Home › Engine / Hybrid System › FA20 (ENGINE CONTROL) › SFI SYSTEM
RM2090E _51 Engine / Hybrid System _060665 FA20 ENGINE CONTROL _0297470 SFI SYSTEM C

FA20 ENGINE CONTROL  SFI SYSTEM  P0851  Park / Neutral Switch Input Circuit Low  P0852  Park / Neutral Switch Input Circuit High  


DESCRIPTION

DTC No. DTC Detection Condition Trouble Area
P0851
for Manual Transmission

No non-neutral position detected in shift change running state (judged based on changes in the relationship between vehicle speed and engine speed) (2 trip detection logic)


for Automatic Transmission

The CAN data received from the TCM is "P or N" position signal while the park/neutral position switch assembly is not in P or N position. (2 trip detection logic)


for Manual Transmission
·

Open or short in neutral position switch signal circuit

·

Neutral position switch

·

ECM


for Automatic Transmission
·

Open or short in park/neutral position switch signal circuit

·

Park/neutral position switch assembly

·

ECM

·

TCM


P0852
for Manual Transmission

No neutral position detected in shift change running state (judged based on changes in the relationship between vehicle speed and engine speed) (2 trip detection logic)


for Automatic Transmission

The CAN data received from the TCM is other than "P or N" position signal while the park/neutral position switch assembly is in P or N position. (2 trip detection logic)


for Manual Transmission
·

Open or short in neutral position switch signal circuit

·

Neutral position switch

·

ECM


for Automatic Transmission
·

Open or short in park / neutral position switch signal circuit

·

Park/neutral position switch assembly

·

ECM

·

TCM



MONITOR DESCRIPTION

for Manual Transmission

The ECM detects the shift change status from the neutral position switch signal, and detects the current selected gear from the engine speed and vehicle speed. If the neutral position switch signal and the shift change status cannot be coordinated, the ECM interprets this as a malfunction, illuminates the MIL, and stores the DTC.


for Automatic Transmission

If the ECM cannot coordinate the N, P or neutral information from the park/neutral position switch signal with the shift information sent from the TCM through CAN communication, then the ECM interprets this as a malfunction, illuminates the MIL, and stores the DTC.


CONFIRMATION DRIVING PATTERN

1.
A283034E03
2.458,2.281 2.563,2.448 2.563,2.448 2.885,2.448 false 4.844,0.104 6.667,0.396 1.823,0.292 12 false for Manual Transmission: 0.146,0.26 1.271,0.635 1.125,0.375 10 false Vehicle Speed 2.948,2.365 5.719,2.635 2.771,0.271 10 false Change gear position 3 times or more. 2.208,1.146 2.563,1.479 0.354,0.333 10 false [A] 0.542,1.719 1.083,2.135 0.542,0.417 10 false 0 km/h (0 mph) 0.458,0.688 1.104,1.146 0.646,0.458 10 false 64 km/h (40 mph)

2.
A283035E06
4.792,0.083 7.156,0.417 2.365,0.333 12 false for Automatic Transmission: 3.583,2.354 4.854,2.719 1.271,0.365 10 false 1 minute or more 0.146,0.094 1.115,0.385 0.969,0.292 10 false Vehicle Speed 0.344,0.948 1,1.281 0.656,0.333 10 false 10 km/h (6.25 mph) 0.354,1.708 0.844,2.073 0.49,0.365 10 false 0 km/h (0 mph) 3.979,0.844 4.292,1.094 0.313,0.25 10 false [B]

3.

Connect the GTS to the DLC3.

4.

Turn the ignition switch to ON and turn the GTS on.

5.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Turn the ignition switch to ON and turn the GTS on.

8.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.

9.

Change gear position 3 times or more during Accelerating vehicle to 64 km/h (40 mph) [A]. (for Manual Transmission)

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


10.

Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B]. (for Automatic Transmission)

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


11.

Enter the following menus: Powertrain / Engine / Trouble Codes.

12.

Read pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



13.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

14.

Input the DTC: P0851 or P0852.

15.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



16.

If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (See page Engine / Hybrid System>FA20 (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

HINT:
·

If a permanent DTC is output, the system is malfunctioning.

·

If no permanent DTC is output, the system is normal.




WIRING DIAGRAM

A280098E03
1.458,1.927 3.604,2.521 2.146,0.594 10 false Neutral Position Switch 4.917,2.917 5.427,3.146 0.51,0.229 10 false ECM 1.458,1.781 1.865,2.021 0.406,0.24 10 false A54 4.417,1.333 4.813,1.667 0.396,0.333 10 false NSW 4.156,1.333 4.469,1.667 0.313,0.333 10 false 16 4.24,2.302 4.458,2.615 0.219,0.313 10 false 4 2.802,1.323 3.052,1.635 0.25,0.313 10 false 2 1.615,1.333 1.865,1.646 0.25,0.313 10 false 1 4.406,2.927 4.854,3.302 0.448,0.375 10 false A33 0.115,0.177 2.563,0.677 2.448,0.5 12 false for Manual Transmission: 4.417,2.302 4.792,2.594 0.375,0.292 10 false EC

A280656E03
2.031,2.615 3.417,3.063 1.385,0.448 10 false Park/Neutral Position Switch Assembly 5.135,2.781 5.552,3.042 0.417,0.26 10 false ECM 2.042,2.438 2.385,2.75 0.344,0.313 10 false L2 4.677,1.563 5.063,1.865 0.385,0.302 10 false NSW 4.406,1.563 4.656,1.875 0.25,0.313 10 false 16 2.76,1.823 3.01,2.135 0.25,0.313 10 false 4 2.104,2.125 2.354,2.438 0.25,0.313 10 false 5 4.677,2.781 5.042,3.094 0.365,0.313 10 false A33 0.083,0.167 2.531,0.667 2.448,0.5 12 false for Automatic Transmission:

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch assembly conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine / Data List / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.

Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF




PROCEDURE

1.CHECK VEHICLE TYPE
a.

Confirm the transmission.

Result
Result Proceed to
for Manual Transmission A
for Automatic Transmission B



A

2.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF NEUTRAL POSITION SWITCH)

B

5.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
2.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF NEUTRAL POSITION SWITCH)
a.
U146761E03
0.177,0.094 0.542,0.292 0.365,0.198 10 false *a 0.375,1.052 0.708,1.24 0.333,0.188 10 false A54

Disconnect the neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A54-1 - A54-2 Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Neutral Position Switch)



OK

3.INSPECT NEUTRAL POSITION SWITCH

NG

4.CHECK HARNESS AND CONNECTOR (NEUTRAL POSITION SWITCH - ECM)
3.INSPECT NEUTRAL POSITION SWITCH

OK

NG

4.CHECK HARNESS AND CONNECTOR (NEUTRAL POSITION SWITCH - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the neutral position switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A33-16 (NSW) - A54-2 Always Below 1 Ω
A33-4 (EC) - A54-1 Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A33-16 (NSW) or A54-2 - Body ground Always 10 kΩ or higher
A33-4 (EC) or A54-1 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT TERMINAL VOLTAGE (POWER SOURCE OF PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.
U146756E03
0.552,1.083 0.844,1.271 0.292,0.188 10 false L2 0.188,0.125 0.552,0.323 0.365,0.198 10 false *a

Disconnect the park/neutral position switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L2-4 - L2-5 Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)



OK

6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - BODY GROUND)
6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly (See page Drivetrain>TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE)>PARK / NEUTRAL POSITION SWITCH>INSPECTION).



OK

NG

7.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ECM - BODY GROUND)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for open):
Tester Connection Condition Specified Condition
A33-16 (NSW) - L2-4 Always Below 1 Ω
L2-5 - Body ground Always Below 1 Ω


Standard Resistance (Check for short):
Tester Connection Condition Specified Condition
A33-16 (NSW) or L2-4 - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR