ECM is unable to control the air fuel ratio accurately.

The air fuel ratio sensor is the planar type and is integrated with the heater, which heats the solid electrolyte (zirconia element). This heater is controlled by the ECM. When the intake air volume is low (the exhaust gas temperature is low), a current flows into the heater to heat the sensor, in order to facilitate accurate oxygen concentration detection. In addition, the sensor and heater portions are the narrow type. The heat generated by the heater is conducted to the solid electrolyte through the alumina, and therefore the sensor activation is accelerated.

In order to obtain a high purification rate of the carbon monoxide (CO), hydrocarbon (HC) and nitrogen oxide (NOx) components in the exhaust gas, a three-way catalytic converter is used. For the most efficient use of the three-way catalytic converter, the air fuel ratio must be precisely controlled so that it is always close to the stoichiometric level.

*: Value changes inside the ECM. Since the air fuel ratio sensor is a current output element, the current is converted into a voltage inside the ECM. Any measurements taken at the air fuel ratio sensor or ECM connectors will show a constant voltage.

A280658E03
1.896,2.188 2.635,2.656 true 3.333,2.375 2.823,2.656 true 4.573,2.021 5.354,1.521 5.354,1.521 4.813,1.792 true 4.688,1.792 5.167,0.646 true 4.969,2.208 5.365,1.958 true 4.781,2.5 5.49,2.333 5.49,2.333 4.615,2.479 true 4.833,2.563 5.583,2.688 true 1.333,2.052 1.896,2.396 0.563,0.344 10 false Element 5.219,0.521 6.354,0.875 1.135,0.354 10 false Solid Electrolyte (Zirconia Element) 5.406,1.417 6.26,1.833 0.854,0.417 10 false Alumina 5.635,2.615 6.844,2.979 1.208,0.365 10 false Atmospheric Air 5.51,2.25 6.771,2.469 1.26,0.219 10 false Platinum Electrode 5.417,1.833 5.969,2.052 0.552,0.219 10 false Heater 4.458,3.229 6.292,3.542 1.833,0.313 10 false A-A Cross Section 1.271,3.042 2.01,3.365 0.74,0.323 10 false Exhaust Gas 3.385,2.25 4.104,2.615 0.719,0.365 10 false Cover 2.156,3.083 2.427,3.365 0.271,0.281 10 false A 3.052,3.073 3.406,3.406 0.354,0.333 10 false A

DTC No. DTC Detection Condition Trouble Area
P2195 Lambda is less than 0.85 for 10 seconds in air fuel ratio feed back control
(2 trip detection logic)
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

Intake system

·

Fuel pressure

·

Fuel injector assembly (for port injection)

·

Fuel injector assembly (for direct injection)

·

ECM


P2196 Lambda is more than 1.15 for 10 seconds in air fuel ratio feed back control
(2 trip detection logic)

HINT:
·

When any of these DTCs is stored, check the air fuel ratio sensor voltage output by entering the following menus on the GTS: Powertrain / Engine / Data List / AFS Voltage B1S1.

·

Short-term fuel trim values can also be read using the GTS.

·

The ECM regulates the voltages at the A1A+ and A1A- terminals of the ECM to a constant level. Therefore, the air fuel ratio sensor voltage output cannot be confirmed without using the GTS.

·

If an air fuel ratio sensor malfunction is detected, the ECM stores a DTC.



MONITOR DESCRIPTION

ECM calculates lambda based on air fuel ratio sensor output voltage. If lambda is out of the thresholds for 10 seconds or more, ECM judges the air fuel ratio sensor is stuck and stores a DTC.

CONFIRMATION DRIVING PATTERN

A280672E03
3.25,0.5 3.552,0.719 0.302,0.219 10 false [A] 5.49,1.573 5.792,1.792 0.302,0.219 10 false [B] 2.792,2.365 4.302,2.583 1.51,0.219 10 false 20 minutes or more 5.01,2.365 6.365,2.583 1.354,0.219 10 false 1 minute or more 0.063,0.667 1.198,1.063 1.135,0.396 10 false 80 km/h (50 mph) 0.219,1.688 1.219,2.063 1,0.375 10 false 0 km/h (0 mph) 0.177,0.115 1.188,0.51 1.01,0.396 10 false Vehicle Speed 6.385,2.24 7.104,2.635 0.719,0.396 10 false Time

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on.

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

HINT:

Check the engine coolant temperature is 20°C (68°F) or less at engine started.


7.

Perform the following the confirmation driving pattern.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


(a)

Drive the vehicle at 80 km/h (50 mph) or more for 20 minutes or more [A].

(b)

Stop the vehicle.

(c)

Idle the engine for 1 minute or more [B].


8.

Enter the following menus: Powertrain / Engine / Trouble Codes.

9.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P2195 or P2196.

12.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



13.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Sensor 1 refers to the sensor closest to the engine assembly.

·

Sensor 2 refers to the sensor farthest away from the engine assembly.

·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A low air fuel ratio sensor voltage could be caused by a rich air fuel mixture. Check for conditions that would cause the engine to run rich.

·

A high air fuel ratio sensor voltage could be caused by a lean air fuel mixture. Check for conditions that would cause the engine to run lean.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Read DTCs.

Result
Result Proceed to
DTC P2195 or P2196 is output A
DTC P2195 or P2196 and other DTCs are output B

HINT:

If any DTCs relating to the air fuel ratio sensor (DTCs for the air fuel ratio sensor heater or air fuel ratio sensor admittance) are output, troubleshoot those DTCs first.




A

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

2.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
a.

Has the vehicle run out of fuel in the past?



YES

3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)

NO

4.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)
3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment.

Result
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B



A

4.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)

B

DTC CAUSED BY RUNNING OUT OF FUEL

4.READ VALUE USING GTS (TEST VALUE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


f.

Enter the following menus: Powertrain / Engine / Monitor Status / O2S(A/FS) Monitor CMPL.


g.

Check that the status of O2S(A/FS) Monitor CMPL is Complete.

If the status is still Incomplete, drive the vehicle according to the driving pattern again.


h.

Enter the following menus: Powertrain / Engine / Data List / AFS Current B1S1.


i.

Check the test value of the air fuel ratio sensor output current during fuel-cut.

Result
Result Proceed to
Within normal range (0.7 mA or higher, and lower than 2.2 mA) A
Outside normal range (lower than 0.7 mA, or 2.2 mA or higher) B



A

5.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)

B

16.REPLACE AIR FUEL RATIO SENSOR
5.READ VALUE USING GTS (OUTPUT VOLTAGE OF AIR FUEL RATIO SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Turn the GTS on.


d.

Warm up the air fuel ratio sensor at an engine speed of 2500 rpm for 90 seconds.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the Injection Volume.


f.

Perform the Control the Injection Volume operation with the engine idling.


g.

Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.

HINT:
·

Change the fuel injection volume within the range of -12.5% to +12.5%. The injection volume can be changed in fine gradations.

·

The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.

·

If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.



GTS Display (Sensor) Injection Volume Status Voltage
AFS Voltage B1S1
(Air fuel ratio)
+12.5% Rich Below 2.0 V
AFS Voltage B1S1
(Air fuel ratio)
-12.5% Lean Higher than 2.4 V
O2S B1S2
(Heated oxygen)
+12.5% Rich Higher than 0.55 V
O2S B1S2
(Heated oxygen)
-12.5% Lean Below 0.4 V

Result
Status of AFS Voltage B1S1 Status of O2S B1S2 Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition Proceed to
Lean Lean Actual air fuel ratio lean A
Rich Rich Actual air fuel ratio rich A
Lean Lean/Rich Air fuel ratio sensor malfunction B
Rich Lean/Rich Air fuel ratio sensor malfunction B
Lean/Rich Lean/Rich Normal B

Lean: During the Control the Injection Volume Active Test, the air fuel ratio sensor output voltage (AFS Voltage) is consistently higher than 2.4 V, and the heated oxygen sensor output voltage (O2S) is consistently below 0.4 V.

Rich: During the Control the Injection Volume Active Test, the AFS Voltage is consistently below 2.0 V, and the O2S is consistently higher than 0.55 V.

Lean/Rich: During the Control the Injection Volume Active Test, the output voltage of the heated oxygen sensor alternates correctly.



HINT:

Refer to "Data List / Active Test" [AFS Voltage B1S1 and O2S B1S2] (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).



A

6.CHECK INTAKE SYSTEM

B

16.REPLACE AIR FUEL RATIO SENSOR
6.CHECK INTAKE SYSTEM
a.

Check the intake system for vacuum leaks (See page Engine / Hybrid System>FA20 INTAKE / EXHAUST>INTAKE SYSTEM>ON-VEHICLE INSPECTION).

OK:

No leaks in the intake system.




OK

7.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE INTAKE SYSTEM

7.CHECK FOR EXHAUST GAS LEAK
a.

Check for exhaust gas leaks.

OK:

No gas leaks.




OK

8.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)

NG

REPAIR OR REPLACE EXHAUST SYSTEM

8.CHECK FUEL PRESSURE (LOW PRESSURE SIDE)
a.

Check the fuel pressure (low pressure side) (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).



OK

9.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)

NG

18.CHECK FUEL LINE
9.INSPECT FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)
a.

Check the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor) (See page Engine / Hybrid System>FA20 FUEL>FUEL INJECTOR(for Port Injection)>INSPECTION).



OK

10.CHECK FUEL PRESSURE (HIGH PRESSURE SIDE)

NG

REPLACE FUEL INJECTOR ASSEMBLY (FOR PORT INJECTION)

10.CHECK FUEL PRESSURE (HIGH PRESSURE SIDE)
a.

Check the fuel pressure (high pressure side) (See page Engine / Hybrid System>FA20 FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION).



OK

11.INSPECT FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)

NG

REPAIR OR REPLACE FUEL SYSTEM (HIGH PRESSURE SIDE)

11.INSPECT FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)
a.

Check the fuel injector assembly (for direct injection) (See page Engine / Hybrid System>FA20 FUEL>FUEL INJECTOR(for Direct Injection)>INSPECTION).



OK

12.REPLACE AIR FUEL RATIO SENSOR

NG

REPLACE FUEL INJECTOR ASSEMBLY (FOR DIRECT INJECTION)

12.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
13.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment.

Result
Result Proceed to
ABNORMAL (DTC P2195 or P2196 is output) A
NORMAL (DTC is not output) B



A

14.REPLACE ECM

B

END

14.REPLACE ECM

NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment.

Result
GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit





NEXT

END

16.REPLACE AIR FUEL RATIO SENSOR
a.


NEXT

17.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
17.CHECK WHETHER DTC OUTPUT RECURS (DTC P2195 OR P2196)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.



e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the GTS on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


k.

Input the DTC: P2195 or P2196.


l.

Check the DTC judgment.

Result
Result Proceed to
NORMAL (DTC is not output) A
ABNORMAL (DTC P2195 or P2196 is output) B



A

END

B

18.CHECK FUEL LINE
a.

Check the fuel lines for leaks or blockage.



OK

REPLACE FUEL PUMP ASSEMBLY

NG

REPAIR OR REPLACE FUEL LINE