Home › Engine / Hybrid System › 1NR-VE ENGINE MECHANICAL › ENGINE UNIT › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042273 1NR-VE ENGINE MECHANICAL _0196184 ENGINE UNIT A

1NR-VE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 12108A 2.REMOVE OIL FILLER CAP GASKET

a.
A128159

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 11101J 3.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 12204 7.REMOVE VENTILATION VALVE SUB-ASSEMBLY

Hide 12204A 8.REMOVE VENTILATION SYSTEM GROMMET

Hide 89422A 10.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 11201 11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A361325C01
0.823,1.583 0.354,0.865 0.354,0.865 0.833,0.729 true 0.146,0.74 0.344,0.927 0.198,0.188 10 true *1
*1 Seal Washer and Plate Washer


Remove the 17 bolts, 2 seal washers, 2 plate washers and cylinder head cover sub-assembly.


Hide 11213 12.REMOVE CYLINDER HEAD COVER GASKET

Hide 11159H 13.REMOVE CAMSHAFT BEARING CAP OIL HOLE GASKET

Hide 83530 14.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89615 15.REMOVE KNOCK CONTROL SENSOR

Hide 15601 16.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 16031 17.REMOVE WATER INLET SUB-ASSEMBLY WITH THERMOSTAT

Hide 16326 18.REMOVE NO. 2 WATER INLET HOUSING GASKET

Hide 20.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Turn the crankshaft until its groove and the groove of the timing chain cover sub-assembly are aligned.

A362990C01
1.115,2.177 1.375,1.677 1.375,1.677 1.177,2.229 true 3.125,0.469 2.354,0.656 2.354,0.656 3.104,0.615 true 4.208,0.5 4.917,0.521 true 6.438,1.875 6.698,1.781 6.698,1.781 6.375,2 true 2.177,0.573 2.49,0.729 0.313,0.156 10 false *a 1.396,1.531 1.708,1.688 0.313,0.156 10 false *b 4.948,0.438 5.26,0.594 0.313,0.156 10 false *a 4.167,0.115 4.479,0.313 0.313,0.198 10 false 1° 3.073,0.094 3.385,0.292 0.313,0.198 10 false 1° 6.76,1.688 7.073,1.844 0.313,0.156 10 false *b
*a Timing Mark *b Groove


NOTICE:

Never turn the crankshaft pulley counterclockwise (when viewed from the front of the engine).



b.

Check that each timing mark of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are positioned as shown in the illustration. If not, turn the crankshaft 1 revolution (360°) to align the timing marks as shown in the illustration.


Hide 11302 22.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11302A 23.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 13540 24.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 13562 25.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13591 26.REMOVE TIMING CHAIN TENSION ARM

Hide 13506 27.REMOVE CHAIN SUB-ASSEMBLY

Hide 13566B 28.REMOVE TIMING CHAIN GUIDE

Hide 13521 29.REMOVE CRANKSHAFT TIMING GEAR OR SPROCKET

a.

Remove the crankshaft timing gear or sprocket from the crankshaft.


Hide 13050 30.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.

Check the lock of the camshaft timing gear assembly.


b.

Release the lock pin.

NOTICE:

Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.


i.
A198701C13
1.615,0.115 1.167,0.396 true 0.646,2.698 1.063,1.646 true 1.708,0.75 0.844,0.521 true 1.646,0.042 1.844,0.24 0.198,0.198 10 *a 0.542,2.719 0.74,2.917 0.198,0.198 10 *c 1.75,0.698 1.948,0.896 0.198,0.198 10 *b
*a Adhesive Tape Sealing Area
*b Prick a Hole
*c Adhesive Tape


Clean the VVT oil hole on the intake side of the camshaft bearing cap, and completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to seal the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



ii.

Prick a hole in the adhesive tape sealing the oil hole as shown in the illustration. (Procedure A)


iii.
A198702

Apply approximately 150 kPa (1.5 kgf/cm2, 22 psi) of air pressure to the hole pricked in procedure A to release the lock pin.

NOTICE:
·

If air leaks out, reattach adhesive tape.

·

Cover the oil hole with a piece of cloth when applying air pressure to prevent oil from spraying.

·

Do not lock the camshaft timing gear assembly. If it is locked, release the lock pin again.



HINT:
·

The camshaft timing gear assembly may be turned in the advance direction without applying any force.

·

If enough air pressure cannot be applied because of air leakage from the port, releasing the lock pin may be difficult.




iv.

Remove the adhesive tape from the camshaft bearing cap.



c.
A197613C12
1.156,1.635 1.958,1.813 1.958,1.813 1.125,1.031 true 0.948,1.281 1.927,1.802 1.927,1.802 1.344,1.438 true 2,1.75 2.313,1.948 0.313,0.198 10 *a
*a Do not Remove


Remove the bolt while holding the hexagonal portion of the camshaft, then remove the camshaft timing gear assembly.

NOTICE:
·

Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.

·

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.




Hide 13070A 31.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A197612C12
0.854,1.198 1.927,1.51 1.927,1.51 1.281,1.458 true 1.115,1.552 1.938,1.51 1.938,1.51 1.094,0.875 true 1.969,1.427 2.281,1.719 0.313,0.292 10 *a
*a Do not Remove


Remove the bolt while holding the hexagonal portion of the No. 2 camshaft, then remove the camshaft timing exhaust gear assembly.

NOTICE:
·

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing exhaust gear assembly horizontal while removing it from the No. 2 camshaft.




Hide 32.REMOVE CAMSHAFT BEARING CAP

Hide 15678A 33.REMOVE OIL CONTROL VALVE FILTER

a.
A325183

Remove the oil control valve filter from the No. 1 camshaft bearing cap.


Hide 13512 34.REMOVE NO. 2 CAMSHAFT

Hide 13801 36.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A197616

Remove the 16 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 37.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A197617

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 11103 38.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 11101 39.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11445 41.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A362991

Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.


Hide 42.REMOVE OIL PAN DRAIN PLUG

a.
A362992

Remove the oil pan drain plug and gasket from the oil pan sub-assembly.


Hide 12101 43.REMOVE OIL PAN SUB-ASSEMBLY

a.
A362993

Uniformly loosen and remove the 10 bolts.


b.
A362994C01
0.833,0.583 1.771,1.396 1.771,1.396 2.323,1.083 true 0.813,3.656 1.51,3.656 true 1.708,1.458 2.021,1.615 0.313,0.156 10 false *a 1.563,3.594 1.875,3.75 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the oil pan sub-assembly and cylinder block sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A362995

Remove the gasket from the cylinder block sub-assembly.


Hide 12121 44.REMOVE NO. 1 OIL PAN BAFFLE PLATE

a.
A362996

Remove the 4 bolts and No. 1 oil pan baffle plate from the oil pan sub-assembly.


Hide 12122 45.REMOVE NO. 2 OIL PAN BAFFLE PLATE

a.
A362997

Remove the 2 bolts and No. 2 oil pan baffle plate from the oil pan sub-assembly.


Hide 15104 46.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A362998

Remove the 2 bolts and oil strainer sub-assembly from the oil pan sub-assembly.


Hide 47.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


a.
A294131

Remove the 10 ring pins from the camshaft housing sub-assembly.


Hide 48.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


a.
A362999

Remove the 2 straight pins from the oil pan sub-assembly.