Home › Engine / Hybrid System › 1NR-VE ENGINE MECHANICAL › ENGINE ASSEMBLY › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042273 1NR-VE ENGINE MECHANICAL _0196183 ENGINE ASSEMBLY A

1NR-VE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transmission is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 1. DISCHARGE FUEL SYSTEM PRESSURE

Hide 2.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 4.REMOVE FRONT WHEELS

Hide 51441 5.REMOVE NO. 1 ENGINE UNDER COVER

a.
A361364C01
3.333,2.167 3.417,2.167 false
V100135

Bolt
V100136

Clip


Remove the 8 bolts, clip and No. 1 engine under cover.


Hide 7.DRAIN MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 8.DRAIN AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 17750A 9.REMOVE AIR CLEANER INLET ASSEMBLY

A360030

a.

Remove the bolt and disconnect the earth cable.


b.
A360031

Loosen the hose clamp and remove the 2 bolts and air cleaner inlet assembly.


Hide 10.REMOVE BATTERY

a.
A360091

Loosen the nut, and separate the positive (+) battery terminal.


b.

Remove the bolt and loosen the nut.


c.

Disconnect the harness clamp and remove the battery hold down clamp sub-assembly.


d.

Remove the battery cover.


e.

Remove the battery.


Hide 74411 11.REMOVE BATTERY CARRIER

a.
A360092

Remove the 4 bolts and battery carrier.


Hide 17775A 12.REMOVE NO. 3 AIR CLEANER PIPE BRACKET

a.
A360093

Remove the bolt and No. 3 air cleaner pipe bracket.


Hide 16361A 13.REMOVE FAN AND GENERATOR V BELT

Hide 16571C 14.REMOVE NO. 1 RADIATOR HOSE

Hide 25860 15.REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

Hide 77754 16.DISCONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE

a.
A364926

for LHD:

i.

Disengage the 2 guides and disconnect the No. 1 charcoal canister outlet hose from the air cleaner cap sub-assembly.



b.
A364924

for RHD:

i.

Disengage the clamp and disconnect the No. 1 charcoal canister outlet hose from the charcoal canister outlet guide.



Hide 17705 17.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

a.
A360094C01
0.615,0.448 0.938,0.76 true 1.51,0.938 1.802,0.292 true 2.667,0.552 2.917,0.323 true 1.833,0.104 2.146,0.26 0.313,0.156 10 true *1 0.469,0.281 0.781,0.438 0.313,0.156 10 true *2 2.958,0.146 3.271,0.302 0.313,0.156 10 true *3
*1 Intake Air Flow Meter Assembly
*2 No. 1 Air Cleaner Hose
*3 No. 2 Ventilation Hose


Disconnect the harness clamp from the air cleaner cap sub-assembly.


b.

Disconnect the harness clamp and connector from the intake air flow meter assembly.


c.

Loosen the hose clamp and disconnect the No. 1 air cleaner hose.


d.

Disengage the guide and disconnect the No. 2 ventilation hose from the air cleaner cap sub-assembly.


e.

Unlock the 2 clamps and remove the air cleaner cap sub-assembly.


Hide 17801 18.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner filter element sub-assembly.


Hide 19.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

a.
A361365

Remove the 2 bolts and air cleaner case sub-assembly.


Hide 17881 20.REMOVE NO. 1 AIR CLEANER HOSE

Hide 44730A 21.REMOVE NO. 1 VACUUM HOSE (for LHD)

a.
A364916

Loosen the 2 clips and remove the No. 1 vacuum hose.


Hide 44730A 22.DISCONNECT NO. 1 VACUUM HOSE (for RHD)

Hide 88320 23.SEPARATE COOLER COMPRESSOR ASSEMBLY (w/ Air Conditioning System)

a.
A360095

Disconnect the connector.


b.

Remove the 4 bolts and separate the cooler compressor assembly.

HINT:
A360096

It is not necessary to completely remove the cooler compressor assembly. With the hoses connected to the cooler compressor assembly, hang the cooler compressor assembly on the vehicle body with a rope.



Hide 82661 24.REMOVE NO. 1 RELAY BLOCK COVER

Hide 25.DISCONNECT ENGINE WIRE

a.
A360097

Pull up the lever to disconnect the ECM connector.


b.
A360098

Disconnect the 4 connectors.


c.

Disengage the 2 claws and disconnect the engine wire from the engine room relay block.


d.
A360099

Remove the bolt and disconnect the engine wire from the body.


e.
A360100

Engage the 2 harness clamps and disconnect the engine wire.


Hide 87245X 26.DISCONNECT HEATER WATER HOSE (w/ Heater)

Hide 87246X 27.DISCONNECT NO. 2 HEATER WATER HOSE (w/ Heater)

Hide 45220 28.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 37110 29.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 33820B 30.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transmission)

Hide 33820B 31.SEPARATE TRANSMISSION CONTROL CABLE ASSEMBLY (for Automatic Transmission)

Hide 31340 32.SEPARATE CLUTCH RELEASE CABLE ASSEMBLY (for Manual Transmission)

a.
C150623

Remove the clutch housing cover from the clutch housing.


b.
C341450C02
2.646,1.26 2.927,1.521 true 2.99,1.49 3.24,1.688 0.25,0.198 10 false *1
*1 Adjusting Nut


Disconnect the clutch release cable assembly from the clutch release fork.

HINT:
·

If necessary, loosen the adjusting nut in advance.

·

Pushing the clutch release fork toward the front of the vehicle will make it easier to remove the clutch release cable assembly.




c.
C341451

Remove the 2 bolts and disconnect the clutch release cable assembly from the clutch housing.


Hide 17410 33.DISCONNECT FRONT EXHAUST PIPE ASSEMBLY

Hide 58151A 34.REMOVE NO. 1 FLOOR HEAT INSULATOR

Hide 17410 35.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 17451 36.REMOVE EXHAUST PIPE GASKET

Hide 23841B 37.REMOVE EFI FUEL PIPE CLAMP

a.

Remove the EFI fuel pipe clamp.


Hide 23901 38.DISCONNECT FUEL TUBE SUB-ASSEMBLY

A360101C01
0,0 0,0 false
V100135

Pinch
V100136

Pull


a.

Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel tank to canister tube sub-assembly.

NOTICE:

Make sure to read the disconnecting the fuel tube connector notice before proceeding with work.



Hide 16572D 39.REMOVE NO. 2 RADIATOR HOSE

a.
A361295

Loosen the 2 hose clamps and remove the No. 2 radiator hose.


Hide 32921D 40.REMOVE OIL COOLER INLET HOSE (for Automatic Transmission)

Hide 32922A 41.REMOVE OIL COOLER OUTLET HOSE (for Automatic Transmission)

Hide 48810 42.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 43.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 44.REMOVE FRONT STABILIZER BRACKET

Hide 45.DISCONNECT FRONT LOWER SUSPENSION ARM

·

Use the same procedure for the RH side as for the LH side.

·

The procedure listed below is for the LH side.


a.

Remove the clip and nut.


b.
C245934C04
0.76,1.521 0.615,1.521 0.615,1.521 0.615,1.917 false 0.74,1.583 0.615,1.583 false 2.135,1.385 1.99,1.385 1.99,1.385 1.99,1.958 false 2.135,1.552 1.99,1.552 false 0.438,1.927 1.219,2.177 0.781,0.25 10 SST 1.813,1.958 2.781,2.177 0.969,0.219 10 SST 2.917,1.198 3.292,1.656 0.375,0.458 10 *a
*a 1 mm (0.04 in.)


Install SST to the front lower suspension arm ball joint as shown in the illustration.

SST
09960-20010  (09961-02050)

NOTICE:

Check that the clearance measurement between SST and the steering knuckle is 1 mm (0.04 in.).



c.

Using SST, remove the front lower suspension arm ball joint from the steering knuckle as shown in the illustration.

SST
09960-20010  (09961-02050)

C245933C04
3.479,2.5 3.479,2.885 false 0.563,2.021 1.063,2.427 0.5,0.406 10 false A 0.563,1.719 1.063,2.135 0.5,0.417 10 false B 6.042,0.479 6.458,0.885 0.417,0.406 10 false *2 4.365,2.021 4.833,2.438 0.469,0.417 10 false *3 5.51,2.625 5.948,2.958 0.438,0.333 10 false *1 3.354,2.906 4.031,3.292 0.677,0.385 10 false SST 5.542,2.99 5.979,3.323 0.438,0.333 10 false *1
*1 Apply grease *2 Place the wrench here
*3 Turn - -


NOTICE:

Apply grease to the threads and end of the SST bolt.


HINT:
·

Install SST so that A and B are parallel.

·

Be sure to place a wrench on the part indicated in the illustration.

·

Do not damage the front lower suspension arm ball joint dust cover.




Hide 45047 46.SEPARATE TIE ROD END SUB-ASSEMBLY LH

Hide 45046 47.SEPARATE TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48.REMOVE ENGINE AND TRANSMISSION ASSEMBLY

a.

for Manual Transmission:

i.
A361297C01
3.333,3.417 3.417,3.417 false
V100155

Attachment Placement Position


Place height adjustments or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with transmission.

NOTICE:
·

Place the height adjustments or plate lift attachments so that the engine assembly with transmission is level.

·

Securely support the engine assembly with transmission to prevent it from turning upside down until it is secured to the engine lifter.

·

To prevent deformation of the oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the engine assembly.

·

Do not position the height adjustment attachments or plate lift attachments under the front lower suspension crossmember sub-assembly.





b.

for Automatic Transmission:

i.
A361296C01
0,0 0,0 false
V100155

Attachment Placement Position


Place height adjustments or plate lift attachments in the positions shown in the illustration and set an engine lifter underneath the engine assembly with transmission.

NOTICE:
·

Place the height adjustments or plate lift attachments so that the engine assembly with transmission is level.

·

Securely support the engine assembly with transmission to prevent it from turning upside down until it is secured to the engine lifter.

·

To prevent deformation of the oil pan sub-assembly, never set any attachments against the oil pan sub-assembly of the engine assembly.

·

To prevent deformation of the transmission oil pan sub-assembly, never set any attachments against the transmission oil pan sub-assembly.

·

Do not position the height adjustment attachments or plate lift attachments under the front lower suspension crossmember sub-assembly.





c.
A361298

Remove the 6 bolts and the rear engine support member sub-assembly.


d.
A361299

Remove the 6 bolts and the front lower suspension crossmember sub-assembly.


e.
A361300

Remove the 4 bolts, operate the engine lifter and slowly remove the engine assembly with transmission from the vehicle.

NOTICE:

When removing the engine assembly with transmission, be careful not to damage any wire harnesses.



f.

Using a rope or belt, secure the engine assembly with transmission to the engine lifter.

NOTICE:
·

Set the engine assembly with transmission so that it is horizontal.

·

Do not tighten the rope or belt with a tightening mechanism more than necessary.




Hide 50.REMOVE ENGINE WIRE

a.
A361301

Remove the 2 bolts and disconnect engine wire.


b.

Disconnect all of the clamps and connectors and remove the engine wire from the engine assembly.


Hide 16591A 52.DISCONNECT RADIATOR PIPE RADIATOR HOSE

Hide 87245X 53.REMOVE HEATER WATER HOSE (w/ Heater)

A363885

a.

Loosen the clip and remove the heater water hose.


Hide 87246X 54.REMOVE NO. 2 HEATER WATER HOSE (w/ Heater)

a.
A363886

Loosen the clip and remove the No. 2 heater water hose.


Hide 16283 55.REMOVE NO. 6 WATER BY-PASS HOSE (w/o Heater)

a.
A361377

Loosen 2 clips and remove the No. 6 water by-pass hose.


Hide 16507 56.REMOVE RADIATOR PIPE SUB-ASSEMBLY

Hide 25051 57.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

Hide 58.INSTALL ENGINE HANGER

a.
A361302C01
1.948,0.031 2.219,0.198 0.271,0.167 10 false *b 0.042,0.042 0.313,0.208 0.271,0.167 10 true *a
*a Intake Side
*b Exhaust Side


Install the 2 engine hangers with the 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
Part Name Part No.
No. 1 Engine Hanger (Black) 12281-0Y070
No. 1 Engine Hanger (Silver) 12281-0Y010
No. 2 Engine Hanger (Black) 12282-BZ140
No. 2 Engine Hanger (Silver) 12282-BZ150
Bolt 90105-T0125



b.

Attach the sling device to the engine hangers and chain block.

NOTICE:

Make sure that the sling angle is correct to prevent the engine assembly with transmission and engine hangers from being damaged or deformed.



Hide 28100 59.REMOVE STARTER ASSEMBLY (for Manual Transmission)

Hide 28100 60.REMOVE STARTER ASSEMBLY (for Automatic Transmission)

Hide 61.REMOVE MANUAL TRANSMISSION ASSEMBLY (for Manual Transmission)

Hide 62.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 12361 63.REMOVE FRONT ENGINE MOUNTING INSULATOR

a.
A361305C01
0.167,0.031 0.479,0.188 0.313,0.156 10 false *a 0.219,1.906 0.531,2.063 0.313,0.156 10 false *b
*a LH Side
*b RH Side
V100135

Bolt
V100136

Nut


Remove the 4 bolts and 2 nuts, shown in the illustration, then remove the 2 front engine mounting insulators.


Hide 51201 64.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Operate the engine sling device and chain block, then remove the front suspension crossmember sub-assembly.


b.

Using a rope or belt, secure the engine assembly to the engine lifter.

NOTICE:
·

Set the engine assembly so that it is horizontal.

·

Do not tighten the rope or belt with a tightening mechanism more than necessary.




Hide 12311 65.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

A363037

a.

Remove the 3 bolts and front No. 1 engine mounting bracket RH.


Hide 12315 66.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET LH

A363038

a.

Remove the 4 bolts and front No. 1 engine mounting bracket LH.


Hide 31210 67.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31250 68.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 13405 69.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transmission)

Hide 32101 70.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for Automatic Transmission)

Hide 71.INSTALL ENGINE STAND

a.

Using a sling device and chain block, install the engine assembly onto the engine stand.

NOTICE:
·

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.

·

Securely support the engine assembly to prevent it from turning upside down until it is secured to an engine stand.