Home › Engine / Hybrid System › 3SZ-VE ENGINE CONTROL › SFI SYSTEM(w/ Rear Heated Oxygen Sensor) › 2011.11–2015.08
RM19Y0E _51 Engine / Hybrid System _002968 3SZ-VE ENGINE CONTROL _0014988 SFI SYSTEM(w/ Rear Heated Oxygen Sensor) C

3SZ-VE ENGINE CONTROL  SFI SYSTEM(w/ Rear Heated Oxygen Sensor)  P0133  Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 1)  


DESCRIPTION

HINT:

Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.


Refer to DTC P0130 (See page Engine / Hybrid System>3SZ-VE ENGINE CONTROL>SFI SYSTEM(w/ Rear Heated Oxygen Sensor)>P0130).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0133 Oxygen Sensor Circuit Slow Response (Bank 1 Sensor 1) All of following conditions met (2 trip detection logic):

(a) Engine warmed up

(b) After vehicle driven at vehicle speed of 10 km/h (6.2 mph) or more for 10 seconds or more

(c) While engine idling for 300 seconds or more

(d) Response time for voltage output of heated oxygen sensor to change from rich to lean or from lean to rich 1.5 seconds or more


·

Open or short in heated oxygen sensor (sensor 1) circuit

·

Heated oxygen sensor (sensor 1)

·

Heated oxygen sensor heater (sensor 1)

·

Ventilation hose

·

Fuel pressure

·

Injector

·

Ignition system

·

ECM


Comes on DTC stored

CONFIRMATION DRIVING PATTERN

A143432E08
2.896,0.323 3.708,0.833 0.813,0.51 10 10 seconds or more 3.698,2.156 5.594,2.615 1.896,0.458 10 300 seconds or more 0.906,0.49 2.052,0.938 1.146,0.448 10 Vehicle Speed 0.677,1.063 2.104,1.479 1.427,0.417 10 10 km/h (6.2 mph) 0.615,1.844 2.156,2.229 1.542,0.385 10 Ignition Switch OFF 2.115,2.135 3.375,2.615 1.26,0.479 10 Warm Up 5.323,1.99 6.25,2.406 0.927,0.417 10 Time 2.198,1.563 2.688,1.958 0.49,0.396 10 (f) 3.125,0.948 3.667,1.385 0.542,0.438 10 (g) 4.156,1.542 4.729,1.938 0.573,0.396 10 (h)

HINT:

This confirmation driving pattern is used in the "PERFORM CONFIRMATION DRIVING PATTERN" procedure of the following diagnostic troubleshooting procedure.


(a) Connect the intelligent tester or Techstream to the DLC3.

(b) Turn the ignition switch to ON and turn the intelligent tester or Techstream on.

(d) Enter the following menus: Powertrain / Engine / Data List / O2S (A/FS) Monitor.

(e) Check that the item O2S (A/FS) Monitor displays Incmpl (Incomplete).

(f) Start the engine and warm it up.

(g) Drive the vehicle at a vehicle speed of more than 10 km/h (6.2 mph) for 10 seconds or more.

(h) Allow the engine to idle for approximately 300 seconds or more.

(i) Note the state of the Data List items. Those items will change to Compl (Complete) as the O2 sensor monitor operates.

(j) Enter the following menus: Powertrain / Engine / DTC and check if any DTCs (any pending DTCs) are set.


Powertrain > Engine > Clear DTCs
50002 206
Powertrain > Engine > Data List
Tester Display
O2S(A/FS) Monitor CMPL
50003 206 19
Powertrain > Engine > Trouble Codes
50001 206
HINT:
·

The MIL is illuminated during step (h) if a malfunction still exists.

·

If the item O2S (A/FS) Monitor does not change to Compl (Complete), and any pending DTCs fail to set, extend the driving time.



NOTICE:

If the conditions in this test are not strictly followed, malfunctions may not be detected.


CAUTION / NOTICE / HINT

·

If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.

·

Read freeze frame data using the intelligent tester or Techstream. Freeze frame data record the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data, from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0133)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

e.

Read DTCs.

Result:
Result Proceed to
P0133 A
P0133 and other DTCs B


HINT:

If any DTCs other than P0133 are output, troubleshoot those DTCs first.




A

2.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)

B

2.READ VALUE USING INTELLIGENT TESTER OR TECHSTREAM (OUTPUT VOLTAGE OF HEATED OXYGEN SENSOR)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine / Data List / O2S B1S1.

Powertrain > Engine > Data List
Tester Display
O2S B1 S1
50003 206 37

e.

Warm up the engine.


f.

Warm up the heated oxygen sensor at an engine speed of 2,500 rpm for approximately 90 seconds.


g.

Read the voltage output of the front heated oxygen sensor displayed on the intelligent tester or Techstream, while the engine is idling.

Standard:

Fluctuates between less than 0.35 V and more than 0.45 V, and period "t" is less than 1.5 seconds (refer to table below).


A128469N02
1.552,0.458 1.958,0.75 0.406,0.292 10 1 V 1.542,1.479 1.896,1.781 0.354,0.302 10 0 V 2.542,1.396 2.833,1.615 0.292,0.219 10 t 2.771,1.396 3.115,1.656 0.344,0.26 10 t 2.583,0.26 3.031,0.542 0.448,0.281 10 OK 3.5,0.26 3.896,0.531 0.396,0.271 10 NG 4.406,0.26 4.865,0.583 0.458,0.323 10 NG 5.313,0.26 5.74,0.563 0.427,0.302 10 NG 1.375,1.177 1.979,1.552 0.604,0.375 10 0.35 V 1.365,0.781 1.948,1.042 0.583,0.26 10 0.45 V

Result:
Proceed to
OK
NG




OK

3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)

NG

9.PERFORM CONFIRMATION DRIVING PATTERN
3.INSPECT HEATED OXYGEN SENSOR (HEATER RESISTANCE)
a.

Inspect the heated oxygen sensor (sensor 1).

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>HEATED OXYGEN SENSOR(w/ Rear Heated Oxygen Sensor)>INSPECTION

Result:
Proceed to
OK
NG




OK

4.INSPECT VENTILATION HOSE

NG

4.INSPECT VENTILATION HOSE
a.

Check the ventilation hose connections.

Click hereEngine / Hybrid System>3SZ-VE EMISSION CONTROL>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

OK:

Ventilation hose is connected correctly, and is not damaged.


Result:
Proceed to
OK
NG




OK

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)

NG

REPAIR OR REPLACE VENTILATION HOSE

5.CHECK HARNESS AND CONNECTOR (HEATED OXYGEN SENSOR (SENSOR 1) - ECM)
a.

Disconnect the heated oxygen sensor (sensor 1) connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
For LHD
Tester Connections Condition Specified Conditions
C22-3 (+) - C24-11 (OX) Always Below 1 Ω
C22-1 (HTR-) - C24-3 (OXH1) Always Below 1 Ω
C22-4 (E) - C24-33 (E2) Always Below 1 Ω

For RHD
Tester Connections Condition Specified Conditions
C26-3 (+) - C24-11 (OX) Always Below 1 Ω
C26-1 (HTR-) - C24-3 (OXH1) Always Below 1 Ω
C26-4 (E) - C24-33 (E2) Always Below 1 Ω


Standard Resistance (Check for Short):
For LHD
Tester Connections Condition Specified Conditions
C22-3 (+) or C24-11 (OX) - Body ground Always 10 kΩ or higher
C22-1 (HTR-) or C24-3 (OXH1) - Body ground Always 10 kΩ or higher

For RHD
Tester Connections Condition Specified Conditions
C26-3 (+) or C24-11 (OX) - Body ground Always 10 kΩ or higher
C26-1 (HTR-) or C24-3 (OXH1) - Body ground Always 10 kΩ or higher



d.

Reconnect the heated oxygen sensor (sensor 1) connector.


e.

Reconnect the ECM connector.

Result:
Proceed to
OK
NG




OK

6.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK FUEL PRESSURE
a.

Check the fuel pressure.

Click hereEngine / Hybrid System>3SZ-VE FUEL>FUEL SYSTEM>ON-VEHICLE INSPECTION

Standard:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44.1 to 49.7 psi)


Result:
Proceed to
OK
NG




OK

7.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE FUEL SYSTEM

7.INSPECT FUEL INJECTOR (INJECTION AND VOLUME)
a.

Check the injector injection (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>3SZ-VE FUEL>FUEL INJECTOR>INSPECTION

Standard:

47 to 58 cm3 (2.9 to 3.5 cu in.) per 15 seconds


Result:
Proceed to
OK
NG




OK

8.CHECK SPARK AND IGNITION

NG

8.CHECK SPARK AND IGNITION
a.

Check the ignition system.

HINT:

Refer to Ignition System / On-Vehicle Inspection.

Click hereEngine / Hybrid System>3SZ-VE ENGINE CONTROL>IGNITION SYSTEM>ON-VEHICLE INSPECTION


OK:

Spark occurs.


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE IGNITION SYSTEM

9.PERFORM CONFIRMATION DRIVING PATTERN
HINT:

Clear all DTCs before performing the confirmation driving pattern.


Powertrain > Engine > Clear DTCs
50002 206
Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0133)
10.CHECK WHETHER DTC OUTPUT RECURS (DTC P0133)
a.

Connect the intelligent tester or Techstream to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the intelligent tester or Techstream on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 206

e.

Read DTCs.

Result:
Display (DTC Output) Proceed to
P0133 A
No output B




A

B