Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2015.08
RM19Y0E _57 Power Source / Network _003004 NETWORKING _0015181 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on the CAN Bus Check screen of the GTS or Techstream

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that correspond to "ECM Communication Stop Mode" in "DTC Combination Table" are output

Click here(Click here)


·

ECM main line or connector

·

Power source circuit of ECM

·

ECM ground circuit

·

ECM



WIRING DIAGRAM

C329960E03
2.167,5.354 2,5.354 2,5.354 1.833,4.438 false 3.385,1.625 3.219,1.625 3.219,1.625 2.823,2.927 false 0.115,4.521 1.385,5.208 1.271,0.688 10 false Combination Meter Assembly 0.469,3.906 1.031,4.24 0.563,0.333 10 false 120 Ω 4.292,3.854 4.854,4.188 0.563,0.333 10 false 120 Ω 1.635,1.771 2.198,2.104 0.563,0.333 10 false DLC3 1.313,0.25 3.375,0.698 2.063,0.448 10 false : CAN Main Bus Line (CANH) 1.344,0.563 3.406,1.01 2.063,0.448 10 false : CAN Main Bus Line (CANL) 1.344,0.917 3.406,1.365 2.063,0.448 10 false : CAN Branch Line (CANH) 1.344,1.26 3.406,1.708 2.063,0.448 10 false : CAN Branch Line (CANL) 4.927,5.177 6.01,5.583 1.083,0.406 10 false Trouble Area 2.24,5.281 4.365,5.719 2.125,0.438 10 false No. 1 CAN Junction Connector 3.479,1.542 4.854,2.292 1.375,0.75 10 false Main Body ECU (Fuse Block Assembly) 5.823,3.646 6.26,3.896 0.438,0.25 10 false EFI 5.906,2.583 6.615,3.49 0.708,0.906 10 false from No. 1 Integration Relay 5.177,2.458 5.427,2.719 0.25,0.26 10 false 1 5.104,2.656 5.5,2.979 0.396,0.323 10 false A24 5.104,3.083 5.5,3.406 0.396,0.323 10 false A24 5.104,3.51 5.5,3.833 0.396,0.323 10 false A24 5.104,3.917 5.5,4.24 0.396,0.323 10 false C50 3.719,3.729 4.115,4.052 0.396,0.323 10 false A24 3.708,3.094 4.104,3.417 0.396,0.323 10 false A24 3.771,2.906 4.021,3.167 0.25,0.26 10 false 25 5.188,2.896 5.438,3.156 0.25,0.26 10 false 2 5.146,3.323 5.396,3.583 0.25,0.26 10 false 13 5.188,3.74 5.438,4 0.25,0.26 10 false 4 4.375,4.625 4.885,4.885 0.51,0.26 10 false ECM 4.76,3.917 5.104,4.177 0.344,0.26 10 false E01 3.76,3.542 4.01,3.802 0.25,0.26 10 false 26 4.063,3.583 4.625,3.917 0.563,0.333 10 false LCAN 4.063,2.969 4.625,3.302 0.563,0.333 10 false HCAN 4.75,2.656 5.125,2.948 0.375,0.292 10 false +B1 4.75,3.073 5.125,3.365 0.375,0.292 10 false +B2 4.74,3.5 5.115,3.792 0.375,0.292 10 false BAT 5.104,4.344 5.5,4.667 0.396,0.323 10 false C50 5.177,4.177 5.427,4.438 0.25,0.26 9 false 5 4.76,4.333 5.104,4.594 0.344,0.26 10 false E02

CAUTION / NOTICE / HINT

NOTICE:
·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

·

DTC check procedure: Turn the ignition switch to ON, wait at least 6 seconds.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS LINES (ECM MAIN LINE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
A348485C07
1.5,0.25 1.917,0.5 0.417,0.25 0.969,0.958 0.969,0.125 0.969,0.125 1.135,0.125 true 0.844,0.948 0.844,0.365 0.844,0.365 0.677,0.365 true 0.094,0.104 0.385,0.385 0.292,0.281 10 false *a 1.583,0.292 2.01,0.563 0.427,0.271 10 false A24 0.281,0.292 0.781,0.542 0.5,0.25 10 false LCAN 1.198,0.052 1.698,0.302 0.5,0.25 10 false HCAN
*a Front view of wire harness connector
(to ECM)


Disconnect the A24 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A24-25 (HCAN) - A24-26 (LCAN) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK ECM POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE CAN MAIN LINES OR CONNECTOR (ECM)

2.CHECK ECM POWER SOURCE CIRCUIT

Result:
Result Proceed to
OK (for 1NR-VE) A
OK (for 2NR-VE) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)