Home › Engine / Hybrid System › 2NR-VE ENGINE CONTROL › SFI SYSTEM(w/o Air Fuel Ratio Sensor) › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042272 2NR-VE ENGINE CONTROL _0196163 SFI SYSTEM(w/o Air Fuel Ratio Sensor) C

2NR-VE ENGINE CONTROL  SFI SYSTEM(w/o Air Fuel Ratio Sensor)  P0171  Fuel System (Lean Faulty)  P0172  Fuel System (Rich Faulty)  


DESCRIPTION

The fuel trim is related to the feedback compensation value, not to the basic injection time. The fuel trim includes the short-term fuel trim and the long-term fuel trim.

The short-term fuel trim is the short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio. The signal from the oxygen sensor indicates whether the air-fuel ratio is rich or lean compared to the stoichiometric air-fuel ratio. This variance triggers a reduction in the fuel volume if the air-fuel ratio is rich, and an increase in the fuel volume if it is lean.

The short-term fuel trim varies from the central value due to individual engine differences, wear over time and changes in the operating environment. The long-term fuel trim, which controls the overall fuel compensation, adjusts for long-term deviations of the short-term fuel trim from the central value.

If both the short-term fuel trim and the long-term fuel trim are lean or rich beyond a certain value, the ECM determines this to be a malfunction, illuminates the MIL and sets a DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0171 Fuel System (Lean Faulty) When air-fuel ratio feedback stable after warming up engine, fuel trim considerably in error on lean side (2 trip detection logic).
·

Fuel injector blockage

·

Intake air flow meter assembly

·

Engine coolant temperature sensor

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in oxygen sensor circuit

·

Oxygen sensor

·

Ventilation hose

·

Running out of fuel

·

ECM


Comes on DTC stored
P0172 Fuel System (Rich Faulty) When air-fuel ratio feedback stable after warming up engine, fuel trim considerably in error on rich side (2 trip detection logic).
·

Injector leakage or blockage

·

Intake air flow meter assembly

·

Engine coolant temperature sensor

·

Ignition system

·

Fuel pressure

·

Gas leak from exhaust system

·

Open or short in oxygen sensor circuit

·

Oxygen sensor

·

ECM


Comes on DTC stored

HINT:
·

When DTC P0171 is recorded, the actual air-fuel ratio is on the lean side (Fuel trim corrected heavily on increase side). When DTC P0172 is recorded, the actual air-fuel ratio is on the rich side (Fuel trim corrected heavily on decrease side).

·

If the vehicle runs out of fuel, the air-fuel ratio is lean and DTC P0171 may be recorded. The MIL is then illuminated.

·

When the total of the short-term and long-term fuel trim values is within +48%, -40% (and ECT is more than 75°C (167°F)), the system is functioning normally.



CONFIRMATION DRIVING PATTERN

A288929E05
2.802,2.073 3.25,0.167 3.25,0.167 3.5,0.167 false 0.625,0.042 1.531,0.229 0.906,0.188 10 Vehicle Speed 1.031,0.354 1.646,0.552 0.615,0.198 10 100 km/h 1.104,1.229 1.719,1.427 0.615,0.198 10 60 km/h 1.292,2.021 1.771,2.229 0.479,0.208 10 Idling 0.49,2.271 1.656,2.448 1.167,0.177 10 Ignition Switch ON 2.031,2.344 2.646,2.542 0.615,0.198 10 [A] 3.573,0.083 6.365,0.26 2.792,0.177 10 Engine coolant temperature is 75°C or higher 3.271,1.875 3.885,2.073 0.615,0.198 10 [C] 2.521,1.875 3.135,2.073 0.615,0.198 10 [B] 4.823,0.479 5.438,0.677 0.615,0.198 10 [D] 2.146,3.115 3.26,3.302 1.115,0.188 10 Warming up 3.073,3.042 3.688,3.385 0.615,0.344 10 2 minutes or more 4.375,3.042 5.604,3.219 1.229,0.177 10 5 minutes or more 5.604,3.365 5.833,3.552 0.229,0.188 10 [E]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON and turn the GTS on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the GTS on [A].

6.

Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher with all the accessories switched off [B].

7.

With the engine warmed up, idle the engine for 2 minutes or more [C].

8.

Drive the vehicle at a speed between 60 and 100 km/h (37 and 62 mph) for 5 minutes or more [D].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Enter the following menus: Powertrain / EFI / Trouble Codes [E].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, the system is normal.




CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

A high oxygen sensor voltage (0.5 V or more) indicates a rich air-fuel ratio.

·

A low oxygen sensor voltage (0.4 V or less) indicates a lean air-fuel ratio.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read DTCs.

HINT:

If any DTCs other than P0171 or P0172 are output, troubleshoot those DTCs first.



Result:
Result Proceed to
DTC P0171 or P0172 is output A
DTC P0171 or P0172 and other DTCs are output B



A

2.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)

B

2.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature.


e.

Read the engine coolant temperature twice, when the engine is both cold and warmed up.

Standard:

With cold engine: Same as ambient air temperature.

With warm engine: 75°C to 100°C (167°F to 212°F).



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE, AIR FLOW RATE)

NG

3.READ VALUE USING GTS (ENGINE COOLANT TEMPERATURE, AIR FLOW RATE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Data List / Engine coolant temperature and Air flow rate.


e.

Allow the engine to idle until the engine coolant temperature reaches 80°C (176°F) or more.


f.

Read Air flow rate with the engine speed at 3000 rpm.

Standard:
GTS Display Condition Specified Condition
Air flow rate Shift lever position: Neutral
A/C: Off
Engine Speed: 3000 rpm
Between 3.0 and 8.0 g/s



Result:
Proceed to
OK
NG



OK

4.CHECK VENTILATION HOSE

NG

REPLACE INTAKE AIR FLOW METER ASSEMBLY

4.CHECK VENTILATION HOSE
a.

Check for ventilation hose connections.

OK:

Ventilation hose is connected correctly and is not damaged.



Result:
Proceed to
OK
NG



OK

5.CHECK SPARK AND IGNITION

NG

REPAIR OR REPLACE VENTILATION HOSE

5.CHECK SPARK AND IGNITION

Result:
Proceed to
OK
NG



OK

6.CHECK FOR EXHAUST GAS LEAK

NG

REPAIR OR REPLACE IGNITION SYSTEM

6.CHECK FOR EXHAUST GAS LEAK

Result:
Proceed to
OK
NG



OK

7.CHECK FUEL PRESSURE

NG

REPAIR OR REPLACE EXHAUST SYSTEM

7.CHECK FUEL PRESSURE

Result:
Proceed to
OK
NG



OK

8.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)

NG

REPAIR OR REPLACE FUEL SYSTEM

8.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
a.

Check the fuel injector assembly (whether fuel volume is high or low, and whether injection pattern is poor).

Click hereEngine / Hybrid System>2NR-VE FUEL>FUEL INJECTOR>INSPECTION


Result:
Proceed to
OK
NG



OK

9.READ VALUE USING GTS (O2S B1S1)

NG

REPLACE FUEL INJECTOR ASSEMBLY

9.READ VALUE USING GTS (O2S B1S1)
a.
A149559E09
0.375,1.073 0.792,1.417 0.417,0.344 10 false 1 V 0.396,2.604 0.885,2.99 0.49,0.385 10 false 0 V 2.875,2.677 3.427,3 0.552,0.323 10 false Time 0.073,0.229 2.25,0.604 2.177,0.375 10 false Oxygen Sensor Output 0.042,1.74 0.708,2.063 0.667,0.323 10 false 0.4 V 0.031,1.865 0.823,2.219 0.792,0.354 10 false or more

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Data List / O2S B1 S1.


e.

Warm up the engine.


f.

Allow the engine to run for 90 seconds at 2500 rpm.


g.

Read the output voltage of the oxygen sensor when the engine is idling and revving up.

OK:

Fluctuates with an amplitude of 0.4 V or more.



Result:
Proceed to
OK
NG



OK

10.PERFORM CONFIRMATION DRIVING PATTERN

NG

12.CHECK HARNESS AND CONNECTOR (OXYGEN SENSOR - ECM)
10.PERFORM CONFIRMATION DRIVING PATTERN
A286301E05
3.188,0.292 5.094,0.708 1.906,0.417 10 false 2 minutes or more 0.885,0.406 1.938,0.813 1.052,0.406 10 false Vehicle Speed 0.75,0.948 1.969,1.344 1.219,0.396 10 false 70 km/h (43 mph) 0.75,1.813 1.969,2.208 1.219,0.396 10 false Ignition Switch off 2.302,2.24 3.052,2.542 0.75,0.302 10 false Warm Up 4.875,1.958 5.625,2.26 0.75,0.302 10 false Time 2.469,1.531 2.927,1.729 0.458,0.198 10 false [d] 3.719,1.094 4.177,1.292 0.458,0.198 10 false [e] 4.948,1.542 5.406,1.74 0.458,0.198 10 false [f]

a.

Disconnect the negative battery cable for more than 1 minute to clear the air-fuel ratio learning value.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up [d].


f.

Drive the vehicle at a vehicle speed of 70 km/h (43 mph) for 2 minutes or more [e].


g.

Turn the ignition switch off [f].


h.

Repeat steps [d] and [e], in order to set DTCs (using 2 trip detection logic).

HINT:

The MIL is illuminated during step [e] if a malfunction still exists.


NOTICE:

If the conditions in this test are not strictly followed, malfunctions may not be detected.



Result:
Proceed to
NEXT



NEXT

11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
11.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read DTCs.


Result:
Result Proceed to
DTC P0171 or P0172 is output A
DTC is not output B



A

12.CHECK HARNESS AND CONNECTOR (OXYGEN SENSOR - ECM)

B

16.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
12.CHECK HARNESS AND CONNECTOR (OXYGEN SENSOR - ECM)
a.

Disconnect the oxygen sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connections Condition Specified Conditions
C22-3 (+) - C50-30 (OX) Always Below 1 Ω
C22-4 (E) - C50-51 (OX-) Always Below 1 Ω
C22-3 (+) or C50-30 (OX) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE OXYGEN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE OXYGEN SENSOR

Result:
Proceed to
NEXT



NEXT

14.PERFORM CONFIRMATION DRIVING PATTERN
14.PERFORM CONFIRMATION DRIVING PATTERN
A286301E05
3.188,0.292 5.094,0.708 1.906,0.417 10 false 2 minutes or more 0.885,0.406 1.938,0.813 1.052,0.406 10 false Vehicle Speed 0.75,0.948 1.969,1.344 1.219,0.396 10 false 70 km/h (43 mph) 0.75,1.813 1.969,2.208 1.219,0.396 10 false Ignition Switch off 2.302,2.24 3.052,2.542 0.75,0.302 10 false Warm Up 4.875,1.958 5.625,2.26 0.75,0.302 10 false Time 2.469,1.531 2.927,1.729 0.458,0.198 10 false [d] 3.719,1.094 4.177,1.292 0.458,0.198 10 false [e] 4.948,1.542 5.406,1.74 0.458,0.198 10 false [f]

a.

Disconnect the negative battery cable for more than 1 minute to clear the air-fuel ratio learning value.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Start the engine and warm it up [d].


f.

Drive the vehicle at a vehicle speed of 70 km/h (43 mph) for 2 minutes or more [e].


g.

Turn the ignition switch off [f].


h.

Repeat steps [d] and [f], in order to set DTCs (using 2 trip detection logic).

NOTICE:

If the conditions in this test are not strictly followed, malfunctions may not be detected.


HINT:

The MIL is illuminated during step [e] if a malfunction still exists.



Result:
Proceed to
NEXT



NEXT

15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / EFI / Trouble Codes.


e.

Read DTCs.


Result:
Result Proceed to
DTC is not output A
DTC P0171 or P0172 is output B



A

16.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST

B

16.CONFIRM IF VEHICLE HAS RUN OUT OF FUEL IN PAST
Result:
Result Proceed to
Vehicle has run out of fuel in past A
Vehicle has not run out of fuel in past B



A

DTC CAUSED BY RUNNING OUT OF FUEL

B