Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › from 2016.06
RM2090E _55 Steering _060690 STEERING COLUMN _0297646 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 45250 1.INSPECT STEERING COLUMN ASSEMBLY

Hide 45250 2.INSTALL STEERING COLUMN ASSEMBLY

a.

Install the steering column assembly with the 2 nuts and new bolt.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

NOTICE:

When installing the steering column assembly, be careful that the wire harness does not interfere with or is not pinched between other parts.



b.
C260486E02
0.167,0.146 0.438,0.375 0.271,0.229 10 false *a 1.271,0.146 1.542,0.375 0.271,0.229 10 false *b

Engage the clamp.


c.

Connect the 2 connectors to the power steering ECU.

i.

As shown in the illustration, return the lock lever to its original position to connect the connector and securely push in the lock of the lock lever.



d.

Connect the each connector and engage the wire harness clamps to the steering column assembly.

Text in Illustration
*a Return the lock lever
*b Push in the lock


Hide 45260 3.INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

a.

Pass the steering intermediate shaft assembly through the hole in the body from the inside of the cabin.


b.
C260472E02
1.51,0.698 1.969,0.521 1.969,0.521 1.49,0.625 true 2,0.417 2.188,0.573 0.188,0.156 10 false *1

Connect the steering intermediate shaft assembly to the rack and pinion power steering gear assembly.

Text in Illustration
*1 Matchmark

NOTICE:

Align the matchmarks on the steering intermediate shaft assembly and the rack and pinion power steering gear assembly.



c.

Install the new bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


d.
C263656E03
1.563,0.583 2.052,0.813 2.052,0.813 1.563,0.677 true 2.104,0.792 2.292,0.948 0.188,0.156 10 false *1

Install the steering intermediate shaft assembly to the steering column assembly.

Text in Illustration
*1 Matchmark

NOTICE:

Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.



e.

Install the new bolt.

Torque:
35 N*m (357 kgf*cm, 26 ft.*lbf)


f.

Engage the 4 claws and install the dust seal.


Hide 4.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with the battery connected and the ignition switch ON.

·

Do not rotate the spiral cable without the steering wheel with the battery connected and the ignition switch ON.

·

Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.



a.

With the clamp loosened, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.


b.

Engage the claw on the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and tighten the clamp.


c.

Connect the each connector to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286 5.INSTALL UPPER STEERING COLUMN COVER

a.

Engage the 2 claws to install the upper steering column cover.


Hide 6.INSTALL LOWER STEERING COLUMN COVER

a.

w/ Knee Airbag

i.

Engage the 4 claws to install the lower steering column cover.


ii.

Install the 2 screws.



b.

w/o Knee Airbag

i.

Engage the 6 claws to install the lower steering column cover.


ii.

Install the 2 screws.



Hide 45289A 7.INSTALL STEERING COLUMN COVER SUPPORT (w/ Entry and Start System)

a.

Engage the 4 claws and install the steering column cover support.


Hide 55422 8.INSTALL UPPER INSTRUMENT PANEL METER ORNAMENT

Hide 55461A 10.INSTALL INSTRUMENT PANEL ORNAMENT (w/ Large Ornament Panel)

Hide 55405B 11.INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (w/o Large Ornament Panel)

Hide 12.TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 13.ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 14.INSPECT STEERING WHEEL CENTER POINT

Hide 15.INSTALL STEERING WHEEL ASSEMBLY

Hide 73900 16.INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)

Hide 55606 17.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)

Hide 55318C 18.INSTALL INSTRUMENT SIDE PANEL (w/o Knee Airbag)

a.
B322066

Engage the 4 clips and claw to install the instrument side panel.


Hide 22. ROTATION ANGLE SENSOR INITIALIZATION AND TORQUE SENSOR ZERO POINT CALIBRATION