Home › Drivetrain › TX6A (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY
RM2090E _52 Drivetrain _060674 TX6A AUTOMATIC TRANSMISSION / TRANSAXLE _0297552 AUTOMATIC TRANSMISSION ASSEMBLY A

TX6A AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C264286

Engage the splines of the input shaft and turbine runner.


b.
C264287

Engage the splines of the stator shaft and stator while turning the torque converter assembly.

HINT:

If the stator shaft splines are difficult to engage with the stator splines, move the torque converter back approximately 10 mm (0.394 in.) and engage the splines while rotating the torque converter assembly.



c.
C264288

Turn the torque converter assembly to engage the key of the oil pump drive gear into the slot on the torque converter assembly.


d.
C261634E01
2.688,1.612 2.813,1.766 0.125,0.154 10 A

Using a vernier caliper and straightedge, measure dimension A between the transmission contact surface of the engine and the torque converter contact surface of the drive plate.


e.
C261638E01
2.514,1.572 2.647,1.740 0.133,0.168 10 B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that dimension B is more than dimension A, which was measured in the first step.

Standard::

B = A + 1 mm (0.0394 in.) or more


NOTICE:
·

Make sure to deduct the thickness of the straightedge.

·

If the transmission is installed to the engine with the torque converter not sufficiently inserted, the torque converter may be damaged.




Hide 32916 2.INSTALL OIL COOLER TUBE

a.

Install the oil cooler tube with the bolt to the automatic transmission assembly.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


b.

Connect the 2 water by-pass hoses to the transmission oil cooler with the 4 hose clamps.


Hide 3.INSTALL WIRE HARNESS

C262094

a.

Install the wire harness to the automatic transmission assembly with engage the 6 wire harness clamps.


b.

Connect the park/neutral position switch connector, transmission wire connector and the transmission revolution sensor connector.

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



Hide 35000 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

a.
C261639E01
0.85,1.014 0.353,0.871 false 0.163,0.767 0.323,0.924 0.160,0.157 10 *1 2.475,0.829 2.928,0.578 false 2.937,0.456 3.097,0.612 0.160,0.157 10 *1

Confirm that 2 knock pins are on the automatic transmission assembly contact surface of the engine cylinder block before automatic transmission assembly installation.


b.

Keeping the engine assembly and the automatic transmission assembly in a horizontal position, align the knock pins with each hole on the automatic transmission assembly and install the 2 bolts and 2nuts.

Text in Illustration
*1 Knock Pin
V100135

Bolt
V100136

Nut

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)

NOTICE:
·

Make sure not to pinch or damage any wire harness.

·

Make sure the knock pin is fully engaged with the knock pin hole.

·

Do not forcibly pry the automatic transmission assembly.

·

After installing the automatic transmission assembly, confirm that the torque converter assembly can be rotated by hand.




Hide 12371 5.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear No. 1 engine mounting insulator to the automatic transmission assembly with the 4 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 12372 6.INSTALL REAR NO. 2 ENGINE MOUNTING INSULATOR

a.

Install the rear No. 2 engine mounting insulator to the rear No. 1 engine mounting insulator with 2 washers and 2 nuts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


b.

Install the rear No. 2 engine mounting insulator to the body with the 4 bolts.

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


Hide 17455 7.INSTALL EXHAUST PIPE BRACKET

a.

Install the exhaust pipe bracket with the 2 bolts.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)


Hide 33702B 8.INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

a.

Apply MP grease to the pin.


b.

Install the floor shift gear shifting rod sub-assembly to the transmission control shaft lever RH with the pin and a clip.


c.

While pushing the shift lock release button, move the shift lever to N.


d.
C257566

Using tape, hold a 0.3 mm feeler gauge on the floor shift control select lever.


e.
C257565

Using tape, attach the floor shift control select lever to the console box assembly.

NOTICE:

Make sure that the feeler gauge is not on the area shown in the illustration.



f.
C116831E01
1.866,0.104 2.035,0.265 0.170,0.161 10 N 1.573,0.13 1.743,0.290 0.170,0.161 10 R 1.152,0.226 1.322,0.387 0.170,0.161 10 P

Turn the transmission control shaft lever RH of the park/neutral position switch assembly counterclockwise until it stops, and turn it clockwise 2 notches to set it to the N position.


g.

Temporarily install the floor shift gear shifting rod sub-assembly with the nut.


h.

Tighten the nut while lightly pushing the lever rearward.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Do not push the lever too hard.



Hide 89413B 9.INSTALL TRANSMISSION REVOLUTION SENSOR (NT)

Hide 32907A 10.CONNECT OIL COOLER TUBE

a.

Fasten the oil cooler pipe with the oil cooler tube using 2 bolts.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


Hide 32943B 11.INSTALL TRANSMISSION OIL COOLER HOSE

a.

Install the 2 transmission oil cooler hoses to the transmission oil cooler with the 4 hose clamps.


Hide 35000 13.CONNECT AUTOMATIC TRANSMISSION ASSEMBLY

a.

Install the 2 bolts to the automatic transmission assembly.

Torque:
50 N*m (510 kgf*cm, 37 ft.*lbf)


Hide 32101C 14.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.

Install the 6 drive plate and torque converter setting bolt.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Make sure that the drive plate and torque converter setting bolts do not fall into the clutch housing.

·

Make sure not to damage the drive plate and torque converter setting bolts.




Hide 11361J 15.INSTALL FLYWHEEL HOUSING UNDER COVER

a.

Install the flywheel housing side cover.


Hide 44771 16.CONNECT VACUUM TUBE CONNECTOR HOSE (for LHD)

a.

Connect the vacuum tube connector hose with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 17.CONNECT WIRE HARNESS

a.

Install the No. 2 engine hanger with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 16 ft.*lbf)


b.

Install the wire harness clamp bracket with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Engage the wire harness clamp.


d.
C260567E06
2.479,1.271 2.604,1.438 0.125,0.167 10 true A

Connect the 3 connectors.

HINT:

Push down the lever until the claw of the connector (A) makes a connection sound.



e.

Engage the 4 wire harness clamps.


f.

Install the ground cable to the automatic transmission assembly with the bolt

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


g.
C260564E02
2.895,0.215 3.018,0.367 0.123,0.152 10 A

Connect the 2 connectors.

HINT:

Push down the lever until the claw of the connector (A) makes a connection sound.



Hide 48811 19.INSTALL FRONT STABILIZER BAR

Hide 37100 20.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY

Hide 51444A 21.INSTALL REAR ENGINE UNDER COVER LH (w/ Floor Under Cover)

Hide 51443C 22.INSTALL REAR ENGINE UNDER COVER RH (w/ Floor Under Cover)

HINT:

Use the same procedure for the RH side as for the LH side.


Hide 26.ADD ENGINE COOLANT