Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1246  Master Cylinder Pressure Sensor Malfunction  


DESCRIPTION

The master cylinder pressure sensor is connected to the skid control ECU in the brake actuator assembly.

C210263E07
4.021,0.781 5.677,0.979 1.656,0.198 10 false Brake Actuator Assembly 2.844,1.594 4.031,1.823 1.188,0.229 10 false Skid Control ECU 5.438,2.26 6.542,2.667 1.104,0.406 10 false Master Cylinder Pressure Sensor 0.51,1.958 1.385,2.208 0.875,0.25 10 false from Battery 0.333,2.594 1.385,2.99 1.052,0.396 10 false from Stop Light Switch 0.25,3.375 1.292,3.604 1.042,0.229 10 false to Body Ground 3.833,1.979 4.188,2.188 0.354,0.208 10 false VCM 3.833,3.021 4.188,3.229 0.354,0.208 10 false PMC 3.833,3.385 4.063,3.604 0.229,0.219 10 false E2 0.531,4.302 4.896,4.51 4.365,0.208 10 false VCM: Power Supply for Master Cylinder Pressure Sensor 0.531,4.698 3.958,4.906 3.427,0.208 10 false PMC: Master Cylinder Pressure Sensor Input 0.667,5.063 4.146,5.281 3.479,0.219 10 false E2: Master Cylinder Pressure Sensor Ground 3.833,2.667 4.146,2.833 0.313,0.167 10 false PST 0.583,5.385 3.802,5.604 3.219,0.219 10 false PST: Master Cylinder Pressure Sensor Test Signal

DTC No. DTC Detection Condition Trouble Area
C1246 Any of the following is detected:
1.

The voltage of the sensor signal is out of range (below 0.129 V, above 3.29 V).

2.

An abnormality is detected in the skid control ECU internal sensor test.

3.

The sensor signal offset value is out of range.


·

STOP fuse

·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder pressure sensor (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed. ON
Brake pedal released. OFF




OK

2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)

NG

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT)

2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Master Cylinder Sensor Master cylinder pressure sensor reading / Min.: 0.00 V, Max.: 5.00 V Brake pedal released: 0.20 to 0.40 V Reading increases when brake pedal is depressed


d.

Check that the brake fluid pressure value of the master cylinder pressure sensor observed on the GTS changes when the brake pedal is depressed.

OK:

When the pedal is depressed, the voltage displayed on the GTS increases.




OK

3.READ VALUE USING GTS (STOP LIGHT SWITCH)

NG

3.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


b.

Check that the stop light switch display observed on the GTS change according to brake pedal operation.

OK:

The GTS displays on or off according to brake pedal operation.




OK

4.RECONFIRM DTC

NG

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
4.RECONFIRM DTC

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1246 is not output. A
DTC C1246 is output. B




A

B

5.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U147148E01
0.066,0.061 0.246,0.223 0.179,0.162 10 *a 0.485,1.097 0.777,1.259 0.291,0.162 10 A13

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the noise filter connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-3 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Noise Filter)



OK

6.INSPECT NOISE FILTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

6.INSPECT NOISE FILTER

OK

7.CHECK HARNESS AND CONNECTOR (NOISE FILTER - STOP LIGHT SWITCH ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (NOISE FILTER - STOP LIGHT SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-2 - A22-1 Always Below 1 Ω
A13-1 - A22-2 Always Below 1 Ω




OK

8.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

9.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U147140E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 1.202,0.478 1.488,0.922 false 1.061,0.301 1.389,0.451 0.328,0.151 10 STP 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
Stop light switch OFF (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)