Refer to DTC P2195 (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P2195).
When any of these DTCs is stored, the ECM enters fail-safe mode. The ECM turns off the air fuel ratio sensor heater in fail-safe mode. Fail-safe mode continues until the ignition switch is turned off.
Although the DTC titles say oxygen sensor, these DTCs relate to the air fuel ratio sensor.
Sensor 1 refers to the sensor mounted in front of the three-way catalytic converter and located near the engine assembly.
The ECM provides a pulse width modulated control circuit to adjust the current through the heater. The air fuel ratio sensor heater circuit uses a relay on the +B side of the circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| P0030 | Air fuel ratio sensor impedance is greater than 65 Ω for 10 seconds or more.
(2 trip detection logic) |
·
Open or short in air fuel ratio sensor circuit ·
Air fuel ratio sensor ·
ECM |
| P0031 | Air fuel ratio sensor heater voltage is less than 1.2 V for 1 second or more.
(1 trip detection logic) |
|
| P0032 | Air fuel ratio sensor heater voltage is 1.2 V or more for 2 seconds or more.
(1 trip detection logic) |
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
The ECM uses information from the air fuel ratio sensor to regulate the air fuel ratio and keep it close to the stoichiometric level. This maximizes the ability of the three-way catalytic converter to purify the exhaust gases.
The air fuel ratio sensor detects oxygen levels in the exhaust gas and transmits the information to the ECM. The inner surface of the sensor element is exposed to the outside air. The outer surface of the sensor element is exposed to the exhaust gas. The sensor element is made of platinum-coated zirconia and includes an integrated heating element.
The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations between the exhaust gas and outside air. The platinum coating amplifies this voltage generation.
The air fuel ratio sensor is more efficient when heated. When the exhaust gas temperature is low, the sensor cannot generate useful voltage signals without supplementary heating. The ECM regulates the supplementary heating using a duty-cycle approach to adjust the average current in the sensor heater element. If the heater current is outside the normal range, the signal transmitted by the air fuel ratio sensor becomes inaccurate. As a result, the ECM is unable to regulate the air fuel ratio properly.
When the current in the air fuel ratio sensor heater is outside the normal operating range, the ECM interprets this as a malfunction in the sensor heater and stores a DTC.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].
Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input the DTC: P0030, P0031 or P0032.
Check the DTC judgment result.
| GTS Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
If a permanent DTC is output, the system is malfunctioning.
If no permanent DTC is output, the system is normal.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Refer to "Data List / Active Test" [A/F Heater Duty #1] (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).
Sensor 1 refers to the sensor closest to the engine assembly.
Sensor 2 refers to the sensor farthest away from the engine assembly.
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Change the fuel injection volume using the Control the Injection Volume function provided in the Active Test and monitor the air fuel ratio sensor output voltage (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>P0137). If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.
Inspect the air fuel ratio sensor (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION).
OK
NG
Disconnect the air fuel ratio sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C14-2 (+B) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
OK
NG
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-5 (HA1A) - C14-1(HA1A) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A34-5 (HA1A) or C14-1 (HA1A) - Body ground | Always | 10 kΩ or higher |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P0030, P0031or P0032 is output | B |
A
B
Check the EFI MAIN2 relay (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).
OK
NG
Disconnect the air fuel ratio sensor connector.
Remove the EFI MAIN2 relay from the engine room relay block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI MAIN2 relay terminal 3 - C14-2 (+B) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| EFI MAIN2 relay terminal 3 or C14-2 (+B) - Body ground | Always | 10 kΩ or higher |
OK
NG