Home › Engine / Hybrid System › M20A-FXS (ENGINE MECHANICAL) › ENGINE UNIT › from 2020.08
RM32K0E _51 Engine / Hybrid System _083976 M20A-FXS ENGINE MECHANICAL _0404455 ENGINE UNIT A

M20A-FXS ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the removal of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 19100P 1.REMOVE SPARK PLUG

Hide 89615 2.REMOVE KNOCK CONTROL SENSOR

Hide 89448D 3.REMOVE OIL PRESSURE AND TEMPERATURE SENSOR

Hide 15250 4.REMOVE OIL PRESSURE CONTROL VALVE ASSEMBLY

Hide 11102A 5.REMOVE CAMSHAFT POSITION SENSOR (for Intake Side)

Hide 11102A 6.REMOVE CAMSHAFT POSITION SENSOR (for Exhaust Side)

Hide 15370 7.REMOVE CAM TIMING OIL CONTROL SOLENOID ASSEMBLY

Hide 13090D 8.REMOVE CAM TIMING CONTROL MOTOR WITH EDU ASSEMBLY

Hide 13090E 9.REMOVE CAM TIMING CONTROL MOTOR O-RING

Hide 15710 10.REMOVE OIL COOLER ASSEMBLY

Hide 11.REMOVE NO. 1 WATER BY-PASS HOSE

a.
A437850

Slide the clip and remove the No. 1 water by-pass hose from the cylinder block sub-assembly.


Hide 16264 12.REMOVE NO. 2 WATER BY-PASS HOSE

a.
A437851

Slide the clip and remove the No. 2 water by-pass hose from the water by-pass pipe sub-assembly.


Hide 12180E 13.REMOVE OIL FILLER CAP ASSEMBLY

a.
A424991

Remove the oil filler cap assembly from the cylinder head cover sub-assembly.


Hide 12108A 14.REMOVE OIL FILLER CAP GASKET

a.
A366042

Remove the oil filler cap gasket from the oil filler cap assembly.


Hide 11401G 15.REMOVE CRANKSHAFT POSITION SENSOR

Hide 12204C 16.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 13470 17.REMOVE CRANKSHAFT PULLEY ASSEMBLY

a.
A433566C01
1,1.083 0.583,1.083 0.583,1.083 0.854,0.646 false 0.031,0.323 0.344,0.521 0.313,0.198 10 false *a 2.406,1.865 2.719,2.063 0.313,0.198 10 false *b 0.25,1.01 0.708,1.208 0.458,0.198 10 false SST
*a Hold
*b Turn


Using SST, hold the crankshaft pulley assembly and loosen the crankshaft pulley bolt. Further loosen the crankshaft pulley bolt until 2 or 3 threads remain screwed into the crankshaft.

SST
09213-54015  
09330-00021  


b.
A433567C01
1.052,1.167 1.302,1.167 false 1.74,0.281 2.042,0.698 true 1.573,0.167 1.885,0.365 0.313,0.198 10 false *1 0.75,1.083 1.208,1.281 0.458,0.198 10 false SST 0.313,1.906 0.625,2.104 0.313,0.198 10 false *a 1.146,3 1.458,3.198 0.313,0.198 10 false *b
*1 Crankshaft Pulley Bolt
*a Hold
*b Turn


Using SST and the crankshaft pulley bolt, remove the crankshaft pulley assembly and crankshaft pulley bolt.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05070, 09957-04010)

HINT:

Apply lubricant to the threads and end of SST.



Hide 18.REMOVE INLET HEATER WATER HOSE

a.
A452242

Slide the clip and remove the inlet heater water hose from the outlet water by-pass sub-assembly.


Hide 19.REMOVE OUTLET HEATER WATER HOSE

a.
A452243

Slide the clip and remove the outlet heater water hose from the outlet water by-pass sub-assembly.


Hide 16304 20.REMOVE WATER OUTLET SUB-ASSEMBLY

a.
A433568

Remove the 2 bolts, water outlet sub-assembly and water outlet gasket from the cylinder head sub-assembly.


Hide 16351 21.REMOVE WATER BY-PASS OUTLET

a.
A437853

Using an 8 mm socket wrench, remove the 3 bolts, water by-pass outlet and water pipe outlet gasket from the cylinder head sub-assembly.


Hide 11201 22.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A424995

Using an 8 mm socket wrench, remove the 16 bolts and cylinder head cover sub-assembly from the camshaft housing sub-assembly.


b.
A424996

Remove the 7 cylinder head cover gaskets from the cylinder head cover sub-assembly.


c.
A424997

Remove the camshaft bearing cap oil hole gasket from the No. 1 camshaft bearing cap.


Hide 11193 23.REMOVE SPARK PLUG TUBE GASKET

a.
A427788C01
2.25,0.583 2.083,0.583 2.083,0.583 1.76,0.875 true 2.313,0.51 2.531,0.698 0.219,0.188 10 true *a
*a Protective Tape


Using a screwdriver, pry out the 4 spark plug tube gaskets from the cylinder head cover sub-assembly.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 12315A 24.REMOVE ENGINE MOUNTING BRACKET RH

a.
A424999

Remove the 3 bolts and engine mounting bracket RH from the No. 2 timing chain cover assembly.


Hide 25.REMOVE STRAIGHT SCREW PLUG

a.
A425000

Using a 10 mm hexagon wrench, remove the straight screw plug from the No. 2 timing chain cover assembly.


Hide 11320B 26.REMOVE NO. 2 TIMING CHAIN COVER ASSEMBLY

a.
A425001

Remove the 20 bolts.


b.

Remove the No. 2 timing chain cover assembly from the timing chain cover assembly by prying the No. 2 timing chain cover assembly with a screwdriver with its tip wrapped with protective tape.

A426575C01
2.073,2.854 1.469,3.573 1.469,3.573 1.979,4.167 true 5.115,1.438 5.427,1.875 5.427,1.875 5.073,2.229 true 1.25,3.469 1.469,3.646 0.219,0.177 10 true *a 5.458,1.802 5.677,1.979 0.219,0.177 10 true *a
*a Protective Tape - -


NOTICE:

Be careful not to damage the contact surfaces of the No. 2 timing chain cover assembly and timing chain cover assembly.



Hide 11301C 27.REMOVE TIMING CHAIN COVER OIL SEAL

a.
A400330C01
1.771,1.031 1.729,0.188 1.729,0.188 1.615,0.188 true 2.302,0.917 2.469,0.302 2.469,0.302 2.625,0.302 true 1.417,0.094 1.729,0.292 0.313,0.198 10 false *a 2.698,0.208 3.01,0.406 0.313,0.198 10 false *b
*a Protective Tape
*b Wooden Block


Using a screwdriver and wooden block, pry out the timing chain cover oil seal.

NOTICE:

Do not damage the surface of the timing chain cover oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.



Hide 28.SET NO. 1 CYLINDER TO TDC (COMPRESSION)

a.

Temporarily install the crankshaft pulley bolt.

A426576C01
1.25,2.5 0.719,3.031 0.719,3.031 1.146,2.875 true 6.313,2.396 6.042,2.5 6.042,2.5 6.302,2.604 true 3.396,5.75 2.063,5.75 true 1.875,5.635 2.188,5.792 0.313,0.156 10 false *1 1.115,0.25 1.427,0.406 0.313,0.156 10 false *a 6.135,0.281 6.448,0.438 0.313,0.156 10 false *b 3.917,5.167 4.229,5.323 0.313,0.156 10 false *c 5.813,2.406 6.031,2.604 0.219,0.198 10 true *d 0.49,2.938 0.708,3.135 0.219,0.198 10 true *d
*1 Crankshaft Timing Gear Key - -
*a Approximately 4.63° *b Approximately 33.07°
*c Approximately 2.73° *d Timing Mark



b.

Rotate the crankshaft clockwise and align the crankshaft timing gear key as shown in the illustration.


c.

Check that the timing marks on the camshaft timing exhaust gear assembly and camshaft timing gear assembly are as shown in the illustration.


d.

Remove the crankshaft pulley bolt.

HINT:

As the exhaust camshaft sub-assembly may rotate counterclockwise strongly when the crankshaft pulley bolt is removed, use a wrench to hold the hexagonal portion of the exhaust camshaft sub-assembly.



Hide 13507A 29.REMOVE OIL PUMP DRIVE CHAIN SUB-ASSEMBLY

a.

Temporarily install the crankshaft pulley assembly with the crankshaft pulley bolt.


b.
A433574C02
0.896,0.656 0.479,0.417 false 2.188,1.823 1.542,1.333 true 0.771,1.542 1.083,1.698 0.313,0.156 10 false *a 0.167,0.344 0.604,0.542 0.438,0.198 10 false SST 2.219,1.74 2.615,1.948 0.396,0.208 10 true SST
*a Bolt


While holding the crankshaft pulley assembly with SST, remove the bolt.

SST
09213-54015  
09330-00021  


c.

Remove SST, the crankshaft pulley bolt and crankshaft pulley assembly.


d.
A426792C01
0.552,1.604 0.302,1.531 false 1.792,1.167 1.563,0.99 true 0.135,1.448 0.448,1.604 0.313,0.156 10 false *1 1.823,1.094 2.021,1.281 0.198,0.188 10 true *2
*1 Chain Tensioner Plate
*2 Chain Damper Spring


Remove the chain tensioner plate and chain damper spring.


e.
A400739C01
0.719,0.792 0.896,0.792 0.896,0.792 1.333,1.271 false 0.74,1.729 0.656,1.156 0.656,1.156 0.521,1.156 false 0.594,2.865 0.552,2.521 0.552,2.521 0.396,2.521 false 0.552,0.719 0.865,0.917 0.313,0.198 10 false *1 0.333,1.073 0.646,1.271 0.313,0.198 10 false *2 0.229,2.406 0.542,2.604 0.313,0.198 10 false *3
*1 Oil Pump Drive Chain Sub-assembly
*2 Oil Pump Drive Sprocket
*3 Oil Pump Drive Shaft Sprocket


Remove the oil pump drive sprocket, oil pump drive shaft sprocket and oil pump drive chain sub-assembly.


Hide 13050 30.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A432202C01
1.667,1.219 1.958,0.875 1.958,0.875 2.115,0.875 true 2.125,0.792 2.438,0.99 0.313,0.198 10 true *a
*a Loosen
V113147

Turn


Hold the hexagonal portion of the exhaust camshaft sub-assembly with a wrench and turn the camshaft timing gear assembly clockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and camshaft timing gear assembly.


b.
A432203C01
1.885,0.219 2.198,0.417 0.313,0.198 10 false *a
*a Hold
V113147

Turn


Using a wrench, hold the hexagonal portion of the intake camshaft sub-assembly.

NOTICE:
·

Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube with the wrench.

·

Do not disassemble the camshaft timing gear assembly.




c.

Using a 10 mm bi-hexagonal wrench, remove the bolt and camshaft timing gear assembly from the intake camshaft sub-assembly.


Hide 13506 31.REMOVE CHAIN SUB-ASSEMBLY

a.
A400338

Remove the crankshaft timing sprocket and chain sub-assembly.


Hide 13540 32.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A432204

Using an 8 mm socket wrench, remove the bolt.


b.

Remove the nut and No. 1 chain tensioner assembly from the timing chain cover assembly.

NOTICE:

Make sure that the plunger, check ball assembly and spring do not come out.



c.
A430094C01
2.156,0.729 2.427,0.313 2.427,0.313 2.573,0.313 false 2.656,0.229 2.969,0.427 0.313,0.198 10 false *a
*a Tape


Use tape to hold the plunger inside the No. 1 chain tensioner assembly.

NOTICE:
·

Make sure that the plunger, check ball assembly and spring do not come out.

·

If the No. 1 chain tensioner assembly comes apart, reinstall the parts as shown in the illustration.

A430095C01
3.552,1.552 3.708,1.552 3.708,1.552 3.969,1.135 false 3.042,0.938 3.302,0.521 3.302,0.521 3.458,0.521 false 2.24,0.854 2.5,0.438 2.5,0.438 2.656,0.438 false 1.563,0.521 1.771,0.281 1.771,0.281 1.906,0.281 false 3.354,1.469 3.667,1.667 0.313,0.198 10 false *a 3.552,0.427 3.865,0.625 0.313,0.198 10 false *b 2.74,0.354 3.052,0.552 0.313,0.198 10 false *c 1.99,0.188 2.302,0.385 0.313,0.198 10 false *d
*a Plunger *b Check ball assembly
*c Spring *d No. 1 chain tensioner assembly body





Hide 13559 33.REMOVE CHAIN TENSIONER SLIPPER

a.
A432205

Remove the bolt and chain tensioner slipper from the timing chain cover assembly.


Hide 13561 34.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A426599

Remove the 2 bolts and No. 1 chain vibration damper from the timing chain cover assembly.


Hide 13070A 35.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A462670

Using a wrench, hold the hexagonal portion of the exhaust camshaft sub-assembly.

NOTICE:

Be careful not to damage the camshaft housing sub-assembly, cylinder head sub-assembly and spark plug tube with the wrench.



b.

Using a 5 mm hexagon socket wrench, remove the 3 bolts.


c.
A462671C07
0.802,0.708 0.948,0.708 0.948,0.708 1.156,1.177 false 0.427,1.313 0.542,1.313 0.542,1.313 0.542,1.771 false 0.604,0.615 0.917,0.813 0.313,0.198 10 false *1 0.25,1.208 0.563,1.406 0.313,0.198 10 false *2
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Timing Oil Control Valve Assembly (Exhaust Camshaft Timing Gear Bolt Assembly)


Remove the camshaft timing exhaust gear assembly and camshaft timing oil control valve assembly (exhaust camshaft timing gear bolt assembly) from the exhaust camshaft sub-assembly.


Hide 11310 36.REMOVE TIMING CHAIN COVER ASSEMBLY

a.
A434753

Remove the 20 bolts and timing chain cover assembly from the camshaft housing sub-assembly, cylinder head sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and oil pump assembly.


b.

Remove the timing chain cover assembly by prying between the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly and stiffening crankcase assembly with a screwdriver with its tip wrapped with protective tape.

A434754C01
2.063,2.385 1.583,2.25 1.583,2.25 1.938,1.958 true 1.51,4.167 1.906,3.875 true 6.01,1.167 6.219,0.969 true 6.104,2.729 6.313,2.531 true 1.375,2.156 1.573,2.344 0.198,0.188 10 true *a 1.313,4.073 1.625,4.271 0.313,0.198 10 false *a 6.25,0.854 6.458,1.052 0.208,0.198 10 true *a 6.313,2.417 6.521,2.615 0.208,0.198 10 true *a
*a Protective Tape - -


NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly, camshaft housing sub-assembly, cylinder block sub-assembly, stiffening crankcase assembly and timing chain cover assembly.



Hide 15703A 37.REMOVE OIL NOZZLE VALVE SUB-ASSEMBLY

a.
A444976

Remove the oil nozzle valve sub-assembly from the cylinder block sub-assembly.


Hide 13471A 38.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A401230C01
0.917,1.219 0.542,0.781 0.542,0.781 0.385,0.781 true 0.125,0.656 0.344,0.854 0.219,0.198 10 true *a
*a Protective Tape


Using a screwdriver, remove the 2 crankshaft timing gear keys from the crankshaft.

HINT:

Tape the screwdriver tip before use.



Hide 23477 39.REMOVE FUEL PUMP LIFTER GUIDE

a.
A426594

Using an 8 mm socket wrench, remove the 2 bolts and fuel pump lifter guide from the No. 4 camshaft bearing cap.


Hide 11103 40.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

a.
A426573N01
3.25,1.24 3.406,1.438 0.156,0.198 10 true 2 3.271,0.188 3.427,0.385 0.156,0.198 10 true 1 2.844,0.021 3,0.219 0.156,0.198 10 true 3 3.135,1.875 3.292,2.073 0.156,0.198 10 true 4 2.385,0.635 2.542,0.833 0.156,0.198 10 true 5 0.042,0.063 0.167,0.229 0.125,0.167 10 true 6 0.042,1.781 0.167,1.948 0.125,0.167 10 true 7 0.073,1.26 0.198,1.427 0.125,0.167 10 true 8 2.375,0.083 2.5,0.25 0.125,0.167 10 true 9 2.385,1.917 2.604,2.083 0.219,0.167 10 true 10 1.875,0.542 2.094,0.708 0.219,0.167 10 true 11 0.76,0.052 0.979,0.219 0.219,0.167 10 true 12 0.781,1.969 1,2.135 0.219,0.167 10 true 13 0.563,0.604 0.781,0.771 0.219,0.167 10 true 14 1.719,0.042 1.938,0.208 0.219,0.167 10 true 15 1.594,1.948 1.813,2.115 0.219,0.167 10 true 16 1.25,0.583 1.469,0.75 0.219,0.167 10 true 17

Uniformly loosen and remove the 17 bolts in the order shown in the illustration.


b.
A400342

Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 41.REMOVE CAMSHAFT BEARING CAP

a.
A426591C01
0.594,1.635 0.365,1.854 true 1.104,1.604 1.104,1.813 true 1.625,1.615 1.625,1.823 true 2.135,1.615 2.01,1.844 true 2.698,0.573 2.406,0.177 true 0.177,1.781 0.427,1.969 0.25,0.188 10 false *1 1.042,1.854 1.354,2.01 0.313,0.156 10 false *2 1.563,1.854 1.875,2.01 0.313,0.156 10 false *3 2.229,0.083 2.542,0.24 0.313,0.156 10 false *4 1.927,1.875 2.24,2.031 0.313,0.156 10 false *3 0.073,1.073 0.24,1.26 0.167,0.188 10 false 1 2.177,1.792 2.344,1.979 0.167,0.188 10 true 2 3.021,1.396 3.188,1.583 0.167,0.188 10 true 3 1.406,0.594 1.573,0.781 0.167,0.188 10 true 4 0.604,1.323 0.771,1.51 0.167,0.188 10 true 5 2.521,0.625 2.688,0.813 0.167,0.188 10 true 6 1.719,1.448 1.885,1.635 0.167,0.188 10 true 7 1.99,0.531 2.156,0.719 0.167,0.188 10 true 8 1.271,1.469 1.438,1.656 0.167,0.188 10 true 9
*1 No. 1 Camshaft Bearing Cap
*2 No. 2 Camshaft Bearing Cap
*3 No. 3 Camshaft Bearing Cap
*4 No. 4 Camshaft Bearing Cap


Remove the 9 bolts in the order shown in the illustration.


b.

Remove the No. 1 camshaft bearing cap, No. 2 camshaft bearing cap, 2 No. 3 camshaft bearing caps and No. 4 camshaft bearing cap from the camshaft housing sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13501A 42.REMOVE INTAKE CAMSHAFT SUB-ASSEMBLY

a.
A426097

Remove the intake camshaft sub-assembly from the camshaft housing sub-assembly.


Hide 13502B 43.REMOVE EXHAUST CAMSHAFT SUB-ASSEMBLY

a.
A426098

Remove the exhaust camshaft sub-assembly from the camshaft housing sub-assembly.


Hide 13801 44.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A404210

Remove the 16 No. 1 valve rocker arm sub-assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13750 45.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A404211

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 13716 46.REMOVE VALVE STEM CAP

a.
A404212

Remove the 16 valve stem caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



Hide 16268 47.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A425186

Using an 8 mm socket wrench, remove the 2 bolts, No. 1 water by-pass pipe and water by-pass pipe gasket from the cylinder head sub-assembly.


Hide 11101 48.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A400296C03
0.49,1.948 0.646,2.146 0.156,0.198 10 true 1 2.927,0.24 3.083,0.438 0.156,0.198 10 true 2 0.5,0.24 0.656,0.438 0.156,0.198 10 true 3 2.875,1.958 3.031,2.156 0.156,0.198 10 true 4 1.104,1.948 1.26,2.146 0.156,0.198 10 true 5 2.281,0.323 2.438,0.521 0.156,0.198 10 true 6 1.083,0.281 1.24,0.479 0.156,0.198 10 true 7 2.281,1.927 2.438,2.125 0.156,0.198 10 true 8 1.667,0.302 1.823,0.5 0.156,0.198 10 true 9 1.698,1.938 1.906,2.125 0.208,0.188 10 true 10
V100136

Front of Engine


Using a 12 mm socket wrench, uniformly loosen the 10 cylinder head set bolts in the order shown in the illustration. Remove the 10 cylinder head set bolts and 10 plate washers.

NOTICE:
·

Be careful not to drop the plate washers into the cylinder head sub-assembly.

·

Warpage or cracking of the cylinder head sub-assembly may result from removing the cylinder head set bolts in the incorrect order.



HINT:

Arrange the removed parts in such a way that they can be reinstalled to their original locations.



b.

Remove the cylinder head sub-assembly from the cylinder block sub-assembly.


Hide 11445 50.REMOVE CYLINDER BLOCK WATER JACKET SPACER

a.
A425185

Remove the cylinder block water jacket spacer from the cylinder block sub-assembly.

NOTICE:

Be sure to remove the cylinder block water jacket spacer. If it is not removed, it may fall and become damaged when the cylinder block sub-assembly is inverted.



Hide 15601 51.REMOVE OIL FILTER SUB-ASSEMBLY

Hide 15600A 52.REMOVE OIL FILTER UNION

A433576

a.

Using a 12 mm hexagon socket wrench, remove the oil filter union from the stiffening crankcase assembly.


Hide 12101A 53.REMOVE OIL PAN DRAIN PLUG

a.

Remove the oil pan drain plug and gasket from the oil pan sub-assembly.


Hide 12101 54.REMOVE OIL PAN SUB-ASSEMBLY

a.
A433577C01
2.719,1.469 2.948,1.667 0.229,0.198 10 true *a 1.292,2 1.458,2.177 0.167,0.177 10 false *a
*a Nut


Remove the 12 bolts and 2 nuts.


b.
A118769

Insert the blade of an oil pan seal cutter between the oil pan sub-assembly and stiffening crankcase assembly, cut through the applied sealer and remove the oil pan sub-assembly.

NOTICE:
·

Be careful not to damage the contact surfaces of the stiffening crankcase assembly and oil pan sub-assembly.

·

Be careful not to damage the oil pan sub-assembly flange.




Hide 15104 55.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A433578

Using an 8 mm socket wrench, remove the bolt, oil strainer sub-assembly and oil strainer gasket from the stiffening crankcase assembly.


Hide 89491 56.REMOVE ENGINE OIL LEVEL SENSOR

Hide 13620B 57.REMOVE ENGINE BALANCER ASSEMBLY

a.
A433579

Remove the 6 bolts and engine balancer assembly from the stiffening crankcase assembly.

NOTICE:

Do not disassemble the engine balancer assembly.



Hide 15100 58.REMOVE OIL PUMP ASSEMBLY

Hide 11420 59.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A433591

Remove the 7 bolts.


b.
A433580

Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly at the places shown in the illustration.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly and stiffening crankcase assembly.


HINT:

Tape the screwdriver tip before use.



Hide 60.REMOVE STRAIGHT SCREW PLUG

a.
A433581

Using a 10 mm hexagon socket wrench, remove the straight screw plug and gasket from the stiffening crankcase assembly.


Hide 61.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 62.REMOVE RING PIN

NOTICE:

It is not necessary to remove the ring pins unless they are being replaced.


Hide 63.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pins unless they are being replaced.


Hide 11401L 64.REMOVE REAR ENGINE OIL SEAL

a.
A425011

Remove the rear engine oil seal from the cylinder block sub-assembly.