Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › 2011.11–2015.08
RM19Y0E _54 Brake _002992 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0015137 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C0210/23  RR wheel open wire/shorted  C0215/24  Left Rear Wheel Speed Sensor Signal  C1238/27  Foreign Object is Attached on Tip of Rear Speed Sensor RH  C1239/28  Foreign Object is Attached on Tip of Rear Speed Sensor LH  C1273/83  Low Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1274/84  Low Output Signal of Rear Speed Sensor LH (Test Mode DTC)  C1277/87  Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC)  C1278/88  Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC)  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (brake actuator assembly)U. These signals are used for the anti-lock brake system.

Speed sensor rotors have rows of alternating N and S magnetic poles, and their magnetic fields change when the rotors turn. Each speed sensor detects that magnetic field change and sends a pulse signal to the skid control ECU (brake actuator assembly). DTCs C1273/83,C1274/84,C1275/85 and C1275/85 are cleared when the speed sensor sends a vehicle speed signal or Test Mode ends. DTCs C1273/83,C1274/84,C1277/87 and C1278/88 are stored only in Test Mode.

C248682E02
1.771,0.667 2.344,0.667 false 1.646,1.365 2.167,1.365 2.167,1.365 2.167,1.594 false 4,0.323 5.74,0.813 1.74,0.49 10 Waveform (Reference): 0.354,1.26 1.875,1.76 1.521,0.5 10 Speed Sensor Rotor 0.844,0.563 2.01,0.99 1.167,0.427 10 Speed Sensor 3.979,0.75 7.083,1.26 3.104,0.51 10 Between Speed Sensor (-) and Body Ground 4.635,2.146 5.875,2.719 1.24,0.573 10 Low Speed 5.573,2.125 6.604,2.635 1.031,0.51 10 High Speed 6.594,1.292 7.104,1.667 0.51,0.375 10 1.4 V 6.594,1.635 7.146,1.979 0.552,0.344 10 0.7 V

DTC No. Detection Item DTC Detection Condition Trouble Area
C0210/23 RR wheel open wire/shorted
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor

·

Rear speed sensor circuit

·

Skid control sensor rotor

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C0215/24 Left Rear Wheel Speed Sensor Signal
1.

An open in the speed sensor signal circuit continues for 0.5 seconds or more.

2.

With the IG1 terminal voltage at 9.5 V or more, the sensor power supply voltage decreases for 0.5 seconds or more.


·

Rear speed sensor

·

Rear speed sensor circuit

·

Skid control sensor rotor

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1238/27 Foreign Object is Attached on Tip of Rear Speed Sensor RH
1.

The wheel deceleration rate is 51.2 G or more and no pulse signal is input 7 times.

2.

The vehicle speed is 10 km/h or higher and no pulse signal is output from the wheel speed sensor for more than 30 seconds.

3.

All of the following conditions are met.

1.

Vehicle speed is 10 km/h or higher.

2.

Stop light switch is off.

3.

Only one wheel speed sensor indicates 0 km/h.

4.

The difference in wheel speed between the other 3 wheels is less than 2 km/h for more than 0.35 second.


4.

With vehicle speed higher than 20 km/h and no pulse signal is output from the front wheel speed sensor for 20 seconds, and this condition has happened 8 trips in a row, and then has continued for more than 10 seconds.

5.

Wheel deceleration rate at 51.2 G or more is detected more than 75 times in 5 seconds.

6.

At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.

7.

Continuous ABS control for 45 seconds or more.


·

Rear speed sensor

·

Rear speed sensor circuit

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1239/28 Foreign Object is Attached on Tip of Rear Speed Sensor LH
1.

The wheel deceleration rate is 51.2 G or more and no pulse signal is input 7 times.

2.

The vehicle speed is 10 km/h or higher and no pulse signal is output from the wheel speed sensor for more than 30 seconds.

3.

All of the following conditions are met.

1.

Vehicle speed is 10 km/h or higher.

2.

Stop light switch is off.

3.

Only one wheel speed sensor indicates 0 km/h.

4.

The difference in wheel speed between the other 3 wheels is less than 2 km/h for more than 0.35 second.


4.

With vehicle speed higher than 20 km/h and no pulse signal is output from the front wheel speed sensor for 20 seconds, and this condition has happened 8 trips in a row, and then has continued for more than 10 seconds.

5.

Wheel deceleration rate at 51.2 G or more is detected more than 75 times in 5 seconds.

6.

At vehicle speed of 10 km/h (6 mph) or more, noise input once per rotor rotation for 15 seconds or more.

7.

Continuous ABS control for 45 seconds or more.


·

Rear speed sensor

·

Rear speed sensor circuit

·

Sensor installation

·

Skid control ECU (Brake actuator assembly)


C1273/83 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor

·

Sensor installation

·

Skid control sensor rotor

·

Skid control ECU (Brake actuator assembly)


C1274/84 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Rear speed sensor

·

Sensor installation

·

Skid control sensor rotor

·

Skid control ECU (Brake actuator assembly)


C1277/87 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) Detected only during Test Mode.
·

Skid control sensor rotor

·

Skid control ECU (Brake actuator assembly)


C1278/88 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) Detected only during Test Mode.
·

Skid control sensor rotor

·

Skid control ECU (Brake actuator assembly)



HINT:
·

DTCs C0210/23, C1238/28, C1273/83 and C1277/87 are for the rear speed sensor RH.

·

DTCs C0215/24, C1239/29, C1274/84 and C1278/88 are for the rear speed sensor LH.



WIRING DIAGRAM

C248681E04
5.333,0.865 5.719,1.24 0.385,0.375 10 17 5.583,0.938 6.188,1.292 0.604,0.354 10 RR1 5.333,1.177 5.76,1.552 0.427,0.375 10 16 2.333,0.865 2.646,1.177 0.313,0.313 10 1 2.333,1.167 2.667,1.469 0.333,0.302 10 2 2.333,1.771 2.688,2.146 0.354,0.375 10 1 2.333,2.083 2.656,2.417 0.323,0.333 10 2 5.583,1.25 6.271,1.594 0.688,0.344 10 RR0 2.156,0.948 2.448,1.188 0.292,0.24 10 + 2.177,1.24 2.458,1.573 0.281,0.333 10 - 2.156,1.865 2.438,2.115 0.281,0.25 10 + 2.177,2.156 2.448,2.448 0.271,0.292 10 - 5.406,1.781 5.781,2.104 0.375,0.323 10 5 5.583,1.854 6.063,2.188 0.479,0.333 10 RL1 5.406,2.083 5.792,2.448 0.385,0.365 10 4 5.583,2.167 6.156,2.531 0.573,0.365 10 RL0 4.99,2.458 5.479,2.75 0.49,0.292 10 B10 0.313,0.688 0.708,1.01 0.396,0.323 10 J7 4.99,2.625 6.927,3.51 1.938,0.885 10 SKID CONTROL ECU(BRAKE ACTUATOR ASSEMBLY) 0.302,0.854 1.292,1.74 0.99,0.885 10 REAR SPEED SENSOR LH 0.313,1.615 0.688,1.969 0.375,0.354 10 J2 0.302,1.771 1.302,2.813 1,1.042 10 REAR SPEED SENSOR RH

CAUTION / NOTICE / HINT

NOTICE:

If the brake actuator is replaced with a new one, the skid control ECU (brake actuator assembly) makes the shift to test mode automatically when the ignition switch is turned to ON for the first time. Be sure to complete the test mode checks (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (RR/RL WHEEL SPEED)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the intelligent tester on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC / Data List, and then drive the vehicle

Chassis > ABS/VSC/TRC > Data List
Tester Display
RR Wheel Speed
RL Wheel Speed
50003 509 47,48
Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
RR Wheel Speed Rear speed sensor RH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.
RL Wheel Speed Rear speed sensor LH reading Min.: 0 km/h (0 mph)
Max.: 326 km/h (202 mph)
Actual wheel speed No large fluctuations when driving at a constant speed.

f.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>OPERATION CHECK


OK:

The speed value output from the speed sensor displayed on the intelligent tester is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).


Result:
Proceed to
OK
NG




OK

2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
2.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Perform the sensor check in the Test Mode procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 509 3
OK:

All Test Mode DTCs are cleared.


Result:
Proceed to
OK
NG




OK

3.RECONFIRM DTC

NG

4.CHECK REAR SPEED SENSOR INSTALLATION
3.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509
Result:
Result Proceed to
DTC not output A
DTC output B


HINT:

If troubleshooting has been carried out according to the problem symptoms table, refer back to the table and proceed to the next step




A

B

8.REPLACE REAR SPEED SENSOR
4.CHECK REAR SPEED SENSOR INSTALLATION
a.
C108871C02
0.708,1.365 0.99,1.667 false 0.094,0.125 0.51,0.469 0.417,0.344 10 *1 1.031,1.625 1.448,1.969 0.417,0.344 10 *a 0.406,1.74 0.823,2.083 0.417,0.344 10 *b 2.729,1.823 3.146,2.167 0.417,0.344 10 *c
*1 Rear Speed Sensor
*a No clearance
*b CORRECT
*c INCORRECT


Turn the ignition switch off.


b.

Check the rear speed sensor installation.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>INSTALLATION

OK:

The installation bolt is tightened properly.

There is no clearance between the sensor and rear axle housing.


Result:
Proceed to
OK
NG




OK

5.INSPECT SPEED SENSOR TIP

NG

INSTALL REAR SPEED SENSOR CORRECTLY

5.INSPECT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

No scratches, oil or foreign matter on the sensor tip.


NOTICE:

Do not replace the speed sensor if no damage to the speed sensor tip is found.


HINT:
·

If the sensor is contaminated with oil or other foreign material, clean the sensor.

·

If there is iron powder sticking to the rotor, this will result in a malfunction. Confirm that the rotor is not contaminated with foreign material before replacing the sensor.



Result:
Proceed to
OK
NG




OK

6.INSPECT REAR SPEED SENSOR

NG

CLEAN OR REPLACE REAR SPEED SENSOR

6.INSPECT REAR SPEED SENSOR
a.

Turn the ignition switch off.



c.

Inspect the rear speed sensor.

Result:
Proceed to
OK
NG




OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)

NG

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR)
a.

Turn the ignition switch off.


b.

Disconnect the B10 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the J2*1 or J7*2 rear speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

*1: for RH

*2: for LH


Standard Resistance (Check for Open):
for LH
Tester Connection Condition Specified Condition
B10-5 (RL1) - J7-1 (+) Always Below 1 Ω
B10-4 (RL0) - J7-2 (-) Always Below 1 Ω

for RH
Tester Connection Condition Specified Condition
B10-17 (RR1) - J2-1 (+) Always Below 1 Ω
B10-16 (RR0) - J2-2 (-) Always Below 1 Ω


Standard Resistance (Check for Short):
for LH
Tester Connection Condition Specified Condition
B10-5 (+) - Body ground Always 10 kΩ or higher
B10-4 (-) - Body ground Always 10 kΩ or higher

for RH
Tester Connection Condition Specified Condition
B10-17 (RR1) - Body ground Always 10 kΩ or higher
B10-16 (RR0) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK
NG




OK

8.REPLACE REAR SPEED SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE REAR SPEED SENSOR
a.

Turn the ignition switch off.


b.

Replace the rear speed sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>REAR SPEED SENSOR>REMOVAL

Result:
Proceed to
NEXT




NEXT

9.RECONFIRM DTC
9.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509
Result:
Result Proceed to
DTC output A
DTC not output B




A

10.REPLACE SKID CONTROL SENSOR ROTOR

B

END

10.REPLACE SKID CONTROL SENSOR ROTOR
a.

Remove the skid control sensor rotor.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR AXLE SHAFT>REMOVAL


b.

Check the rear skid control sensor rotor.

OK:

No scratches, oil or foreign matter on the rotors.


Result:
Proceed to
NEXT




NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC
a.

Clear the DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 509

b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph).


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 509
Result:
Result Proceed to
DTC output A
DTC not output B




A

B

END