If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.
With the electrical key transmitter sub-assembly in the cabin, the engine switch is pressed.
When the transmitter battery in the electrical key transmitter sub-assembly is depleted, touch the electrical key transmitter sub-assembly to the surface of the engine switch while depressing the brake pedal*1 or clutch pedal*2.
When the entry cancel function is set by customize operation, touch the electrical key transmitter sub-assembly to the surface of the engine switch while depressing the brake pedal*1 or clutch pedal*2.
*1: for Automatic Transmission
*2: for Manual Transaxle
When the battery cable is disconnected and reconnected, the power source returns to the mode it was in before the battery cable was disconnected.
| Problem Symptom | Data List Item | Active Test Item |
|---|---|---|
| Power source mode does not change to on (IG) or on (ACC) | Power Source Control
·
Start Switch1 ·
Start Switch2 ·
Latch Circuit ·
IG1 Relay Monitor(Outside) ·
IG1 Relay Monitor(Inside) ·
IG2 Relay Monitor(Outside) ·
IG2 Relay Monitor(Inside) ·
ACC Relay Monitor ·
Power Supply Condition Engine
·
Ignition Status |
- |
When using the GTS with the engine switch off to troubleshoot:
Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
The entry and start system uses multiplex communication. First perform the inspections in "How to Proceed with Troubleshooting" to confirm that there are no communication malfunctions before proceeding with troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING).
Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Entry Function)>PRECAUTION).
Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).
If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>CUSTOMIZE PARAMETERS).
After completing repairs, confirm that the problem does not reoccur.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
Check that the wireless door lock function operates normally (See page Vehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM(w/ Entry and Start System)>OPERATION CHECK).
Wireless door lock functions operate normally.
OK
NG
OK
NG
OK
NG
Remove the battery of the electrical key transmitter sub-assembly (See page Vehicle Interior>DOOR LOCK>TRANSMITTER BATTERY(w/ Entry and Start System)>REPLACEMENT).
With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter sub-assembly touch the engine switch while facing the logo side of the electrical key transmitter sub-assembly to the engine switch.
*1: for Automatic Transmission
*2: for Manual Transmission
When touch the logo of the electrical key transmitter sub-assembly to the engine switch, check whether the power source mode changes.
Power source mode changes.
If the power source mode changes, the cabin verification is malfunctioning.
| Result | Proceed to |
|---|---|
| NG (Power source mode does not change) | A |
| OK (Power source mode changes) | B |
| *A | w/o Panic Switch |
| *B | w/ Panic Switch |
A
B
for Automatic Transmission
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS tester, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light Switch1 | State of brake pedal / OFF or ON | OFF: Brake pedal released
ON: Brake pedal depressed |
·
Use this item to determine whether the stop light switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". ·
When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time. |
ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen according to the stop light switch condition.
for Manual Transmission
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Neutral SW / Clutch SW | State of clutch pedal / OFF or ON | OFF: Clutch pedal released
ON: Clutch pedal depressed |
·
Use this item to help determine if the clutch switch is malfunctioning. ·
The engine cannot be started when this item is "OFF". |
ON (clutch pedal depressed) and OFF (clutch pedal released) appear on the screen according to the stop light switch condition.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for Automatic Transmission) | B |
| NG (for Manual Transmission) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Power Supply Condition | Power Supply Condition / All OFF, IG1 ON or ACC ON, IG2 ON, ST ON, | All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)) IG1 ON: Engine switch on (IG) (IG1 relay on) IG2 ON: Engine switch on (IG) (IG2 relay on) ST ON: Sending engine start request signal |
Since IG1 ON and IG2 ON turn on at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time). |
Display changes according to the changes in the power source mode when the engine switch is pushed.
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Power Supply Condition | Power Supply Condition / All OFF, IG ON or ACC ON, IG2 ON, ST ON, | All OFF: Engine switch off (ACC and IG)
ACC ON: Engine switch on (ACC)) IG1 ON: Engine switch on (IG) (IG1 relay on) IG2 ON: Engine switch on (IG) (IG2 relay on) ST ON: Sending engine start request signal |
Since IG1 ON and IG2 ON turn on at approximately the same time, IG1 ON may not be displayed (IG1 ON turns on for a very short time). |
Measure the voltage according to the value(s) in the table below.
| *a | Component with harness connected
(Certification ECU (Smart Key ECU Assembly)) |
- | - |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| D41-6 (IG1D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| D48-9 (IG2D) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 1 V or less | |
| Engine switch on (IG) | 9 V or higher | |
| D41-4 (ACCD) - Body ground | Engine switch off | 1 V or less |
| Engine switch on (ACC) | 8.5 V or higher | |
| Engine switch on (IG) | 8.5 V or higher |
OK
NG
Remove the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).
Inspect the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>INSPECTION).
OK
NG
OK
NG
Remove the clutch start switch assembly.
for LHD (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>REMOVAL)
for RHD (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>REMOVAL)
Inspect the clutch start switch assembly.
for LHD (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for LHD)>INSPECTION)
for RHD (See page Drivetrain>CLUTCH>CLUTCH PEDAL SWITCH(for RHD)>INSPECTION)
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
A
B
C
Disconnect the D48 certification ECU (smart key ECU assembly) connector.
Disconnect the A20 clutch start switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D48-10 (CLUT) - A20-1 | Always | Below 1 Ω |
| D48-10 (CLUT) - Body ground | Always | 10 kΩ or higher |
Reconnect the A20 clutch start switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D48-10 (CLUT) - Body ground | Clutch pedal released → clutch pedal depressed | Below 1 V → 9 V or higher |
| *a | Rear view of wire harness connector
(to certification ECU (smart key ECU assembly)) |
OK
NG
Check the DTCs (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function)>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC B2784 is output | B |
| DTC B2785 is output | C |
A
B
C
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Power Source Control / Data List.
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Start Switch 1 | Condition of engine switch contact 1 / OFF or ON | OFF: Engine switch not pushed
ON: Engine switch pushed |
·
If the engine switch is pressed for a short time, the display may not change. ·
Use this item to determine whether the engine switch input signal is malfunctioning. |
| Start Switch 2 | Condition of engine switch contact 2 / OFF or ON | OFF: Engine switch not pushed
ON : Engine switch pushed |
·
Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal. ·
Behaves the same way as engine switch 1. |
The ECU data monitor changes in response to the operation of the engine switch.
| Result | Proceed to |
|---|---|
| NG | A |
| OK | B |
A
B
Remove the engine switch (See page Engine / Hybrid System>FA20 STARTING>ENGINE SWITCH>REMOVAL).
Inspect the engine switch (See page Engine / Hybrid System>FA20 STARTING>ENGINE SWITCH>INSPECTION).
OK
NG
Disconnect the D41 certification ECU (smart key ECU assembly) connector.
Disconnect the D25 engine switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D41-28 (SSW1) - D25-5 (SS1) | Always | Below 1 Ω |
| D41-30 (SSW2) - D25-1 (SS2) | Always | Below 1 Ω |
| D41-28 (SSW1) - Body ground | Always | 10 kΩ or higher |
| D41-30 (SSW2) - Body ground | Always | 10 kΩ or higher |
OK
NG