Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › from 2019.03
RM2090E _54 Brake _060684 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0297617 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).

·

The ABS control system is defective.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C264062E03
6.021,0.906 6.427,1.073 0.406,0.167 10 false CANL 6.021,1.729 6.469,1.896 0.448,0.167 10 false CANH 6.021,3.667 6.302,3.833 0.281,0.167 10 false IG1 6.021,4.604 6.427,4.771 0.406,0.167 10 false GND1 5.75,0.74 5.938,0.906 0.188,0.167 10 false 14 5.75,1.583 5.938,1.75 0.188,0.167 10 false 26 5.75,3.563 5.938,3.729 0.188,0.167 10 false 28 5.75,4.5 5.938,4.667 0.188,0.167 10 false 38 0.719,0.896 1.125,1.063 0.406,0.167 10 false CANL 0.719,1.729 1.167,1.896 0.448,0.167 10 false CANH 1.24,0.729 1.427,0.896 0.188,0.167 10 false 7 1.24,1.563 1.427,1.729 0.188,0.167 10 false 6 5.51,5.76 5.833,5.927 0.323,0.167 10 false A5 5.51,5.99 7.125,6.729 1.615,0.74 10 false Skid Control ECU (Brake Actuator Assembly) 0.125,5.771 0.448,5.938 0.323,0.167 10 false D7 0.125,5.958 1.365,6.802 1.24,0.844 10 false Combination Meter Assembly 4.333,3.813 5.323,4 0.99,0.188 10 false ECU IG1 2.188,3.646 3.229,3.833 1.042,0.188 10 false from IG1 Circuit 6.021,2.698 6.344,2.865 0.323,0.167 10 false +BS 5.75,2.594 5.938,2.76 0.188,0.167 10 false 25 4.24,2.875 5.021,3.063 0.781,0.188 10 false ABS NO. 2 2.406,2.677 3.229,2.865 0.823,0.188 10 false from Battery 2.417,6.396 4.125,6.792 1.708,0.396 10 false :CAN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication system DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

Result:
Result Proceed to
DTC is not output. A
DTC is output. B




A

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK BATTERY

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK BATTERY
a.

Check the battery voltage.

Standard Voltage:

11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)

NG

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)
a.
U147145E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 0.655,0.47 0.655,0.867 false 1.202,0.478 1.202,0.923 false 2.742,0.487 2.742,0.862 false 0.503,0.289 0.844,0.440 0.341,0.151 10 +BS 1.061,0.301 1.382,0.451 0.321,0.151 10 IG1 2.604,0.314 3.082,0.465 0.479,0.151 10 GND1 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Disconnect the skid control ECU (brake actuator assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A5-25 (+BS) - Body ground Always 11 to 14 V
A5-25 (+BS) - A5-38 (GND1) Always 11 to 14 V
A5-28 (IG1) - Body ground Ignition switch ON 11 to 14 V
A5-28 (IG1) - A5-38 (GND1) Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.
U147144E01
0.073,0.083 0.239,0.233 0.166,0.151 10 *a 2.742,0.487 2.742,0.862 false 2.518,0.314 2.984,0.465 0.467,0.151 10 GND1 1.598,0.198 1.854,0.348 0.256,0.151 10 A5

Turn the ignition switch off.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A5-38 (GND1) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))



OK

6.INSPECT COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.INSPECT COMBINATION METER ASSEMBLY
a.

Reconnect the skid control ECU (brake actuator assembly) connector.


b.

Perform an Active Test of the combination meter assembly (meter CPU) using the GTS.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST


c.

Check the combination meter assembly.

OK:

The ABS warning light turns on or off in accordance with the Active Test operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE




OK

NG

REPLACE COMBINATION METER ASSEMBLY