Home › Engine / Hybrid System › M20A-FXS (HYBRID / BATTERY CONTROL) › HV BATTERY › from 2020.08
RM32K0E _51 Engine / Hybrid System _083959 M20A-FXS HYBRID / BATTERY CONTROL _0404417 HV BATTERY A

M20A-FXS HYBRID / BATTERY CONTROL  HV BATTERY  INSTALLATION  


PROCEDURE

Hide G920Q 2.INSTALL NO. 1 HYBRID BATTERY SHIELD SUB-ASSEMBLY

Hide G92J5 4.INSTALL NO. 1 HYBRID BATTERY PACKING

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.
A443799C02
1.385,0.469 1.448,0.177 1.448,0.177 1.635,0.177 false 1.896,0.49 1.958,0.177 1.958,0.177 2.146,0.177 false 2.167,0.083 2.479,0.281 0.313,0.198 10 false *1 1.656,0.073 1.969,0.271 0.313,0.198 10 false *a
*1 No. 1 Hybrid Battery Packing
*a Tape


Engage the 2 claws to install the No. 1 hybrid battery packing to the HV battery.

NOTICE:

Align each tape on the hybrid battery thermistor with the edge of the No. 1 hybrid battery packing as shown in the illustration and then engage the 2 claws to install the No. 1 hybrid battery packing to the HV battery.



Hide G92Z2 5.INSTALL HYBRID BATTERY TERMINAL BLOCK

Hide G920L 8.INSTALL UPPER NO. 1 HYBRID BATTERY COVER SUB-ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.


a.

Install the upper No. 1 hybrid battery cover sub-assembly to the HV battery with the 7 bolts and 6 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 9.INSTALL HV BATTERY

CAUTION:

Be sure to wear insulated gloves.


a.
A443780C02
2.958,0.594 3.156,0.781 0.198,0.188 10 true *a 2.167,0.333 2.375,0.531 0.208,0.198 10 true *a 1.51,0.26 1.729,0.458 0.219,0.198 10 true *b 2.969,1.917 3.146,2.115 0.177,0.198 10 true *a 0.094,0.677 0.292,0.875 0.198,0.198 10 true *a
*a Bolt (A)
(Bolt Length: 25 mm (0.984 in.))
*b Bolt (B)
(Bolt Length: 24 mm (0.945 in.))


Install the HV battery to the vehicle with the 4 bolts (A) and bolt (B).

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not allow foreign matter, such as grease or oil, to adhere to the bolts of the HV battery.

·

To prevent the wire harness from being caught, make sure to bundle the wire harness using insulating tape or equivalent.

·

Use cardboard or another similar material to protect the HV battery and vehicle body from damage.

·

Since the HV battery is very heavy, 2 people are needed to install it. When installing the HV battery, be careful not to damage the parts around it.

·

When removing/installing/moving the HV battery, make sure not to tilt it more than 80°.

·

While lowering the HV battery into the vehicle, do not allow it to contact the vehicle.

·

As bolts with 2 different lengths are used, make sure to install each bolt to the correct position.

·

If the HV battery has been struck or dropped, replace it.




Hide 82161 10.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the battery voltage sensor connector.


b.

Engage the clamp.


Hide G92PC 11.INSTALL NO. 1 HV BATTERY PROTECTOR

CAUTION:

Be sure to wear insulated gloves.


a.

Engage the claw to install the No. 1 HV battery protector to the HV battery.


b.

Install the clip.


Hide 82161 12.CONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the HV battery junction block assembly connector.


b.

Connect the electric vehicle battery plug assembly connector.


c.

Engage the clamp.


Hide 821H1 13.CONNECT FLOOR UNDER WIRE

CAUTION:

Be sure to wear insulated gloves.


a.

Connect the shield ground to the HV battery.


b.

Connect the 2 HV battery junction block assembly connectors.

NOTICE:

Make sure that the connectors are connected securely.



Hide G92N4A 14.INSTALL NO. 1 HV BATTERY COVER PANEL RH

CAUTION:

Be sure to wear insulated gloves.


a.
A444076C01
1.229,1.135 1.469,1.135 false 1.031,0.948 1.167,0.677 1.167,0.677 1.333,0.677 true 1.344,0.583 1.573,0.771 0.229,0.188 10 false *a 1.104,0.396 1.333,0.583 0.229,0.188 10 false *b 1.49,1.021 1.719,1.208 0.229,0.188 10 false *1
*1 Battery Cover Lock Striker
*a Button
*b Push


Install the No. 1 HV battery cover panel RH to the HV battery with the 3 bolts and 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Install the battery cover lock striker, then push the button to lock it.


Hide G9230 15.INSTALL BATTERY COOLING BLOWER ASSEMBLY

Hide 71033 16.INSTALL REAR SEAT CUSHION LEG SUB-ASSEMBLY

a.
A443791N01
1.76,1.938 1.917,2.135 0.156,0.198 10 true 1 2.74,1.917 2.896,2.115 0.156,0.198 10 true 2 3.167,1.094 3.323,1.292 0.156,0.198 10 true 3 0.74,1.49 0.875,1.688 0.135,0.198 10 true 4 0.219,1.24 0.375,1.438 0.156,0.198 10 true 5 0.76,0.26 0.917,0.458 0.156,0.198 10 true 6

Temporarily install the rear seat cushion leg sub-assembly with the 6 bolts.


b.

Fully tighten the 6 bolts in the order shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


Hide 76971G 17.INSTALL REAR UNDER COVER

a.

Engage the 2 guides to install the rear under cover to the rear seat cushion leg sub-assembly.


b.

Engage the 2 clips.


Hide 76974F 18.INSTALL REAR UNDER SIDE COVER LH

Hide 67918A 19.INSTALL REAR DOOR SCUFF PLATE LH

Hide 76973F 20.INSTALL REAR UNDER SIDE COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 67917A 21.INSTALL REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.


Hide 72693 22.INSTALL REAR SEAT CUSHION LOCK HOOK

Hide 23.INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Hide 73350C 24.CONNECT REAR CENTER SEAT OUTER BELT ASSEMBLY