Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › from 2020.08
RM32K0E _51 Engine / Hybrid System _059913 2ZR-FXE ENGINE MECHANICAL _0293919 CYLINDER HEAD GASKET A

2ZR-FXE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link

*1: If the vehicle height has changed due to suspension or tire replacement

Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
Replacement of inverter with converter assembly Resolver learning
·

DTCs are stored

·

Slight vibration at a vehicle speed of 5 km/h (3 mph) or less

·

Shock or vibration during acceleration


(Click here)for Nickel Metal Hydride Battery
(Click here)for Lithium-ion Battery
Replacement of hybrid vehicle transaxle assembly
·

Resolver learning

·

Initialize resolver


Replacement of ECM Vehicle Identification Number (VIN) registration MIL comes on (Click here)
·

Replacement of throttle body assembly

·

Replacement of cylinder head sub-assembly

·

Replacement of camshaft (for intake or exhaust camshaft)

·

Replacement of camshaft timing gear assembly

·

Replacement of fuel injector assembly

·

Replacement of ignition coil assembly

·

Replacement of EGR valve assembly

·

Gas leak from exhaust system is repaired


Inspection After Repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)
Front wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Brake warning light / yellow (minor malfunction) illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


for Initialization:
(Click here)
for Calibration:
(Click here)
Suspension, tires, etc.*1
(The vehicle height changes because of suspension or tire replacement.)
·

Measure ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
·

Parking assist ECU initialization

·

Adjust steering angle


Panoramic view monitor system (Click here)
Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)

NOTICE:
·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Audio and Visual System (for HV Model))

·

After the power switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the power switch off, make sure to wait at least 85 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal. (for Navigation System (for HV Model))



HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1
Toyota parking assist-sensor system*1

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 16331 3.REMOVE WATER OUTLET (w/ Flow Shutting Valve (Water Valve))

Hide 16331 4.REMOVE WATER OUTLET (w/o Flow Shutting Valve (Water Valve))

Hide 25620 6.REMOVE EGR VALVE ASSEMBLY WITH EGR COOLER

Hide 7.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 9.REMOVE EXHAUST MANIFOLD (TWC: Front Catalyst)

Hide 15301 11.REMOVE ENGINE OIL LEVEL DIPSTICK

Hide 11452 12.REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 16289 13.REMOVE NO. 5 WATER BY-PASS PIPE

Hide 1628A 14.REMOVE NO. 6 WATER BY-PASS PIPE

Hide 17650G 15.REMOVE PURGE VALVE (PURGE VSV)

Hide 23818 16.REMOVE FUEL VAPOR FEED PIPE

Hide 23807 17.REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23807V 18.REMOVE NO. 1 DELIVERY PIPE SPACER

Hide 23250 19.REMOVE FUEL INJECTOR ASSEMBLY

Hide 11101E 21.REMOVE CAMSHAFT POSITION SENSOR

Hide 11201 22.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 11213 23.REMOVE CYLINDER HEAD COVER GASKET

Hide 11193 24.REMOVE SPARK PLUG TUBE GASKET

Hide 25.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

Hide 13540 27.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11302A 28.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 11302 29.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 13559 30.REMOVE CHAIN TENSIONER SLIPPER

Hide 13561 31.REMOVE NO. 1 CHAIN VIBRATION DAMPER

Hide 13562 32.REMOVE NO. 2 CHAIN VIBRATION DAMPER

Hide 13506 33.REMOVE CHAIN SUB-ASSEMBLY

a.
A374439C01
2.823,2.406 2.958,1.75 true 1.75,4.073 0.594,3.813 true 1.823,4.031 2.135,4.188 0.313,0.156 10 true *a 2.958,1.615 3.271,1.771 0.313,0.156 10 false *b
*a Loosen the Chain Sub-assembly
*b Place the chain sub-assembly on the non-toothed portion of camshaft timing gear assembly


Using a wrench to hold the hexagonal portion of the camshaft, turn the camshaft timing gear assembly counterclockwise to loosen the chain sub-assembly between the camshaft timing sprocket and camshaft timing gear assembly.


b.

With the chain sub-assembly loosened, separate the chain sub-assembly from the teeth of the camshaft timing gear assembly and place it on the non-toothed portion of camshaft timing gear assembly.


c.

Turn the camshaft clockwise to return it to its original position and remove the chain sub-assembly.


Hide 13050 34.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13050 35.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13523G 36.REMOVE CAMSHAFT TIMING SPROCKET

Hide 11103 40.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13801 41.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 42.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 44.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 45.REMOVE CYLINDER HEAD GASKET

a.
A374457

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 46.INSPECT CYLINDER HEAD SET BOLT