Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT › 2016.10–2019.09
RM32K0E _58 Vehicle Interior _061609 HEATING / AIR CONDITIONING _0300402 AIR CONDITIONING UNIT A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during air conditioning unit removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Lane departure alert system (w/ Steering Control) (Click here)
Simple intelligent parking assist system*1
Toyota parking assist-sensor system*1
Pre-collision system
Initialize back door lock Power door lock control system (Click here)
·

No. 1 air conditioning radiator damper servo sub-assembly

·

Air conditioning amplifier assembly


Initialize servo motor (Air conditioning system) DTCs are stored (Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>SIMPLE INTELLIGENT PARKING ASSIST SYSTEM>CALIBRATION

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for the LHD vehicles.



PROCEDURE

Hide 3.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 4.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55735A 5.REMOVE WATER GUARD PLATE LH

Hide 55736D 6.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 7.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 8.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 9.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 87246 10.DISCONNECT OUTLET HEATER WATER HOSE

a.
I112448

Slide the hose clip to disconnect the outlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the outlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the outlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245 11.DISCONNECT INLET HEATER WATER HOSE

a.
I112449

Slide the hose clip to disconnect the inlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the inlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the inlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 88707 12.DISCONNECT SUCTION PIPE SUB-ASSEMBLY

a.
I112450

Remove the bolt and rotate the hook connector as shown in the illustration.


b.
I112451

Disconnect the suction pipe sub-assembly.


c.

Remove the O-ring from the suction pipe subassembly.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 88716A 13.DISCONNECT COOLER REFRIGERANT LIQUID PIPE A

a.
I112452

Disconnect the cooler refrigerant liquid pipe A.


b.

Remove the O-ring from the cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 14.REMOVE FRONT SEAT ASSEMBLY LH

Hide 15.INSTALL FRONT SEAT ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 55401E 16.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 17.REMOVE STEERING COLUMN ASSEMBLY

Hide 85940 18.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY

Hide 89340A 19.REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)

Hide 82877 20.REMOVE ECU INTEGRATION BOX RH (for LHD)

Hide 82878 21.REMOVE ECU INTEGRATION BOX LH (for RHD)

Hide 88625Q 22.REMOVE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

a.
I112333

Disconnect the connector and aspirator to remove the cooler thermistor (room temperature sensor).


Hide 55215D 23.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
I112338

Remove the 2 front floor carpet clips.


b.
I112339C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.


d.
I112343

Disengage the clips to remove the No. 3 dash panel insulator pad.


Hide 87212K 24.REMOVE REAR NO. 6 AIR DUCT (w/ Rear Air Duct)

a.
I112340C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 6 air duct as shown in the illustration.


Hide 87212J 25.REMOVE REAR NO. 5 AIR DUCT (w/ Rear Air Duct)

a.
I112341C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 5 air duct as shown in the illustration.


Hide 87212H 26.REMOVE REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

a.
I112334

Remove the 2 front floor carpet clips.


b.
I112335C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.


d.
I112336C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 4 air duct as shown in the illustration.


Hide 87212G 27.REMOVE REAR NO. 3 AIR DUCT (w/ Rear Air Duct)

a.
I112337C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 3 air duct as shown in the illustration.


Hide 87212F 28.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

a.
I112342C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 2 air duct.


Hide 87212 29.REMOVE REAR NO. 1 AIR DUCT (w/ Rear Air Duct)

a.
I112501

Disengage the claws to remove the rear No. 1 air duct.


Hide 55306A 30.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

w/ PTC Heater:

i.
E339409

Remove the bolt to disconnect the ground wire



b.
I112345

Remove the 2 nuts and separate the relay block assembly.


c.

for LHD:

i.
I113757

Disengage the clamps to disconnect the wire harness.


ii.
I113758

Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.



d.

for RHD:

i.
I113738

Disengage the clamps to disconnect the wire harness.


ii.
I113739

Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.



Hide 55307C 31.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

for LHD:

i.
I112542

Remove the bolt to disconnect the ground wire.


ii.

Disengage the clamps to disconnect the wire harness.


iii.

Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.



b.

for RHD:

i.
I113736

Remove the bolt to disconnect the ground wire.


ii.

Disengage the clamps to disconnect the wire harness.


iii.
I113737

Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.



Hide 55308B 32.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
I112348

Disengage the clamp and claws.


b.

Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.


Hide 82141 33.DISCONNECT INSTRUMENT PANEL WIRE

a.

for LHD:

i.

Disconnect each connector.

I113759C01
3.292,4.354 4.083,5.115 4.083,5.115 3.885,4.354 true 2.323,4.063 2.625,3.604 2.625,3.604 2.51,4.323 true 0.833,4.938 1.094,5.146 true 0.49,5.177 0.75,5.385 true 5.51,0.979 5.625,0.51 5.625,0.51 6.219,0.635 true 4.021,0.438 4.385,0.479 true 3.135,0.76 3.271,0.563 true 3.031,1.083 3.875,1.365 3.875,1.365 3.656,1.052 true 1.885,1.219 1.583,1.365 true 0.719,0.865 0.521,1.063 true 2.615,4.646 2.729,4.948 true 5.531,3.354 5.688,3.625 true 6.25,2.573 6.74,3.01 6.74,3.01 6.49,3.104 true 4.073,5.135 4.333,5.354 0.26,0.219 10 true *a 6.813,2.969 7.073,3.188 0.26,0.219 10 true *a 5.708,3.667 5.969,3.885 0.26,0.219 10 true *a 2.583,3.406 2.844,3.625 0.26,0.219 10 true *a 2.677,4.99 2.938,5.208 0.26,0.219 10 true *a 1.031,5.167 1.292,5.385 0.26,0.219 10 true *a 1.344,1.292 1.563,1.49 0.219,0.198 10 true *a 0.729,0.719 0.99,0.938 0.26,0.219 10 true *a 3.302,0.417 3.563,0.635 0.26,0.219 10 true *a 3.74,0.313 4,0.531 0.26,0.219 10 true *a 3.979,1.25 4.24,1.469 0.26,0.219 10 true *a 5.438,0.302 5.698,0.521 0.26,0.219 10 true *a 0.281,5.01 0.542,5.229 0.26,0.219 10 true *b
*a Clamp *b Hook



ii.

Remove the bolt and screw.


iii.

Remove the 4 bolts to disconnect the 4 ground wires.


iv.

Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.


v.

Disengage clamps and hook to disconnect the instrument panel wire.



b.

for RHD:

i.

Disconnect each connector.

I113760C01
3.417,5.25 2.677,4.583 true 3.281,4.406 3.979,4.865 3.979,4.865 3.917,4.406 true 6.542,5.031 6.729,4.646 6.729,4.646 6.573,4.375 true 2.896,5.313 3.417,5.25 3.417,5.25 2.542,3.99 true 6.302,5.49 5.906,5.375 true 1.01,4.802 0.781,4.906 true 0.917,5.552 0.719,5.469 true 1.521,0.438 1.271,0.5 true 1.073,1.229 0.813,1 true 3.396,1.052 3.917,1.25 3.917,1.25 4.198,0.979 true 2.708,1.135 2.938,1.313 true 6.396,0.906 6.625,1.083 true 0.552,2.719 1.052,3 1.052,3 0.979,2.406 true 6.781,4.552 6.99,4.76 0.208,0.208 10 true *a 5.708,5.281 5.917,5.49 0.208,0.208 10 true *a 3.479,5.208 3.688,5.417 0.208,0.208 10 true *a 3.917,4.906 4.125,5.115 0.208,0.208 10 true *a 1.021,4.688 1.229,4.896 0.208,0.208 10 true *a 1.021,1.188 1.229,1.396 0.208,0.208 10 true *a 1.063,0.427 1.271,0.635 0.208,0.208 10 true *a 2.938,1.26 3.146,1.469 0.208,0.208 10 true *a 3.823,1.26 4.031,1.469 0.208,0.208 10 true *a 6.219,0.75 6.427,0.958 0.208,0.208 10 true *a 0.938,5.51 1.146,5.719 0.208,0.208 10 true *b 1.01,3.031 1.219,3.24 0.208,0.208 10 true *a 5.708,4.094 5.896,4.292 0.188,0.198 10 true A 5.688,4.365 5.844,4.542 0.156,0.177 10 true A
*a Clamp *b Hook



ii.

Remove the bolt and screw.


iii.

Remove the 4 bolts to disconnect the 4 ground wires.


iv.

Remove the 2 nuts A.


v.

Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.


vi.

Disengage clamps and hook to disconnect the instrument panel wire.



Hide 88539J 34.DISCONNECT DRAIN COOLER HOSE

a.
I112352C01
1.656,3.083 1.24,2.896 true 1.688,3 1.948,3.208 0.26,0.208 10 true *1
*1 Cooler Unit Drain Hose Grommet


Disconnect the drain cooler hose.

NOTICE:

If the cooler unit drain hose grommet is disconnected from the vehicle body while disconnecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.



Hide 35.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.
I112482

Remove the 2 bolts.


b.

Remove the 5 bolts.

I113761


c.

Remove the nut.


d.
I112356

Disengage the clamps.


e.

Disconnect 2 connectors.


f.

Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I112546C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 36.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.

I112548


Hide 55990B 37.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY

a.
I112349

Disengage the 6 claws to remove the lower defroster nozzle assembly.