Home › Engine / Hybrid System › 1NR-VE LUBRICATION › OIL PUMP › from 2015.08
RM19Y0E _51 Engine / Hybrid System _042283 1NR-VE LUBRICATION _0196246 OIL PUMP A

1NR-VE LUBRICATION  OIL PUMP  REMOVAL  


PROCEDURE

Hide 1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 51441 2.REMOVE NO. 1 ENGINE UNDER COVER

Hide 17750A 5.REMOVE AIR CLEANER INLET ASSEMBLY

Hide 17700 6.REMOVE AIR CLEANER ASSEMBLY

Hide 7.REMOVE EARTH CABLE

A361322

a.

Remove the bolt and earth cable.


Hide 8.DISCONNECT ENGINE WIRE

A361323

a.

Remove the 2 bolts and disconnect the engine wire from the timing chain cover sub-assembly.


Hide 27020 9.REMOVE GENERATOR ASSEMBLY

Hide 16571C 10.REMOVE NO. 1 RADIATOR HOSE

Hide 12262 13.REMOVE NO. 2 VENTILATION HOSE

Hide 12261 14.DISCONNECT VENTILATION HOSE

Hide 77754 15.DISCONNECT NO. 1 CHARCOAL CANISTER OUTLET HOSE (for RHD)

Hide 11201 16.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

A361324

a.

Disconnect the oxygen sensor connector and 2 camshaft oil control valve assembly connectors.


b.

Disconnect the 5 harness clamps and engine wire.


c.
A361325C01
0.823,1.583 0.354,0.865 0.354,0.865 0.833,0.729 true 0.146,0.74 0.344,0.927 0.198,0.188 10 true *1
*1 Seal Washer and Plate Washer


Remove the 17 bolts, 2 seal washers, 2 plate washers and cylinder head cover sub-assembly.


Hide 11213 17.REMOVE CYLINDER HEAD COVER GASKET

A361336

a.

Remove the cylinder head cover gasket.


Hide 11159H 18.REMOVE CAMSHAFT BEARING CAP OIL HOLE GASKET

A361331

a.

Remove the 2 camshaft bearing cap oil hole gaskets from the camshaft bearing caps.

NOTICE:

If any camshaft bearing cap oil hole gasket is missing, check that no camshaft bearing cap oil hole gaskets are stuck to the cylinder head cover sub-assembly.



Hide 16603 19.REMOVE NO. 1 IDLER PULLY SUB-ASSEMBLY (w/ Air Conditioning System)

Hide 16620 20.REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

Hide 16281 23.DISCONNECT NO. 4 WATER BY-PASS HOSE

Hide 16572D 24.DISCONNECT NO. 2 RADIATOR HOSE

Hide 16031 25.REMOVE WATER INLET SUB-ASSEMBLY WITH THERMOSTAT

Hide 16326 26.REMOVE NO. 2 WATER INLET HOUSING GASKET

Hide 11302 27.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

a.
A361327C01
1.573,1.573 1.75,1.781 false 1.417,1.427 1.729,1.625 0.313,0.198 10 true *1
*1 Gasket


Remove the 27 bolts and the gasket.


b.
A361337C01
0.198,1.083 0.385,0.719 true 0.5,2.854 0.771,2.385 true 1.01,4.49 0.448,4.25 true 2.865,3.49 3.115,2.896 true 2.938,0.958 3.125,1.365 true 0.073,1.104 0.385,1.26 0.313,0.156 10 false *a 0.344,2.854 0.656,3.01 0.313,0.156 10 false *a 1.083,4.427 1.281,4.573 0.198,0.146 10 true *a 3.125,2.76 3.323,2.906 0.198,0.146 10 true *a 3.177,1.354 3.375,1.5 0.198,0.146 10 true *a
*a Protective Tape


Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly, cylinder head sub-assembly and cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the timing chain cover sub-assembly, cylinder block sub-assembly, and cylinder head sub-assembly.


HINT:

Tape the screwdriver tip before use.



c.
A361338

Remove the 3 O-rings.


d.
A361339

Using an 8 mm socket hexagon wrench, remove the plug.


Hide 11302A 28.REMOVE TIMING CHAIN COVER OIL SEAL

a.
A361340C01
0.958,0.385 1.5,0.865 true 1.917,1.063 2.5,1.448 true 0.781,0.229 1.094,0.385 0.313,0.156 10 false *a 2.563,1.438 2.875,1.594 0.313,0.156 10 false *b
*a Protective Tape
*b Wooden Block


Using a screwdriver with its tip wrapped in protective tape and wooden block, remove the timing chain cover oil seal.