Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1249  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives stop light switch signals and uses them to determine whether or not the brakes are applied.

DTCs may be stored if one of the following occurs:

·

Stop light switch stuck on/off malfunction.

·

Accelerator pedal and brake pedal depressed simultaneously.*


HINT:

*: The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously. However, this does not indicate a malfunction.


DTC No. DTC Detection Condition Trouble Area
C1249 Any of the following is detected:
·

The vehicle speed is 10 km/h (6 mph) or more, the accelerator pedal is depressed, and the stop light switch is on for 60 seconds or more.

·

When the stop light switch is off, the master cylinder pressure is increased.


·

STOP fuse

·

Stop light switch assembly

·

Noise filter

·

Stop light switch circuit

·

Skid control ECU



WIRING DIAGRAM

C261862E03
0.292,0.594 1.146,0.917 0.854,0.323 10 false from Battery 1.823,2.688 3.969,3.073 2.146,0.385 10 false to Stop Light Circuit 2.396,2.219 4.344,2.594 1.948,0.375 10 false Stop Light Switch Assembly 2.396,2.063 3.063,2.219 0.667,0.156 10 false A22 2.677,0.844 2.792,1 0.115,0.156 10 false 2 3.813,0.823 3.927,0.979 0.115,0.156 10 false 1 2.677,0.51 2.792,0.667 0.115,0.156 10 false 3 3.813,0.51 3.927,0.667 0.115,0.156 10 false 4 2.677,1.729 2.792,1.885 0.115,0.156 10 false 1 3.813,1.729 3.927,1.885 0.115,0.156 10 false 2 2.854,1.354 3.99,1.677 1.135,0.323 10 false Noise Filter 2.875,1.188 3.469,1.344 0.594,0.156 10 false A13 5.583,0.49 5.781,0.646 0.198,0.156 10 false 30 5.583,3.125 6.365,3.313 0.781,0.188 10 false 13 5.583,2.448 6.427,2.615 0.844,0.167 10 false 38 5.844,3.219 6.573,3.406 0.729,0.188 10 false GND2 5.844,2.542 6.479,2.708 0.635,0.167 10 false GND1 5.844,0.594 6.833,0.781 0.99,0.188 10 false STP 2.083,0.75 2.865,1.083 0.781,0.333 10 false STOP 5.333,3.781 6.969,4.333 1.635,0.552 10 false Skid Control ECU (Brake Actuator Assembly) 5.365,3.583 5.729,3.771 0.365,0.188 10 false A5

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

The skid control ECU (brake actuator assembly) may store this DTC upon judging that a stuck on malfunction has occurred when the accelerator pedal and brake pedal are depressed simultaneously.

·

If the pedals were depressed simultaneously, clear the DTC because it is not a malfunction.



PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the "Stop Light SW" display observed on the GTS changes according to the brake pedal operation.

OK:

The GTS displays "ON" or "OFF" according to the brake pedal operation.




OK

2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR 1, STOP LIGHT SW)

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
2.READ VALUE USING GTS (MASTER CYLINDER PRESSURE SENSOR 1, STOP LIGHT SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Master Cylinder Pressure Sensor 1 Master cylinder pressure sensor / Min.: -1.00 MPa, Max.: 23.99 MPa Brake pedal released: -1 to 0 MPa During brake pedal operation: Proportional to pedal pressure
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-


d.

Check that the "Stop Light SW" and "Master Cylinder Pressure Sensor 1" displays observed on the GTS change according to the brake pedal operation.

OK:

When the "Stop Light SW" is turned "ON", the "Master Cylinder Pressure Sensor 1" is within the standard value (0.08 to 0.27 MPa(0.81 to 2.75 kgf/cm2, 11 to 39 psi)).




OK

3.RECONFIRM DTC

NG

ADJUST STOP LIGHT SWITCH ASSEMBLY

3.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle and depress the brake pedal several times to test the stop light circuit.


f.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC C1249 is output. A
DTC C1249 is not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE).




A

B

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U147218E03
0.167,0.052 0.354,0.208 0.188,0.156 10 false *a 0.688,1.115 1.021,1.365 0.333,0.25 10 false A13

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the noise filter connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A13-3 - Body ground Always 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Noise Filter)



OK

5.INSPECT NOISE FILTER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.INSPECT NOISE FILTER

OK

6.CHECK HARNESS AND CONNECTOR (NOISE FILTER - STOP LIGHT SWITCH ASSEMBLY)

NG

6.CHECK HARNESS AND CONNECTOR (NOISE FILTER - STOP LIGHT SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A13-2 - A22-1 Always Below 1 Ω
A13-1 - A22-2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A13-2 or A22-1 - Body ground Always 10 kΩ or higher
A13-1 or A22-2 - Body ground Always 10 kΩ or higher




OK

7.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).



OK

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
U147140E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 1.202,0.478 1.488,0.922 false 1.061,0.301 1.389,0.451 0.328,0.151 10 STP 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Reconnect the stop light switch assembly connector.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-30 (STP) - Body ground Stop light switch ON (Brake pedal depressed) 11 to 14 V*
Stop light switch OFF (Brake pedal released) Below 1.5 V


HINT:

*: The standard voltage value varies depending on the +BS terminal voltage value. The standard voltage is 85% of the +BS terminal voltage.


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)